Files
PX4-Autopilot/docs/en/modules/modules_driver_ins.md
T
Alex E 59fa7a4a7d docs(modules): add auto-generated disclaimer to every module reference page (#29673)
Only modules_main.md told readers that the module reference is generated
from source. The per-category pages (modules_driver.md, modules_system.md,
...) and the per-subcategory pages (modules_driver_imu.md, ...) had no such
note, so contributors kept fixing typos directly in docs/en/modules/ and
the next metadata sync silently reverted them (see #29614).

Emit a `::: info` block right under the H1 of every category and
subcategory page. The wording follows the existing disclaimers on the
airframe reference and the uORB message index: it links to the generator
script and names the `make module_documentation` target.

docs/en/modules/*.md are regenerated with the updated generator and run
through Prettier, mirroring what the docs-orchestrator metadata sync does
on main, so the diff is only the new note.

Fixes #29624

Assisted-by: Claude:claude-fable-5-1

Signed-off-by: Alex E <aelejandro9@gmail.com>
2026-11-10 08:51:33 +11:00

194 lines
4.4 KiB
Markdown

# Modules Reference: Ins (Driver)
::: info
**This page is [auto-generated](https://github.com/PX4/PX4-Autopilot/blob/main/Tools/px4moduledoc/markdownout.py) from the source code** using the build command: `make module_documentation`.
Do not edit it directly; fix the module documentation in the [PX4-Autopilot](https://github.com/PX4/PX4-Autopilot) source instead.
:::
## MicroStrain
Source: [drivers/ins/microstrain](https://github.com/PX4/PX4-Autopilot/tree/main/src/drivers/ins/microstrain)
### Description
MicroStrain by HBK Inertial Sensor Driver.
Currently supports the following sensors:
-[CV7-AR](https://www.hbkworld.com/en/products/transducers/inertial-sensors/vertical-reference/3dm-cv7-ar) -[CV7-AHRS](https://www.hbkworld.com/en/products/transducers/inertial-sensors/attitude-and-heading/3dm-cv7-ahrs) -[CV7-INS](https://www.hbkworld.com/en/products/transducers/inertial-sensors/navigation/3dm-cv7-ins) -[CV7-GNSS/INS](https://www.hbkworld.com/en/products/transducers/inertial-sensors/navigation/3dm-cv7-gnss-ins)
This driver is not included in the firmware by default.
Include the module in firmware by setting the
[kconfig](../hardware/porting_guide_config.md#px4-board-configuration-kconfig) variables:
`CONFIG_DRIVERS_INS_MICROSTRAIN` or `CONFIG_COMMON_INS`.
### Examples
Attempt to start driver on a specified serial device.
The driver will choose /dev/ttyS4 by default if no port is specified
```
microstrain start -d /dev/ttyS1
```
Stop driver
```
microstrain stop
```
### Usage {#MicroStrain_usage}
```
MicroStrain <command> [arguments...]
Commands:
start Start driver
[-d <val>] Port
values: <file:dev>, default: /dev/ttyS4
stop Stop driver
status Driver status
```
## eulernav_bahrs
Source: [drivers/ins/eulernav_bahrs](https://github.com/PX4/PX4-Autopilot/tree/main/src/drivers/ins/eulernav_bahrs)
### Description
Serial bus driver for the EULER-NAV Baro-Inertial AHRS.
### Examples
Attempt to start driver on a specified serial device.
```
eulernav_bahrs start -d /dev/ttyS1
```
Stop driver
```
eulernav_bahrs stop
```
### Usage {#eulernav_bahrs_usage}
```
eulernav_bahrs <command> [arguments...]
Commands:
start Start driver
-d <val> Serial device
status Print driver status
stop Stop driver
```
## ilabs
Source: [drivers/ins/ilabs](https://github.com/PX4/PX4-Autopilot/tree/main/src/drivers/ins/ilabs)
### Description
Serial bus driver for the ILabs sensors.
Most boards are configured to enable/start the driver on a specified UART using the SENS_ILABS_CFG.
After that you can use the ILABS_MODE parameter to config outputs:
- Only raw sensor output (the default).
- Sensor output and INS data such as position and velocity estimates.
Setup/usage information: https://docs.px4.io/main/en/sensor/inertiallabs.html
### Examples
Attempt to start driver on a specified serial device.
```
ilabs start -d /dev/ttyS1
```
Stop driver
```
ilabs stop
```
### Usage {#ilabs_usage}
```
ilabs <command> [arguments...]
Commands:
start Start driver
-d <val> Serial device
status Driver status
stop Stop driver
```
## sbgecom
Source: [drivers/ins/sbgecom](https://github.com/PX4/PX4-Autopilot/tree/main/src/drivers/ins/sbgecom)
Description du module
### Usage {#sbgecom_usage}
```
sbgecom <command> [arguments...]
Commands:
start Start driver
[-d <val>] Serial device
default: /dev/ttyS0
[-b <val>] Baudrate device
default: 921600
[-f <val>] Config JSON file path
default: /etc/extras/sbg_settings\.json
[-s <val>] Config JSON string
status Driver status
stop Stop driver
```
## vectornav
Source: [drivers/ins/vectornav](https://github.com/PX4/PX4-Autopilot/tree/main/src/drivers/ins/vectornav)
### Description
Serial bus driver for the VectorNav VN-100, VN-200, VN-300.
Most boards are configured to enable/start the driver on a specified UART using the SENS_VN_CFG parameter.
Setup/usage information: https://docs.px4.io/main/en/sensor/vectornav.html
### Examples
Attempt to start driver on a specified serial device.
```
vectornav start -d /dev/ttyS1
```
Stop driver
```
vectornav stop
```
### Usage {#vectornav_usage}
```
vectornav <command> [arguments...]
Commands:
start Start driver
-d <val> Serial device
status Driver status
stop Stop driver
```