145 Commits
Author SHA1 Message Date
af006cf1c3 feat(motor_failure_detector): add current-residual detection (#27711)
* feat(motor_failure_detector): add current-residual detection library

Per-motor model-based motor-failure detector for multirotors. Predicts the
expected ESC current from the commanded actuator signal
(I_exp = current_slope_a*u + current_idle_a) and trips on a low-pass-filtered
residual held past a trip band for a persistence time. The command (not measured
rpm) is the fault-independent reference: a dead motor that draws no current while
still commanded produces a large residual, whereas a current-vs-rpm model would
mask a clean stop.

Band and persistence are configurable per residual direction. Undercurrent is the
fault-consistent side -- an open circuit, a shed propeller or a desync makes a
motor draw less than commanded -- while overcurrent covers a winding short,
mechanical jam or demagnetization. They are separate because the benign residual
is far from symmetric: a fast throttle increase draws acceleration current the
static model cannot predict, so overcurrent excursions are large and unbounded,
whereas an undercurrent residual is floored at -I_exp. A single band sized to
reject the overcurrent transients can therefore end up wider than the largest
undercurrent fault a motor can physically produce, which makes a full current
collapse undetectable rather than merely slow. Set undercurrent_threshold_a <= 0
to keep one symmetric band on the residual magnitude.

Built on PX4 primitives rather than hand-rolled equivalents: update() takes a
timestamp (esc_status.timestamp in flight, the log timestamp in replay) and
derives dt internally; the residual filter is a mathlib AlphaFilter; the
persistence debounce is a systemlib::Hysteresis per direction (with a sticky latch
on top, and reset across data gaps so a dropout can't complete a pending trip).

The data-gap threshold (kMaxGap = 0.3 s) is sized above the ~10 Hz arming-check
feed interval and below the 400 ms ESC-offline timeout: a live feed is never
mistaken for a gap (a smaller value equal to the feed interval reset the filter
and debounce on the majority of jittered ticks, so a sustained fault never
survived the persistence window -- offline replay: 0/100 sampling phases latched
vs 100/100 gap-free), while a genuine outage still resets and is handled by the
separate ESC liveness guard.

Includes an 18-case gtest spanning the failure-mode spectrum and edge cases:
healthy-never-trips (incl. high throttle), open-circuit and overcurrent trips,
severe prop-loss undercurrent, the missed ~50% partial loss (documents the
detection floor), the per-direction bands (a tighter undercurrent band catching a
collapse one symmetric band misses, band independence, per-side persistence),
persistence (short spike crosses-threshold-but-recovers), gap reset, the 10 Hz
feed vs. real-gap boundary, dropout-holds, multi-motor, the exclusion gate,
monitor-only, and reset/latch.

* refactor(motor_failure_detector): resolve the undercurrent band at configure time

An unset undercurrent threshold now mirrors the overcurrent band in
configure(), so update() runs the same two bands in every configuration and
no longer carries a second threshold test that reads like a repeat of the
disable gate. A symmetric band is the two-band case with equal bands.

Also name esc_status CONNECTED_ESC_MAX at kMaxMotors so the constant is
findable, use the PX4 time literals for the persistence conversions, and
drop the excluded temporary.

* feat(commander): use current-residual detector for the ESC motor-failure check

Replace the flat, instantaneous current check in EscChecks::checkMotorStatus with
the MotorFailureDetector library (added in the parent PR). Per motor it predicts
the expected ESC current from the commanded thrust
(I_exp = MOTFAIL_C2T*u + MOTFAIL_IDLE) and trips on the low-pass-filtered
residual, with an independent band and hold time per direction: MOTFAIL_UNDER held
for MOTFAIL_UND_TIME below the expectation, MOTFAIL_OVER held for MOTFAIL_OVR_TIME
above it.

Because the two directions need separate bands, the single band and hold time are
renamed to name the direction they act on: MOTFAIL_OFF -> MOTFAIL_OVER and
MOTFAIL_TIME -> MOTFAIL_OVR_TIME, migrated in param_translation.cpp. The old band
applied to both directions, so it carries over to the overcurrent side, and
MOTFAIL_UNDER defaults to 0, which keeps a single symmetric band -- an existing
vehicle behaves as before. MOTFAIL_IDLE also defaults to 0, and the whole check
stays gated by FD_ACT_EN (off by default).

The detector is driven off esc_status.timestamp, so a telemetry stall freezes the
filter instead of integrating stale current; the separate 400 ms ESC telemetry
timeout stays in checkEscOnline(). It is reconfigured from parameters while
disarmed, so a parameter change never resets a latched failure mid-flight. The
motor_failure_mask still feeds failure_detector_status via
FailureDetector::publishStatus, leaving the ControlAllocator reaction path
untouched.

The mask reports the detector's sticky latch alone, not whether the motor is
currently evaluable. That preserves the invariant the previous check spelled out
-- "Only set, never clear mid-air: stopping the motor in response could make it
appear healthy again" -- because handling a failure makes exactly that motor
unevaluable: the control allocator drops it, which publishes a NAN command,
which excludes it from the detector. Re-deriving the mask from the exclusion
state clears it, the allocator restores all motors, and the next check re-trips.
Measured in SIH on a hexarotor with a missing propeller: 83 mask transitions in
nine seconds, with a reversed recovery motor swinging between idle and near-full
reverse at the 10 Hz check rate. An ESC going offline after a real failure
retracts the report the same way. The latch is only ever set on a tick where the
motor was evaluable, so reporting it alone cannot report a motor that was never
judged.

* feat(motor_failure_detector): add offline ulog replay tool

Add a host tool that replays a recorded .ulg through the real MotorFailureDetector
and prints the per-motor trip verdict, for validating and tuning the detector
offline (EKF2-replay style: the real library drives recorded data, not a
re-implementation).

Built on ulog_cpp (PX4's C++ ULog library, added as a git submodule and built for
the posix host target only), so it reads ESC current, motor command and arming
state by field name from the log's own format -- one binary replays logs of any
PX4 message version with no rebuild. The feed mirrors the runtime in escCheck:
evaluated only while armed, at the runtime's 10 Hz cadence, with the per-ESC
current-report startup latch and reset-on-disarm. Config comes from the log's
MOTFAIL_* parameters with a built-in calibration fallback, and --set
MOTFAIL_NAME=value overrides any knob for what-if retuning. Because the runtime's
exact 10 Hz sample phase cannot be reconstructed offline, a single pass over the log
drives several detector instances on staggered grid offsets and reports a per-motor
peak band and trip fraction rather than a single phase's verdict, flagging when the
result is phase-dependent.

batch_replay.sh runs the tool over a folder of logs and summarizes each verdict
(OK / FAIL / SKIP) from its exit code.

Off by default so it never enters the firmware build or CI: it is a posix-only,
EXCLUDE_FROM_ALL host executable gated behind the MFD_REPLAY_TOOL cache option.
Build it with:

    cmake -DMFD_REPLAY_TOOL=ON build/px4_sitl_default
    ninja -C build/px4_sitl_default mfd_replay

* docs(motor_failure_detector): document the current-residual motor-failure check

Add a configuration page for motor failure detection, next to the other
actuator topics, and a developer page for the offline replay tool:

- what the check compares and why the under/overcurrent bands are separate
- the new MOTFAIL_* parameters, including the rename migration
- how to fit the current model and pick the bands from the vehicle's own
  logs with mfd_replay / batch_replay.sh

The "Motor Failure Trigger" section in the failsafe page described the
pre-rename parameters, the unfiltered symmetric comparison and claimed the
failure was non-latching, so it is reduced to a summary of the trigger and
its action, pointing at the new page for the thresholds.

* docs(docs): Subedit for simpler introductions and terminology

* docs(docs): Improve upgrading from v1.18 section

* feat(motor_failure_detector): add current-model fitting tool

mfd_fit derives MOTFAIL_C2T and MOTFAIL_IDLE from recorded logs, so the model
and the thresholds are taken from the same data.

Like mfd_replay it reads ESC current, motor command and arming state through
ulog_cpp by field name, so one binary handles any log version. Each log is a
single streaming pass that accumulates only the sums a least-squares line needs,
so memory does not grow with the log or with the number of logs, and a whole
corpus can be fitted in one invocation.

Alongside the parameters it reports the residual spread the trip bands have to
clear, and each motor's bias against the shared model.

* docs(docs): document motor failure detection tuning and the fitting tool

Follow-up to review of the detection and replay pages:

- fix the link left behind by the Failure Response -> Failure Action rename
- drop the Multicopter badge: the check has no vehicle-type gate, so a VTOL's
  multirotor motors and its forward-flight motor are both checked
- describe the model-fitting step without the statistics jargon
- state that only healthy logs may be used, for the fit and the thresholds
- document mfd_fit, and reduce the release note to a pointer

* feat(motor_failure_detector): report residual extremes and add a band sweep

The replay tool printed the largest residual magnitude, which hid whether an
excursion was above or below the model. Since the two trip bands are chosen per
direction, that left the reader running one band at a time to find out. It now
prints the signed minimum and maximum instead, so each band's headroom is
readable straight from the table.

Add sweep_matrix.sh alongside batch_replay.sh: it sweeps one band against its
hold time over a set of logs and prints how many logs false-trip at each pair,
so the lowest usable band per hold time is the first zero in a row.

Both tools now number motors from 1, matching the "Motor N ..." the vehicle
reports, rather than from 0.

* docs(docs): rework the motor failure calibration walkthrough

Follow a real calibration through both pages and fix what it ran into:

- the replay page's worked example is one vehicle end to end, with every
  number and pasted output taken from that corpus
- the fitting tool, the single-log run and the band sweeps are ordered the way
  the work is actually done, with replaying a whole fleet last
- the sweeps are shown as a matrix of false trips per (hold time, band), and
  the grids are derived from the residual extremes rather than guessed
- commands match the output they produce, and say what they need: mfd_replay
  without --set uses a fallback calibration that belongs to another vehicle
- vehicle_status is optional, not required, for the replay
- drop the repetition: batch_replay.sh, the hover-current ceiling and the
  phase-sensitivity note were each explained two or three times

* fix(motor_failure_detector): separate configure and reset with the appropriate triggers

* refactor(motor_failure_detector): clarify leading edge hysteresis as trigger time compared to "persistence"

* fix(escCheck): encapsulate _motor_failure_direction handling into MotorFailureDetector

* fix(astyle): exclude ulog_cpp submodule form check

* fix(motor_failure_detector_tools): fail log replay when no log is present

* refactor(motor_failure_detector): Improve documentation

* fix(escCheck): check load per ESC not per motor function

This was already done in my original implementation. It supports checking multiple ESCs mapped to the same motor function individually. It's also consistent with other ESC checks that run for every ESC that reports telemetry.

* fix(motor_failure_detector): run update() per motor and consider individual telemetry timestamps

* fix(motor_failure_detector): simplify output interface to getters of actually used results

* fix(motor_failure_detector): inline what doesn't need to be separate

* fix(motor_failure_detector): make the bands independent and drop special cases

- Each trip band is now independent: a threshold <= 0 disables only that band. The undercurrent band no longer copies the overcurrent one.
- Drop the MOTFAIL_OFF/MOTFAIL_TIME parameter migration. The new parameters start at their defaults.
- Treat a non-finite current like a non-finite command (not evaluated, filter and debounce reset). No driver reports NaN current, so the path only existed for its test.
- Compute the residual as max(current, 0) - I_expected. Same as before, but written such that it's obvious: regeneration counts as 0A.
- Drop unnecessary trigger time parameter clamp to >= 0 before converting to unsigned microseconds, metadate already decalres that as out of range.
- Count each ESC sample once by its own timestamp in mfd_fit, like the motor_failure_detector.

* fix(motor_failure_detector): check all still considered online ESC telemetry

* fix(motor_failure_detector): declare all link dependencies

* fix(motor_failure_detector_tools): reuse log reading logic to reduce duplication

* fix(motor_failure_detector): replace reversible flag getting passed into the detector for separate handling

Having a NAN command already handles that.

* test(escChecks): add unit tests for load based failure detection

---------

Co-authored-by: Hamish Willee <hamishwillee@gmail.com>
Co-authored-by: Matthias Grob <maetugr@gmail.com>
Co-authored-by: Andrea Bernasconi <andrea.bernasconi@auterion.com>
2026-10-26 16:45:00 +01:00
Ramon Roche a23449cbe5 feat(simulation)!: remove jMAVSim
PX4 SIH with the Hawkeye visualizer replaces jMAVSim, in SITL and as the
display-only viewer for SIH running on hardware. Drop the jMAVSim
submodule, its make targets, px4-rc.jmavsim, the 10017_jmavsim_iris
airframe and the VS Code debug helpers, stop installing Java and ant in
the macOS and Arch setup scripts, and point the remaining mentions at SIH
and Hawkeye.

BREAKING CHANGE: make px4_sitl jmavsim and SYS_AUTOSTART 10017 no longer
exist. Use make px4_sitl_sih sihsim_quadx with Hawkeye instead.

Assisted-by: Claude:claude-opus-5-5
Signed-off-by: Ramon Roche <mrpollo@gmail.com>
2026-09-26 14:28:26 -07:00
Peter van der Perk bbcd20abe3 feat(git): upgrade NuttX to 12.12.0
Update git sha's for NuttX
2026-09-03 12:31:07 -07:00
Beniamino Pozzan 61106dc329 feat(uxrce_dds_client): allow building Micro-XRCE-DDS_Client v3 (#27597)
Adds new nuttx config entry: UXRCE_DDS_CLIENT_USE_DDS_V3

Signed-off-by: Beniamino Pozzan <beniamino.pozzan@gmail.com>
2026-06-07 18:58:23 +01:00
Ramon Roche b911d4414e build(sim): convert PX4-OpticalFlow to git submodule (#27184)
Replace the ExternalProject_Add-based fetch of PX4/PX4-OpticalFlow with a
proper git submodule at src/modules/simulation/gz_plugins/optical_flow/PX4-OpticalFlow,
matching how every other external C++ dependency is integrated in PX4 (mavlink,
gps/devices, Micro-XRCE-DDS-Client, libevents, heatshrink, etc.).

The previous approach cloned the repo over the network on every clean build,
pinned to GIT_TAG master (unreproducible), and had generated a string of
follow-up PRs over the last year chasing ExternalProject quirks (install
paths, macOS .dylib vs .so, permissions).

The plugin now consumes the upstream OpticalFlow target directly via
add_subdirectory and px4_add_git_submodule. The upstream repo predates PX4's
strict warning policy, so the OpticalFlow and klt_feature_tracker targets get
-Wno-error plus a few specific -Wno-* flags and -fvisibility=default to build
cleanly inside the PX4 tree.

Signed-off-by: Ramon Roche <mrpollo@gmail.com>
2026-04-23 11:57:02 -08:00
Eric Katzfey bd76832f34 voxl2: Added components to the board build that are in the ModalAI fork but missing in mainline 2026-02-24 09:48:33 -07:00
Jonas EschmannandHamish Willee db2c6b2abe feature: Integrating the RAPTOR foundation policy (#26082)
* moving raptor

bump

compiles and raptor mode appears

hovering with RAPTOR seems to work

Using Raptor to execute offboard commands works (using multirobot f03825a5795a77c5a095f799eeb8e0b646fe7176 to feed the trajectory_setpoint). Requires more testing

simplified rotmat

runtime inference frequency multiple

arming request response reflects actual readiness

adjusting to fit IMU gyro ratemax

relaxing control timing warning thresholds for SITL

Using mode registration to signal if offboard commands should be forwarded to trajectory_setpoint instead of just hardcoding vehicle_status.nav_state == vehicle_status_s::NAVIGATION_STATE_OFFBOARD

adopting new "request_offboard_setpoint" in raptor module

replace offboard seems good

mc_raptor: overwrite offboard parameter

separate raptor config

addendum

Raptor off by default

RAPTOR readme

Loading raptor checkpoint from tar works.

check if load was successful

refactoring: cutting out the pure C interface to allow direct testing of the policy input/output behavior from the file, without fully loading it into memory first

adapter not needed anymore

ripping out test observation mode (not used in a long time)

fixing warnings

bump RLtools to fix the remaining warnings

Loading RAPTOR checkpoint from sdcard seems to work on FMU-6C

embedding Raptor policy into flash works again

also printing checkpoint name when using the embedded policy

cleaner handling of the checkpoint name

back to reading from file

ripping out visual odometry checks

cleaner

more debug but no success

bump rlt

bump

pre next rebase

we can publish the no angvel update because we latch onto it with the scheduled work item anyways

this kind of runs on the 6c

still bad

SIH almost flying

saving stale traj setpoint yaw

new error. timestamp not the problem anymore

bump rlt; SIH works with executor

shaping up

bumping blob (include tar checkpoint)

cleaning up

fixing formatting

update readme

* moving raptor

bump

compiles and raptor mode appears

hovering with RAPTOR seems to work

Using Raptor to execute offboard commands works (using multirobot f03825a5795a77c5a095f799eeb8e0b646fe7176 to feed the trajectory_setpoint). Requires more testing

simplified rotmat

runtime inference frequency multiple

arming request response reflects actual readiness

adjusting to fit IMU gyro ratemax

relaxing control timing warning thresholds for SITL

Using mode registration to signal if offboard commands should be forwarded to trajectory_setpoint instead of just hardcoding vehicle_status.nav_state == vehicle_status_s::NAVIGATION_STATE_OFFBOARD

adopting new "request_offboard_setpoint" in raptor module

replace offboard seems good

mc_raptor: overwrite offboard parameter

separate raptor config

addendum

Raptor off by default

RAPTOR readme

Loading raptor checkpoint from tar works.

check if load was successful

refactoring: cutting out the pure C interface to allow direct testing of the policy input/output behavior from the file, without fully loading it into memory first

adapter not needed anymore

ripping out test observation mode (not used in a long time)

fixing warnings

bump RLtools to fix the remaining warnings

Loading RAPTOR checkpoint from sdcard seems to work on FMU-6C

embedding Raptor policy into flash works again

also printing checkpoint name when using the embedded policy

cleaner handling of the checkpoint name

back to reading from file

ripping out visual odometry checks

cleaner

more debug but no success

bump rlt

bump

pre next rebase

we can publish the no angvel update because we latch onto it with the scheduled work item anyways

this kind of runs on the 6c

still bad

SIH almost flying

saving stale traj setpoint yaw

new error. timestamp not the problem anymore

bump rlt; SIH works with executor

shaping up

bumping blob (include tar checkpoint)

cleaning up

fixing formatting

update readme

updating gitignore

* fixing format and declaring submodules as cmake dependencies

* adding uORB message documentation

* fixing comment alignment

* Adding option to restrict mc_raptor to not listen to the trajectory_setpoint (use the position and yaw at activation time as reference instead)

* bump RLtools; relax timing thresholds and adding real world readme

* smooth traj tracking performance

* Measuring trajectory_setpoint timing (providing stats in raptor_status); reverting accidental .gitignore modification

* More ideomatic way of setting the path to the policy checkpoint

* Reset trajectory_setpoint on raptor mode activation

* Adding internal trajectory generation (feeding trajectory_setpoint over Mavlink is too noisy). Quite agile trajectory tracking, good performance

* stable flight

* Update msg/versioned/RaptorInput.msg

Co-authored-by: Hamish Willee <hamishwillee@gmail.com>

* adopting message formatting conventions

* sort raptor.px4board

* Archiving RegisterExtComponentRequestV1.msg

* Add message versioning for VehicleStatus v2 and RegisterExtComponentRequest v2

* fixing formatting

* making internal reference configurable via command

* RAPTOR docs wip

* raptor internal reference documentation

* Finishing RAPTOR docs first draft

* adding logging instructions

* Fixing missing command documentation test error

* fixing format

* adding motor layout warning

* raptor minimal subedit - prettier, images etc

* Improve intro

* Fix up Neural_Networks version

* Mentioning "Adaptive" in the RAPTOR documentation's title

* Adding clarifications about the internal reference trajectory generator

* Removing "foundation policy" wording

* Fixing new-line check

* Removing redundant (evident through directory hierarchy) raptor_ from filenames

* Unifying Neural Network docs (mc_nn_control and mc_raptor) under the "Neural Network" topic

* Fix to standard structure

* Making the distinction between mc_nn_control and mc_raptor more clear and fixing the comparison table

* Removing trajectory_setpoint forwarding flag from external mode registration request and from the vehicle status

* Trivial layout and wording fixes

* fixing docs error

---------

Co-authored-by: Hamish Willee <hamishwillee@gmail.com>
2026-01-14 09:47:47 -08:00
b2672910da sbgecom: Implement sbgECom INS driver (#24137)
* Add new INS driver sbgECom

Implement sbgECom messages handling to provide IMU sensors, GNSS and EKF data to the autopilot
Be able to parametrize the serial port, baudrate and the communicating mode
Clone sbgECom library only if sbgecom support is enabled and apply a patch
Be able to send SBG Systems INS settings in several ways when starting sbgecom driver

* Fix sensor airspeed simulator units

* Fix HIGHRES_IMU pressure unit

* Allow HIGHRES_IMU to support 4 IMUs

* sbgECom: Add documentation

* Use submodule instead of fetching sbgECom using CMake

* Remove patch strategy

* Fix dates

* Remove patch file

* Update SBG dev type ID

Co-authored-by: Jacob Dahl <37091262+dakejahl@users.noreply.github.com>

---------

Co-authored-by: Samuel Toledano <samuel.toledano@sbg-systems.com>
Co-authored-by: Jacob Dahl <37091262+dakejahl@users.noreply.github.com>
2025-09-11 00:37:41 -08:00
Daniel Agar fb8c43efc3 gitmodules specificy branch for fuzztest and tflite_micro 2025-08-07 20:40:05 -04:00
Jacob Dahl ca3a1c77c4 fix submodule (#25368) 2025-08-05 20:41:31 -07:00
JoelJ18 b5e5d214fe drivers: MicroStrain Inertial Sensors (#23858) 2025-08-05 08:05:46 -07:00
3be0cb077c Neural Control Mode (#24366)
* Add tflm to px4 with module

 - Add TensorFlow Lite Micro(TFLM) as a library in px4
 - Make a module that uses neural network inference for control, which uses TFLM for inference
 - Make board config files for PX4 with neural module

* Added neural flight mode

* Add posibility to read of inference times

* Fix comments from review:

- Switch ssh link to https link in submodule
- Remove mc_nn_control from startup

* Add tflm to px4 with module

 - Add TensorFlow Lite Micro(TFLM) as a library in px4
 - Make a module that uses neural network inference for control, which uses TFLM for inference
 - Make board config files for PX4 with neural module

* Added neural flight mode

* Add posibility to read of inference times

* Remove auto start

* Add logging from neural control module

* Fix automatic startup to only be when module is included

* Switch to flight mode registration

* Add docs

* Change min/max/coeff to actual parameters

* add figures to neural network docs

* Switch to e2e network

* Remove toolchain changes and replace with instructions in docs

* Get ready for merge after toolchain upgrade

* switch back to submodule

* Try to figure out cmake

* Get CI working with new toolchain

* Remove fork dependency

* Finalize PR

* fix toolchain inclusion

* Fix ctype_base.h include

* Cleanup includes for TFLM

* Remove redundant std

* Update FW module names in board files

* Fix docs

* Remove cstdlib copy

* Copy header from nuttx

* Prettier, markup, layout

* NeuralControl.msg - update uorb comments to current standard

* Add description to neural topic

* Fix typo

* Typo

* TFLM and Module utitlities

* Neural networks top level

* Update docs

* Add manual control

* Update docs

* Revert the manual control attempt

* Update docs/en/advanced/nn_module_utilities.md

* Add posibility to set trajectory setpoint with manual control

---------

Co-authored-by: Pedro Roque <padr@kth.se>
Co-authored-by: Hamish Willee <hamishwillee@gmail.com>
Co-authored-by: Ramon Roche <mrpollo@gmail.com>
2025-07-25 09:42:12 -08:00
Beat Küng 3d1cace7b7 test: add google fuzztest to unit test build
From https://github.com/google/fuzztest.
This will now also add gtest (via cmake FetchContent)

And requires newer cmake (container updates):
CMake 3.19 or higher is required.  You are running version 3.16.3
2025-07-11 10:39:28 +02:00
Daniel Agar e59cc9afeb drivers/uavcan: subtree merge last working libuavcan (preserving history)
- upstream libuavcan was broken and then marked deprecated, this fully absorbs the submodule (renamed libdronecan to deconflict) up to our last good working commit and all commit history is kept
 - fixes https://github.com/PX4/PX4-Autopilot/issues/23727 (regression introduced in #23113)
 - this puts us in a much better position to evolve the library as needed now that we have full control
2024-10-16 13:31:17 -04:00
vertiq-jordanandLuca Scheuer 06dfc4b782 drivers/actuators: new vertiq_io driver (#22892)
* brought in the Vertiq Cpp API as a submodule. updated the serial rx handling so that we can parse out IQUART data packets

---------

Co-authored-by: Luca Scheuer <scheuer.luca@gmail.com>
2024-09-24 11:44:35 -04:00
Alexis Paques abc629c2bb zenoh: update zenoh-pico from 0.7.0 to 1.0.0 (#23462)
* Update Zenoh-pico from 0.7.0 to 1.0.0
* Update the zenoh-pico version to use PX4/dev/1.0.0-px4
* Remove the rostopic and rt/ prefix
 * Unlike zenoh-bridge-dds we were using, zenoh-bridge-ros2dds is now adding the rt/ prefix automagically.
2024-08-02 11:48:55 -04:00
Eric Katzfey 4a553938fb VOXL2: HRT updates for synchronization with Qurt time (#22881)
- Added offset to Posix hrt time to account for synchronization with Qurt hrt time
- Added new Kconfig to configure synchronization of HRT timestamps on VOXL2
- Moved voxl2 libfc sensor library submodule from muorb module to boards directory
- Added check to make sure hrt_elapsed_time can never be negative
2024-03-22 15:24:51 -04:00
Eric Katzfey 2b69a3d290 VOXL2 specific drivers, modules, and miscellaneous support files (#22588) 2024-01-18 12:14:17 -05:00
Daniel Agar 855bf8f0d2 .gitmodules set gz submodule branch 2024-01-11 11:07:33 -05:00
65e53286b6 Standalone px4 stable (#22467)
simulation gazebo: move the gazebo models to submodule, allow for operation with external gazebo instance, independent of startup order. Allows drag an drop of models from gazebo fuel.

* rolled back updates

Signed-off-by: frederik <frederik@auterion.com>

* fixing empy

Signed-off-by: frederik <frederik@auterion.com>

* Update GZBridge.cpp to lower drop position 

Dropping from 1m leads to movement in the rc_cessna. Dropping from 0.5m leads to no movement.

* Update STANDALONE env variable.

* Update STANDALONE env_variable on GZBridge

* Update src/modules/simulation/gz_bridge/GZBridge.cpp

Co-authored-by: Daniel Agar <daniel@agar.ca>

* test removal of x500

Signed-off-by: frederik <frederik.anilmarkus@gmail.com>

* removed all models and reworked logic

Signed-off-by: frederik <frederik.anilmarkus@gmail.com>

* remove model path in set_sdf_filename

Signed-off-by: frederik <frederik.anilmarkus@gmail.com>

* filter resource path for world sdf

Signed-off-by: frederik <frederik.anilmarkus@gmail.com>

* updated structure to keep old make px4_sitl

Signed-off-by: frederik <frederik.anilmarkus@gmail.com>

* remove gz tools

Signed-off-by: frederik <frederik.anilmarkus@gmail.com>

* import gz as submodule and reverse rc simulator logic

Signed-off-by: frederik <frederik.anilmarkus@gmail.com>

* [gz-sim]: source GZ_SIM_RESOURCE_PATH only if PX4 starts gz server

Signed-off-by: Beniamino Pozzan <beniamino.pozzan@gmail.com>

* Typo fix

---------

Signed-off-by: frederik <frederik@auterion.com>
Signed-off-by: frederik <frederik.anilmarkus@gmail.com>
Signed-off-by: Beniamino Pozzan <beniamino.pozzan@gmail.com>
Co-authored-by: Daniel Agar <daniel@agar.ca>
Co-authored-by: Beniamino Pozzan <beniamino.pozzan@gmail.com>
2023-12-18 09:43:20 +01:00
Daniel Agar 1592aedc11 gitmodules add heatshrink branch 2023-11-10 17:45:47 -05:00
Beat Küng 1ad5a9de08 uorb: compress format definitions
Reduces flash usage by ~16KB.

- compress formats at build-time into a single string with all formats
- then at runtime iteratively decompress using
  https://github.com/atomicobject/heatshrink
2023-11-08 00:31:26 -05:00
Peter van der Perk 019d232911 Add Zenoh pico support 2023-10-18 15:30:36 -04:00
Beniamino Pozzan 9e5420bbbd microdds_client: rename to uxrce_dds_client
| | old version | new version (second proposal) |
|-|-|-|
| module name | `microdds_client` | **`uxrce_dds_client`** |
| strings / comments about the module | non consistent | **UXRCE-DDS Client** |
| menuconfig option | `MODULES_MICRODDS_CLIENT` | **`MODULES_UXRCE_DDS_CLIENT`** |
| module parameters group name | `Micro XRCE-DDS` | **UXRCE-DDS Client** |
| module parameters name prefix | `XRCE_DDS_` | `UXRCE_DDS_` |
| module class name | `MicroddsClient` | **`UxrceddsClient`** |
|`init.d/rcS` whenever the module is mentioned | `microdds` | **`uxrce_dds`** |
| main doc page name | XRCE-DDS (PX4-FastDDS Bridge) | **uXRCE-DDS (PX4-micro XRCE-DDS Bridge)**|
| environment variable to have custom namespace in simulation | PX4_MICRODDS_NS | **PX4_UXRCE_DDS_NS** |

Signed-off-by: Beniamino Pozzan <beniamino.pozzan@phd.unipd.it>
2023-05-03 11:51:53 -07:00
Daniel Agar 6991ac014c rename 'gazebo' simulation to 'gazebo-classic' (#20936)
- use `gazebo-classic` everywhere consistently referring to the original Gazebo (eg version 9,10,11)
   - additional `gazebo_*` helper targets added for compatibility, but warn about deprecation and tell you the new target naming
 - use `gz` everywhere when referring to Gazebo (aka Ignition Gazebo or new Gazebo)
2023-01-15 11:36:12 -05:00
Daniel Agar 4f99ac209c gitmodules update NuttX to 10.3.0+ 2022-12-06 18:40:58 -05:00
Daniel Agar cea185268e msg ROS2 compatibility, microdds_client improvements (timesync, reduced code size, added topics, etc), fastrtps purge
- update all msgs to be directly compatible with ROS2
 - microdds_client improvements
   - timesync
   - reduced code size
   - add to most default builds if we can afford it
   - lots of other little changes
 - purge fastrtps (I tried to save this multiple times, but kept hitting roadblocks)
2022-10-19 19:36:47 -04:00
Daniel Agar 2bd1ac005f .gitmodules update branches master -> main 2022-10-01 12:22:22 -04:00
Daniel Agar 4040e4cdf2 simulation organization and cleanup
- new modules/simulation directory to collect all simulators and related modules
 - new Tools/simulation directory to collect and organize scattered simulation submodules, scripts, etc
 - simulation module renamed to simulator_mavlink
 - sih renamed to simulator_sih (not a great name, but I wanted to be clear it was a simulator)
 - ignition_simulator renamed to simulator_ignition_bridge
 - large sitl_target.cmake split by simulation option and in some cases pushed to appropriate modules
 - sitl targets broken down to what's actually available (eg jmavsim only has 1 model and 1 world)
 - new Gazebo consistently referred to as Ignition for now (probably the least confusing thing until we fully drop Gazebo classic support someday)
2022-08-25 09:10:03 -04:00
Daniel AgarandJaeyoung-Lim cfc579542e new Ignition Gazebo simulation interface architecture (#20057)
- much simpler direct interface using Ignition Transport 
 - in tree models and worlds
 - control allocation output configuration, no more magic actuator mapping to mavlink and back
 - currently requires no custom Gazebo plugins (keeping things as lightweight and simple as possible)

Co-authored-by: Jaeyoung-Lim <jalim@ethz.ch>
2022-08-22 10:58:19 -04:00
Peter van der Perk b1ad4e8864 Upgrade libcanard to 3.0 and rename uavcan_v1 to cyphal
Did some prep work for redundant interfaces by introducing CanardHandle class to decouple physical interfaces from cyphal.cpp
2022-05-10 09:46:18 -04:00
Daniel Mesham 06a9be74fa microdds: add xrce client 2022-03-22 09:01:05 +01:00
Daniel Agar 9c09983f73 update dsdl submodule to latest and fix branch 2021-12-16 12:10:55 +11:00
Peter van der Perk ce10dd90e7 Remove ucannode_gps_demo since it's superseded by uavcan_v1 2021-12-01 09:29:15 -05:00
Daniel Agar 38516f7e9c delete matrix submodule 2021-11-16 12:20:57 -05:00
Jacob Crabill 5969508fa7 mavlink: cmake generate mavlink headers at build time
- mavlink/mavlink is now directly included as a submodule instead of the generated mavlink/c_library_v2
 - this also switches to mavlink development.xml by default
2021-11-05 23:01:38 -04:00
Daniel Agar c73a1b4c68 update UAVCAN-v0 dsdl to DroneCAN 2021-11-04 21:36:13 -04:00
Daniel Agar 0cfba10e5b switch to DroneCAN for DSDL and pyuavcan 2021-10-20 21:43:43 -04:00
Jukka Laitinen 40063bd54b Add libtomcrypt and libtommath submodules
These provide e.g. rsa_oaep, which can be used for sw crypto

Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
2021-09-27 17:45:07 +02:00
Daniel Agar 31545f85fb gitmodules update NuttX branches to latest v10.1.0 2021-08-19 13:02:31 -04:00
JaeyoungLim 58060b23d9 Add ignition gazebo support for PX4 Software-In-The-Loop simulations
This commit adds SITL support for ignition gazebo. Ignition gazebo is a replacement for the "classic" gazebo for future applications.

The simulation can be run as the following
```
make px4_sitl ignition
```
2021-07-19 19:59:41 -04:00
Daniel Agar 65745a3676 purge broken qurt support and atlflight boards 2021-07-16 08:53:36 -04:00
Daniel Agar cd1e04d034 delete ecl submodule 2021-07-13 09:54:02 -04:00
Daniel Agar 23688d8234 monocypher submodule point to px4 branch 2021-07-08 13:54:34 -04:00
Beat Küng 38f3b8d356 mavlink & system: add events interface
- sending protocol
- uorb event message & template methods for argument packing
- libevents submodule to send common events and handle json files
- cmake maintains a list of all (PX4) source files for the current build
  (PX4 modules + libs), which is used to extract event metadata and
  generate a json file
2021-07-07 21:38:09 -04:00
Jukka Laitinen b3e9904df0 Add monocypher crypto library in src/lib/crypto/monocypher
This simple crypto library is used as an example default backend for the crypto
interfaces

Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
2021-06-25 08:35:58 +02:00
Jukka Laitinen 12f33524fa fix legacy data types again
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
2021-05-28 17:55:02 -04:00
Jukka Laitinen 0de0709be3 Fix github url for uavcan_v1/legacy_data_types
The URL is spelled wrong, it should be capital "PX4"

Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
2021-05-28 10:36:30 -04:00
Peter van der Perk 24c2967511 legacy_data_types specify branch 2021-05-04 13:23:14 -04:00
TSC21 18dc0e4900 update submodule micro-CDR 2021-05-02 13:05:16 -04:00