mirror of
https://github.com/PX4/PX4-Autopilot.git
synced 2026-11-22 22:31:04 +08:00
170 lines
7.7 KiB
Markdown
170 lines
7.7 KiB
Markdown
# 硬体仿真(HITL)
|
|
|
|
:::warning
|
|
硬体仿真被 [社区支持和维护](../simulation/community_supported_simulators.md)
|
|
It may or may not work with current versions of PX4.
|
|
|
|
See [Toolchain Installation](../dev_setup/dev_env.md) for information about the environments and tools supported by the core development team.
|
|
:::
|
|
|
|
硬件在环仿真模式 (HITL 或 HIL) 下 PX4 固件代码运行在真实的飞行控制器硬件平台上。这种方法的优点是可以在实际硬件上测试大多数的实际飞行代码。
|
|
|
|
PX4 supports HITL for multicopters and VTOL using [Gazebo Classic](../sim_gazebo_classic/index.md).
|
|
To simulate on flight controller hardware without an external simulator, use [SIH on hardware](../sim_sih/hardware.md).
|
|
|
|
For a comparison of HITL and SIH on hardware, see [Hardware Simulation](../simulation/hardware.md).
|
|
|
|
## HITL-Compatible Airframes {#compatible_airframe}
|
|
|
|
机架与模拟器兼容情况:
|
|
|
|
| 机架 | `SYS_AUTOSTART` | Gazebo Classic |
|
|
| ---------------------------------------------------------------------------------------------------------------- | --------------- | -------------- |
|
|
| [HIL Quadcopter X](../airframes/airframe_reference.md#copter_simulation_hil_quadcopter_x) | 1002 | Y |
|
|
| [HIL Standard VTOL QuadPlane](../airframes/airframe_reference.md#vtol_standard_vtol_hil_standard_vtol_quadplane) | 4001 | Y |
|
|
|
|
## HITL Simulation Environment {#simulation_environment}
|
|
|
|
硬件在环仿真(HITL)模式下标准的 PX4 固件在真实的硬件上运行。
|
|
Gazebo Classic (running on a development computer) is connected to the flight controller hardware via USB/UART.
|
|
The simulator acts as gateway to share MAVLink data between PX4 and _QGroundControl_.
|
|
|
|
:::info
|
|
The simulator can also be connected via UDP if the flight controller has networking support and uses a stable, low-latency connection (e.g. a wired Ethernet connection - WiFi is usually not sufficiently reliable).
|
|
For example, this configuration has been tested with PX4 running on a Raspberry Pi connected via Ethernet to the computer (the startup configuration can be found in [px4_hil.config](https://github.com/PX4/PX4-Autopilot/blob/main/posix-configs/rpi/px4_hil.config)).
|
|
:::
|
|
|
|
The diagram below shows the simulation environment:
|
|
|
|
- A HITL configuration is selected (via _QGroundControl_) that doesn't start any real sensors.
|
|
- _Gazebo Classic_ is connected to the flight controller via USB.
|
|
- The simulator is connected to _QGroundControl_ via UDP and bridges its MAVLink messages to PX4.
|
|
- _Gazebo Classic_ can also connect to an offboard API and bridge MAVLink messages to PX4.
|
|
- (Optional) A serial connection can be used to connect Joystick/Gamepad hardware via _QGroundControl_.
|
|
|
|

|
|
|
|
## HITL 相比于 SITL
|
|
|
|
相比之下, HITL 在正常飞控硬件平台上运行正常的处于 ”HITL 模式“ 的 PX4 固件。仿真数据进入整个仿真系统的时间点与 SITL 有所不同。
|
|
|
|
By contrast, HITL runs normal PX4 firmware in "HITL mode", on normal hardware.
|
|
The simulation data enters the system at a different point than for SITL.
|
|
Core modules like commander and sensors have HITL modes at startup that bypass some of the normal functionality.
|
|
|
|
完成所有的配置设定后 <strong x-id="1">关闭</strong> <em x-id="3">QGroundControl</em> 并断开飞控板与计算机的连接。
|
|
|
|
## 配置 HITL
|
|
|
|
## Check if HITL is in Firmware
|
|
|
|
The module required for HITL ([`pwm_out_sim`](../modules/modules_driver.md#pwm-out-sim)) is not built into all PX4 firmware by default.
|
|
|
|
To check if the module is present on your Flight Controller:
|
|
|
|
1. Open QGroundControl
|
|
|
|
2. Open **Analyze Tools > Mavlink Console**.
|
|
|
|
3. Type the following command in the console:
|
|
|
|
```sh
|
|
pwm_out_sim status
|
|
```
|
|
|
|
4. If the returned value is `nsh: pwm_out_sim: command not found`, then you don't have the module installed.
|
|
|
|
If `pwm_out_sim` is not present you will need to add it to the firmware in order to use HITL simulation.
|
|
|
|
### Adding HITL modules to the Firmware
|
|
|
|
Add the following key to the configuration file for your flight controller to include the required module (for an example see [boards/px4/fmu-v6x/default.px4board](https://github.com/PX4/PX4-Autopilot/blob/main/boards/px4/fmu-v6x/default.px4board)).
|
|
Then re-build the firmware and flash it to the board.
|
|
|
|
```text
|
|
CONFIG_MODULES_SIMULATION_PWM_OUT_SIM=y
|
|
```
|
|
|
|
You can alternatively use the following command to launch a GUI configuration tool, and interactively enable them at the path: **modules > Simulation > pwm_out_sim**.
|
|
For example, to update fmu-v6x you would use:
|
|
|
|
```sh
|
|
make px4_fmu-v6x boardconfig
|
|
```
|
|
|
|
### PX4 配置
|
|
|
|
1. Connect the autopilot directly to _QGroundControl_ via USB.
|
|
|
|
2. 选择机架
|
|
1. Open **Setup > Airframes**
|
|
2. Select a [compatible airframe](#compatible_airframe) you want to test.
|
|
Then click **Apply and Restart** on top-right of the _Airframe Setup_ page.
|
|
|
|
3. Calibrate your [Manual Controller](../config/manual_control.md) (RC or Joystick), if needed.
|
|
|
|
4. 设置 UDP
|
|
1. Under the _General_ tab of the settings menu, uncheck all _AutoConnect_ boxes except for **UDP**.
|
|
|
|

|
|
|
|
5. (Optional) Configure your manual controller priority and failsafe:
|
|
|
|
- [Enable a mode in `COM_RC_IN_MODE` that enables and prioritises the controllers you want to use](../config/manual_control.md#px4-configuration).
|
|
The default `RC or MAVLink keep first` should work if you plan to only have a Joystick (no RC).
|
|
- You can set [NAV_RCL_ACT](../advanced_config/parameter_reference.md#NAV_RCL_ACT) to disable manual control loss failsafe while flying in a simulation.
|
|
|
|
:::tip
|
|
The _QGroundControl User Guide_ also has instructions on [Joystick](https://docs.qgroundcontrol.com/master/en/qgc-user-guide/setup_view/joystick.html) and [Virtual Joystick](https://docs.qgroundcontrol.com/master/en/qgc-user-guide/settings_view/virtual_joystick.html) setup.
|
|
|
|
:::
|
|
|
|
Once configuration is complete, **close** _QGroundControl_ and disconnect the flight controller hardware from the computer.
|
|
|
|
### X-Plane HITL 仿真环境
|
|
|
|
总而言之, HITL 在真实硬件上运行标准 PX4 固件,而 SITL 实际上要比标准 PX4 系统执行更多的代码。
|
|
|
|
#### Gazebo Classic
|
|
|
|
:::info
|
|
Make sure _QGroundControl_ is not running!
|
|
:::
|
|
|
|
1. Build PX4 with [Gazebo Classic](../sim_gazebo_classic/index.md) (in order to build the Gazebo Classic plugins).
|
|
|
|
```sh
|
|
cd <PX4-Autopilot clone>
|
|
DONT_RUN=1 make px4_sitl_default gazebo-classic
|
|
```
|
|
|
|
2. Open the vehicle model's sdf file (e.g. **Tools/simulation/gazebo-classic/sitl_gazebo-classic/models/iris_hitl/iris_hitl.sdf**).
|
|
|
|
3. Replace the `serialDevice` parameter (`/dev/ttyACM0`) if necessary.
|
|
|
|
::: info
|
|
The serial device depends on what port is used to connect the vehicle to the computer (this is usually `/dev/ttyACM0`).
|
|
An easy way to check on Ubuntu is to plug in the autopilot, open up a terminal, and type `dmesg | grep "tty"`.
|
|
The correct device will be the last one shown.
|
|
|
|
:::
|
|
|
|
4. Set up the environment variables:
|
|
|
|
```sh
|
|
source Tools/simulation/gazebo-classic/setup_gazebo.bash $(pwd) $(pwd)/build/px4_sitl_default
|
|
```
|
|
|
|
and run Gazebo Classic in HITL mode:
|
|
|
|
```sh
|
|
gazebo Tools/simulation/gazebo-classic/sitl_gazebo-classic/worlds/hitl_iris.world
|
|
```
|
|
|
|
5. Start _QGroundControl_.
|
|
It should autoconnect to PX4 and Gazebo Classic.
|
|
|
|
## 在 HITL 仿真中执行自主飞行任务
|
|
|
|
You should be able to use _QGroundControl_ to [run missions](https://docs.qgroundcontrol.com/master/en/qgc-user-guide/fly_view/fly_view.html#missions) and otherwise control the vehicle.
|