Files
2026-10-23 20:56:40 +00:00

183 KiB

pageClass
pageClass
is-wide-page

VehicleCommandV0 (UORB message)

Vehicle Command uORB message. Used for commanding a mission / action / etc. Follows the MAVLink COMMAND_INT / COMMAND_LONG definition.

TOPICS: vehicle_command gimbal_v1_command vehicle_command_mode_executor

Fields

Name Type Unit [Frame] Range/Enum Description
timestamp uint64 us Time since system start.
param1 float32 Parameter 1, as defined by MAVLink uint16 VEHICLE_CMD enum.
param2 float32 Parameter 2, as defined by MAVLink uint16 VEHICLE_CMD enum.
param3 float32 Parameter 3, as defined by MAVLink uint16 VEHICLE_CMD enum.
param4 float32 Parameter 4, as defined by MAVLink uint16 VEHICLE_CMD enum.
param5 float64 Parameter 5, as defined by MAVLink uint16 VEHICLE_CMD enum.
param6 float64 Parameter 6, as defined by MAVLink uint16 VEHICLE_CMD enum.
param7 float32 Parameter 7, as defined by MAVLink uint16 VEHICLE_CMD enum.
command uint32 Command ID.
target_system uint8 System which should execute the command.
target_component uint8 Component which should execute the command, 0 for all components.
source_system uint8 System sending the command.
source_component uint16 Component / mode executor sending the command.
confirmation uint8 0: First transmission of this command. 1-255: Confirmation transmissions (e.g. for kill command).
from_external bool

Constants

Name Type Value Description
MESSAGE_VERSION uint32 0
VEHICLE_CMD_CUSTOM_0 uint16 0 Test command.
VEHICLE_CMD_CUSTOM_1 uint16 1 Test command.
VEHICLE_CMD_CUSTOM_2 uint16 2 Test command.
VEHICLE_CMD_NAV_WAYPOINT uint16 16 Navigate to MISSION. [s] (decimal) Hold time. (ignored by fixed wing, time to stay at MISSION for rotary wing) [m] Acceptance radius (if the sphere with this radius is hit, the MISSION counts as reached) 0 to pass through the WP, if > 0 radius [m] to pass by WP. Positive value for clockwise orbit, negative value for counter-clockwise orbit. Allows trajectory control. Desired yaw angle at MISSION (rotary wing) Latitude Longitude Altitude
VEHICLE_CMD_NAV_LOITER_UNLIM uint16 17 Loiter around this MISSION an unlimited amount of time. Unused Unused [m] Radius around MISSION. If positive loiter clockwise, else counter-clockwise Desired yaw angle. Latitude Longitude Altitude
VEHICLE_CMD_NAV_LOITER_TURNS uint16 18 Loiter around this MISSION for X turns. Turns Unused Radius around MISSION [m]. If positive loiter clockwise, else counter-clockwise Desired yaw angle. Latitude Longitude Altitude
VEHICLE_CMD_NAV_LOITER_TIME uint16 19 Loiter around this MISSION for time. [s] Seconds (decimal) Unused Radius around MISSION [m]. If positive loiter clockwise, else counter-clockwise Desired yaw angle. Latitude Longitude Altitude
VEHICLE_CMD_NAV_RETURN_TO_LAUNCH uint16 20 Return to launch location. Unused Unused Unused Unused Unused Unused Unused
VEHICLE_CMD_NAV_LAND uint16 21 Land at location. Unused Unused Unused Desired yaw angle. Latitude Longitude Altitude
VEHICLE_CMD_NAV_TAKEOFF uint16 22 Takeoff from ground / hand. Unused (FW pitch from FW_TKO_PITCH_MIN) Unused Unused [deg] [@range 0,360] Yaw angle in NED if yaw source available, ignored otherwise Latitude (WGS-84) Longitude (WGS-84) [m] Altitude AMSL
VEHICLE_CMD_NAV_PRECLAND uint16 23 Attempt a precision landing.
VEHICLE_CMD_DO_ORBIT uint16 34 Start orbiting on the circumference of a circle defined by the parameters. [m] Radius [m/s] Velocity [@enum ORBIT_YAW_BEHAVIOUR] Yaw behaviour Unused Latitude/X Longitude/Y Altitude/Z
VEHICLE_CMD_DO_FIGUREEIGHT uint16 35 Start flying on the outline of a figure eight defined by the parameters. [m] Major radius [m] Minor radius [m/s] Velocity Orientation Latitude/X Longitude/Y Altitude/Z
VEHICLE_CMD_NAV_ROI uint16 80 Sets the region of interest (ROI) for a sensor set or the vehicle itself. This can then be used by the vehicles control system to control the vehicle attitude and the attitude of various sensors such as cameras. [@enum VEHICLE_ROI] Region of interest mode. MISSION index/ target ID. ROI index (allows a vehicle to manage multiple ROI's) Unused x the location of the fixed ROI (see MAV_FRAME) y z
VEHICLE_CMD_NAV_PATHPLANNING uint16 81 Control autonomous path planning on the MAV. 0: Disable local obstacle avoidance / local path planning (without resetting map), 1: Enable local path planning, 2: Enable and reset local path planning 0: Disable full path planning (without resetting map), 1: Enable, 2: Enable and reset map/occupancy grid, 3: Enable and reset planned route, but not occupancy grid Unused [deg] [@range 0, 360] Yaw angle at goal, in compass degrees Latitude/X of goal Longitude/Y of goal Altitude/Z of goal
VEHICLE_CMD_NAV_VTOL_TAKEOFF uint16 84 Takeoff from ground / hand and transition to fixed wing. Minimum pitch (if airspeed sensor present), desired pitch without sensor Transition heading, 0: Default, 3: Use specified transition heading Unused Yaw angle (if magnetometer present), ignored without magnetometer Latitude Longitude Altitude
VEHICLE_CMD_NAV_VTOL_LAND uint16 85 Transition to MC and land at location. Unused Unused Unused Desired yaw angle. Latitude Longitude Altitude
VEHICLE_CMD_NAV_GUIDED_LIMITS uint16 90 Set limits for external control. [s] Timeout - maximum time that external controller will be allowed to control vehicle. 0 means no timeout [m] Absolute altitude min AMSL - if vehicle moves below this alt, the command will be aborted and the mission will continue. 0 means no lower altitude limit [m] Absolute altitude max - if vehicle moves above this alt, the command will be aborted and the mission will continue. 0 means no upper altitude limit [m] Horizontal move limit (AMSL) - if vehicle moves more than this distance from it's location at the moment the command was executed, the command will be aborted and the mission will continue. 0 means no horizontal altitude limit Unused Unused Unused
VEHICLE_CMD_NAV_GUIDED_MASTER uint16 91 Set id of master controller. System ID Component ID Unused Unused Unused Unused Unused
VEHICLE_CMD_NAV_DELAY uint16 93 Delay the next navigation command a number of seconds or until a specified time. [s] Delay (decimal, -1 to enable time-of-day fields) [h] hour (24h format, UTC, -1 to ignore) minute (24h format, UTC, -1 to ignore) second (24h format, UTC) Unused Unused Unused
VEHICLE_CMD_NAV_LAST uint16 95 NOP - This command is only used to mark the upper limit of the NAV/ACTION commands in the enumeration. Unused Unused Unused Unused Unused Unused Unused
VEHICLE_CMD_CONDITION_DELAY uint16 112 Delay mission state machine. [s] Delay (decimal seconds) Unused Unused Unused Unused Unused Unused
VEHICLE_CMD_CONDITION_CHANGE_ALT uint16 113 Ascend/descend at rate. Delay mission state machine until desired altitude reached. Descent / Ascend rate (m/s) Unused Unused Unused Unused Unused Finish Altitude
VEHICLE_CMD_CONDITION_DISTANCE uint16 114 Delay mission state machine until within desired distance of next NAV point. Distance [m] Unused Unused Unused Unused Unused Unused
VEHICLE_CMD_CONDITION_YAW uint16 115 Reach a certain target angle. [deg] [@range 0,360] Target angle. 0 is north [deg/s] Speed during yaw change [@range -1,1] Direction: negative: counter clockwise, positive: clockwise [ 1,0] Relative offset or absolute angle Unused Unused Unused
VEHICLE_CMD_CONDITION_LAST uint16 159 NOP - This command is only used to mark the upper limit of the CONDITION commands in the enumeration. Unused Unused Unused Unused Unused Unused Unused
VEHICLE_CMD_CONDITION_GATE uint16 4501 Wait until passing a threshold. 2D coord mode: 0: Orthogonal to planned route Altitude mode: 0: Ignore altitude Unused Unused Lat Lon Alt
VEHICLE_CMD_DO_SET_MODE uint16 176 Set system mode. Mode, as defined by ENUM MAV_MODE Unused Unused Unused Unused Unused Unused
VEHICLE_CMD_DO_JUMP uint16 177 Jump to the desired command in the mission list. Repeat this action only the specified number of times. Sequence number Repeat count Unused Unused Unused Unused Unused
VEHICLE_CMD_DO_CHANGE_SPEED uint16 178 Change speed and/or throttle set points. [@enum SPEED_TYPE] Speed type (0=Airspeed, 1=Ground Speed) Speed (m/s, -1 indicates no change) [%] Throttle ( Percent, -1 indicates no change) Unused Unused Unused Unused
VEHICLE_CMD_DO_SET_HOME uint16 179 Changes the home location either to the current location or a specified location. Use current (1=use current location, 0=use specified location) Unused Unused Unused Latitude Longitude Altitude
VEHICLE_CMD_DO_SET_PARAMETER uint16 180 Set a system parameter. Caution! Use of this command requires knowledge of the numeric enumeration value of the parameter. Parameter number Parameter value Unused Unused Unused Unused Unused
VEHICLE_CMD_DO_SET_RELAY uint16 181 Set a relay to a condition. Relay number Setting (1=on, 0=off, others possible depending on system hardware) Unused Unused Unused Unused Unused
VEHICLE_CMD_DO_REPEAT_RELAY uint16 182 Cycle a relay on and off for a desired number of cycles with a desired period. Relay number Cycle count [s] Cycle time (decimal seconds) Unused Unused Unused Unused
VEHICLE_CMD_DO_REPEAT_SERVO uint16 184 Cycle a between its nominal setting and a desired PWM for a desired number of cycles with a desired period. Servo number [us] PWM rate (1000 to 2000 typical) Cycle count [s] Cycle time Unused Unused Unused
VEHICLE_CMD_DO_FLIGHTTERMINATION uint16 185 Terminate flight immediately. Flight termination activated if > 0.5 Unused Unused Unused Unused Unused Unused
VEHICLE_CMD_DO_CHANGE_ALTITUDE uint16 186 Set the vehicle to Loiter mode and change the altitude to specified value. Altitude Frame of new altitude Unused Unused Unused Unused Unused
VEHICLE_CMD_DO_SET_ACTUATOR uint16 187 Sets actuators (e.g. servos) to a desired value. Actuator 1 Actuator 2 Actuator 3 Actuator 4 Actuator 5 Actuator 6 Index
VEHICLE_CMD_DO_LAND_START uint16 189 Mission command to perform a landing. This is used as a marker in a mission to tell the autopilot where a sequence of mission items that represents a landing starts. It may also be sent via a COMMAND_LONG to trigger a landing, in which case the nearest (geographically) landing sequence in the mission will be used. The Latitude/Longitude is optional, and may be set to 0/0 if not needed. If specified then it will be used to help find the closest landing sequence. Unused Unused Unused Unused Latitude Longitude Unused
VEHICLE_CMD_DO_GO_AROUND uint16 191 Mission command to safely abort an autonomous landing. [m] Altitude Unused Unused Unused Unused Unused Unused
VEHICLE_CMD_DO_REPOSITION uint16 192 Reposition to specific WGS84 GPS position. [m/s] Ground speed Bitmask [m] Loiter radius for planes [deg] Yaw Latitude Longitude Altitude
VEHICLE_CMD_DO_PAUSE_CONTINUE uint16 193
VEHICLE_CMD_DO_SET_ROI_LOCATION uint16 195 Sets the region of interest (ROI) to a location. This can then be used by the vehicles control system to control the vehicle attitude and the attitude of various sensors such as cameras. Unused Unused Unused Unused Latitude Longitude Altitude
VEHICLE_CMD_DO_SET_ROI_WPNEXT_OFFSET uint16 196 Sets the region of interest (ROI) to be toward next waypoint, with optional pitch/roll/yaw offset. This can then be used by the vehicles control system to control the vehicle attitude and the attitude of various sensors such as cameras. Unused Unused Unused Unused Pitch offset from next waypoint Roll offset from next waypoint Yaw offset from next waypoint
VEHICLE_CMD_DO_SET_ROI_NONE uint16 197 Cancels any previous ROI command returning the vehicle/sensors to default flight characteristics. This can then be used by the vehicles control system to control the vehicle attitude and the attitude of various sensors such as cameras. Unused Unused Unused Unused Unused Unused Unused
VEHICLE_CMD_DO_CONTROL_VIDEO uint16 200 Control onboard camera system. Camera ID (-1 for all) Transmission: 0: disabled, 1: enabled compressed, 2: enabled raw Transmission mode: 0: video stream, >0: single images every n seconds (decimal seconds) Recording: 0: disabled, 1: enabled compressed, 2: enabled raw Unused Unused Unused
VEHICLE_CMD_DO_SET_ROI uint16 201 Sets the region of interest (ROI) for a sensor set or the vehicle itself. This can then be used by the vehicles control system to control the vehicle attitude and the attitude of various sensors such as cameras. [@enum VEHICLE_ROI] Region of interest mode. MISSION index/ target ID. ROI index (allows a vehicle to manage multiple ROI's) Unused x the location of the fixed ROI (see MAV_FRAME) y z
VEHICLE_CMD_DO_DIGICAM_CONTROL uint16 203
VEHICLE_CMD_DO_MOUNT_CONFIGURE uint16 204 Mission command to configure a camera or antenna mount. [@enum MAV_MOUNT_MODE] Mount operation mode Stabilize roll? (1 = yes, 0 = no) Stabilize pitch? (1 = yes, 0 = no) stabilize yaw? (1 = yes, 0 = no) Unused Unused Unused
VEHICLE_CMD_DO_MOUNT_CONTROL uint16 205 Mission command to control a camera or antenna mount. [deg] Pitch or lat, depending on mount mode. [deg] Roll or lon depending on mount mode [deg]/[m] Yaw or alt depending on mount mode Unused Unused Unused [@enum MAV_MOUNT_MODE]
VEHICLE_CMD_DO_SET_CAM_TRIGG_DIST uint16 206 Mission command to set TRIG_DIST for this flight. [m] Camera trigger distance [ms] Shutter integration time Unused Unused Unused Unused Unused
VEHICLE_CMD_DO_FENCE_ENABLE uint16 207 Mission command to enable the geofence. enable? (0=disable, 1=enable) Unused Unused Unused Unused Unused Unused
VEHICLE_CMD_DO_PARACHUTE uint16 208 Mission command to trigger a parachute. action [@enum PARACHUTE_ACTION] (0=disable, 1=enable, 2=release, for some systems see [@enum PARACHUTE_ACTION], not in general message set.) Unused Unused Unused Unused Unused Unused
VEHICLE_CMD_DO_MOTOR_TEST uint16 209 Motor test command. Instance (@range 1, ) throttle type throttle timeout [s] Motor count Test order Unused
VEHICLE_CMD_DO_INVERTED_FLIGHT uint16 210 Change to/from inverted flight. inverted (0=normal, 1=inverted) Unused Unused Unused Unused Unused Unused
VEHICLE_CMD_DO_GRIPPER uint16 211 Command to operate a gripper.
VEHICLE_CMD_DO_AUTOTUNE_ENABLE uint16 212 Enable autotune module. 1 to enable Unused Unused Unused Unused Unused Unused
VEHICLE_CMD_DO_SET_CAM_TRIGG_INTERVAL uint16 214 Mission command to set TRIG_INTERVAL for this flight. [m] Camera trigger distance Shutter integration time (ms) Unused Unused Unused Unused Unused
VEHICLE_CMD_DO_MOUNT_CONTROL_QUAT uint16 220 Mission command to control a camera or antenna mount, using a quaternion as reference. q1 - quaternion param #1, w (1 in null-rotation) q2 - quaternion param #2, x (0 in null-rotation) q3 - quaternion param #3, y (0 in null-rotation) q4 - quaternion param #4, z (0 in null-rotation) Unused Unused Unused
VEHICLE_CMD_DO_GUIDED_MASTER uint16 221 Set id of master controller. System ID Component ID Unused Unused Unused Unused Unused
VEHICLE_CMD_DO_GUIDED_LIMITS uint16 222 Set limits for external control. [s] Timeout - maximum time that external controller will be allowed to control vehicle. 0 means no timeout [m] Absolute altitude min(AMSL) - if vehicle moves below this alt, the command will be aborted and the mission will continue. 0 means no lower altitude limit [m] Absolute altitude max - if vehicle moves above this alt, the command will be aborted and the mission will continue. 0 means no upper altitude limit [m] Horizontal move limit (AMSL) - if vehicle moves more than this distance from it's location at the moment the command was executed, the command will be aborted and the mission will continue. 0 means no horizontal altitude limit Unused Unused Unused
VEHICLE_CMD_DO_SET_MISSION_CURRENT uint16 224 Set the mission item with sequence number seq as current item and emit MISSION_CURRENT (whether or not the mission mode is active). ACKs FAILED if seq is out of range or there is no current mission item. Mission sequence value to set, -1 for the current mission item (use to reset jump counters without changing the current item) Reset repeat/jump counters and clear mission complete flag (1=true,0=false; default:0) Unused Unused Unused Unused Unused
VEHICLE_CMD_DO_LAST uint16 240 NOP - This command is only used to mark the upper limit of the DO commands in the enumeration. Unused Unused Unused Unused Unused Unused Unused
VEHICLE_CMD_PREFLIGHT_CALIBRATION uint16 241 Trigger calibration. This command will be only accepted if in pre-flight mode. See MAVLink spec MAV_CMD_PREFLIGHT_CALIBRATION.
PREFLIGHT_CALIBRATION_TEMPERATURE_CALIBRATION uint16 3 Param value for VEHICLE_CMD_PREFLIGHT_CALIBRATION to start temperature calibration.
VEHICLE_CMD_PREFLIGHT_SET_SENSOR_OFFSETS uint16 242 Set sensor offsets. This command will be only accepted if in pre-flight mode. Sensor to adjust the offsets for: 0: gyros, 1: accelerometer, 2: magnetometer, 3: barometer, 4: optical flow X axis offset (or generic dimension 1), in the sensor's raw units Y axis offset (or generic dimension 2), in the sensor's raw units Z axis offset (or generic dimension 3), in the sensor's raw units Generic dimension 4, in the sensor's raw units Generic dimension 5, in the sensor's raw units Generic dimension 6, in the sensor's raw units
VEHICLE_CMD_PREFLIGHT_UAVCAN uint16 243 UAVCAN configuration. If param 1 == 1 actuator mapping and direction assignment should be started.
VEHICLE_CMD_PREFLIGHT_STORAGE uint16 245 Request storage of different parameter values and logs. This command will be only accepted if in pre-flight mode. Parameter storage: 0: READ FROM FLASH/EEPROM, 1: WRITE CURRENT TO FLASH/EEPROM Mission storage: 0: READ FROM FLASH/EEPROM, 1: WRITE CURRENT TO FLASH/EEPROM Unused Unused Unused Unused Unused
VEHICLE_CMD_PREFLIGHT_REBOOT_SHUTDOWN uint16 246 Request the reboot or shutdown of system components. 0: Do nothing for autopilot, 1: Reboot autopilot, 2: Shutdown autopilot. 0: Do nothing for onboard computer, 1: Reboot onboard computer, 2: Shutdown onboard computer. Unused Unused Unused Unused Unused
VEHICLE_CMD_OBLIQUE_SURVEY uint16 260 Mission command to set a Camera Auto Mount Pivoting Oblique Survey for this flight. [m] Camera trigger distance [ms] Shutter integration time Camera minimum trigger interval Number of positions Roll Pitch Unused
VEHICLE_CMD_DO_SET_STANDARD_MODE uint16 262 Enable the specified standard MAVLink mode. MAV_STANDARD_MODE
VEHICLE_CMD_GIMBAL_DEVICE_INFORMATION uint16 283 Command to ask information about a low level gimbal.
VEHICLE_CMD_MISSION_START uint16 300 Start running a mission. first_item: the first mission item to run last_item: the last mission item to run (after this item is run, the mission ends)
VEHICLE_CMD_ACTUATOR_GROUP_TEST uint16 309 Test groups of related actuators (e.g. all actuators contributing to roll torque). [@enum ACTUATOR_TEST_GROUP] Group [@range -1,1] Value Unused Unused Unused Unused Unused
VEHICLE_CMD_ACTUATOR_TEST uint16 310 Actuator testing command. [@range -1,1] value [s] timeout Unused Unused output function
VEHICLE_CMD_CONFIGURE_ACTUATOR uint16 311 Actuator configuration command. configuration Unused Unused Unused output function
VEHICLE_CMD_ESC_REQUEST_EEPROM uint16 312 Request EEPROM data from an ESC. ESC Index Firmware Type Unused Unused Unused
VEHICLE_CMD_COMPONENT_ARM_DISARM uint16 400 Arms / Disarms a component. 1 to arm, 0 to disarm.
VEHICLE_CMD_RUN_PREARM_CHECKS uint16 401 Instructs a target system to run pre-arm checks.
VEHICLE_CMD_INJECT_FAILURE uint16 420 Inject artificial failure for testing purposes.
VEHICLE_CMD_START_RX_PAIR uint16 500 Starts receiver pairing. 0:Spektrum 0:Spektrum DSM2, 1:Spektrum DSMX
VEHICLE_CMD_REQUEST_MESSAGE uint16 512 Request to send a single instance of the specified message.
VEHICLE_CMD_REQUEST_CAMERA_INFORMATION uint16 521 Request camera information (CAMERA_INFORMATION). 0: No action 1: Request camera capabilities Reserved (all remaining params) Reserved (default:0) Reserved (default:0) Reserved (default:0) Reserved (default:0) Reserved (default:0)
VEHICLE_CMD_SET_CAMERA_MODE uint16 530 Set camera capture mode (photo, video, etc.).
VEHICLE_CMD_SET_CAMERA_ZOOM uint16 531 Set camera zoom.
VEHICLE_CMD_SET_CAMERA_FOCUS uint16 532
VEHICLE_CMD_EXTERNAL_ATTITUDE_ESTIMATE uint16 620 Set an external estimate of vehicle attitude in degrees.
VEHICLE_CMD_DO_GIMBAL_MANAGER_PITCHYAW uint16 1000 Setpoint to be sent to a gimbal manager to set a gimbal pitch and yaw.
VEHICLE_CMD_DO_GIMBAL_MANAGER_CONFIGURE uint16 1001 Gimbal configuration to set which sysid/compid is in primary and secondary control.
VEHICLE_CMD_IMAGE_START_CAPTURE uint16 2000 Start image capture sequence.
VEHICLE_CMD_DO_TRIGGER_CONTROL uint16 2003 Enable or disable on-board camera triggering system.
VEHICLE_CMD_VIDEO_START_CAPTURE uint16 2500 Start a video capture.
VEHICLE_CMD_VIDEO_STOP_CAPTURE uint16 2501 Stop the current video capture.
VEHICLE_CMD_LOGGING_START uint16 2510 Start streaming ULog data.
VEHICLE_CMD_LOGGING_STOP uint16 2511 Stop streaming ULog data.
VEHICLE_CMD_CONTROL_HIGH_LATENCY uint16 2600 Control starting/stopping transmitting data over the high latency link.
VEHICLE_CMD_DO_VTOL_TRANSITION uint16 3000 Command VTOL transition.
VEHICLE_CMD_DO_SET_SAFETY_SWITCH_STATE uint16 5300 Command safety on/off. SAFETY_SAFE (0) to activate safety, SAFETY_DANGEROUS (1) to deactivate safety and allow non-throttling actuator movement Unused Unused Unused Unused Unused Unused
VEHICLE_CMD_ARM_AUTHORIZATION_REQUEST uint16 3001 Request arm authorization.
VEHICLE_CMD_PAYLOAD_PREPARE_DEPLOY uint16 30001 Prepare a payload deployment in the flight plan.
VEHICLE_CMD_PAYLOAD_CONTROL_DEPLOY uint16 30002 Control a pre-programmed payload deployment.
VEHICLE_CMD_FIXED_MAG_CAL_YAW uint16 42006 Magnetometer calibration based on provided known yaw. This allows for fast calibration using WMM field tables in the vehicle, given only the known yaw of the vehicle. If Latitude and longitude are both zero then use the current vehicle location.
VEHICLE_CMD_DO_WINCH uint16 42600 Command to operate winch.
VEHICLE_CMD_EXTERNAL_POSITION_ESTIMATE uint16 43003 External reset of estimator global position when dead reckoning.
VEHICLE_CMD_EXTERNAL_WIND_ESTIMATE uint16 43004
VEHICLE_CMD_ESTIMATOR_SENSOR_ENABLE uint16 43006 Enable/disable estimator sensor fusion. Source (FUSIONSOURCE*) Sensor instance (0-based) Enable (1) or Disable (0) Estimator Instance (NaN: not used) Empty Empty Empty
FUSION_SOURCE_GPS uint8 0 GNSS (EKF2_GPS{i}_CTRL, use instance param)
FUSION_SOURCE_OF uint8 1 Optical Flow (EKF2_OF_CTRL)
FUSION_SOURCE_EV uint8 2 External Vision (EKF2_EV_CTRL)
FUSION_SOURCE_AGP uint8 3 Auxiliary Global Position (EKF2_AGP{i}_CTRL, use instance param)
FUSION_SOURCE_BARO uint8 4 Barometer (EKF2_BARO_CTRL)
FUSION_SOURCE_RNG uint8 5 Range Finder (EKF2_RNG_CTRL)
FUSION_SOURCE_MAG uint8 6 Magnetometer (EKF2_MAG_TYPE)
FUSION_SOURCE_ASPD uint8 7 Airspeed (EKF2_ARSP_THR)
FUSION_SOURCE_RNGBCN uint8 8 Ranging Beacon
VEHICLE_CMD_PX4_INTERNAL_START uint32 65537 Start of PX4 internal only vehicle commands (> UINT16_MAX).
VEHICLE_CMD_SET_GPS_GLOBAL_ORIGIN uint32 100000 Sets the GPS coordinates of the vehicle local origin (0,0,0) position. Unused Unused Unused Unused Latitude (WGS-84) Longitude (WGS-84) [m] Altitude (AMSL from GNSS, positive above ground)
VEHICLE_CMD_SET_NAV_STATE uint32 100001 Change mode by specifying nav_state directly. nav_state Unused Unused Unused Unused Unused Unused
VEHICLE_CMD_DO_SET_GLOBAL_ORIGIN uint16 611 Sets GNSS coordinates of the vehicle local origin (0,0,0) position. Send as COMMAND_INT with MAV_FRAME_GLOBAL_INT. Unused Unused Unused Unused Latitude (WGS-84) Longitude (WGS-84) [m] Altitude (AMSL)
VEHICLE_CMD_GUIDED_CHANGE_HEADING uint16 43002 Change heading/course. param1: heading type (0=course-over-ground, 1=heading). param2: target [deg]. param3: max rate [deg/s]. Heading type (HEADING_TYPE enum) [deg] Target bearing [0..360] [deg/s] Max rate of change Unused Unused Unused Unused
VEHICLE_MOUNT_MODE_RETRACT uint8 0 Load and keep safe position (Roll,Pitch,Yaw) from permanent memory and stop stabilization.
VEHICLE_MOUNT_MODE_NEUTRAL uint8 1 Load and keep neutral position (Roll,Pitch,Yaw) from permanent memory.
VEHICLE_MOUNT_MODE_MAVLINK_TARGETING uint8 2 Load neutral position and start MAVLink Roll,Pitch,Yaw control with stabilization.
VEHICLE_MOUNT_MODE_RC_TARGETING uint8 3 Load neutral position and start RC Roll,Pitch,Yaw control with stabilization.
VEHICLE_MOUNT_MODE_GPS_POINT uint8 4 Load neutral position and start to point to Lat,Lon,Alt.
VEHICLE_MOUNT_MODE_ENUM_END uint8 5
VEHICLE_ROI_NONE uint8 0 No region of interest.
VEHICLE_ROI_WPNEXT uint8 1 Point toward next MISSION.
VEHICLE_ROI_WPINDEX uint8 2 Point toward given MISSION.
VEHICLE_ROI_LOCATION uint8 3 Point toward fixed location.
VEHICLE_ROI_TARGET uint8 4 Point toward target.
VEHICLE_ROI_ENUM_END uint8 5
ACTUATOR_CONFIGURATION_NONE uint8 0 Do nothing.
ACTUATOR_CONFIGURATION_BEEP uint8 1 Command the actuator to beep now.
ACTUATOR_CONFIGURATION_3D_MODE_ON uint8 2 Permanently set the actuator (ESC) to 3D mode (reversible thrust).
ACTUATOR_CONFIGURATION_3D_MODE_OFF uint8 3 Permanently set the actuator (ESC) to non 3D mode (non-reversible thrust).
ACTUATOR_CONFIGURATION_SPIN_DIRECTION1 uint8 4 Permanently set the actuator (ESC) to spin direction 1 (which can be clockwise or counter-clockwise).
ACTUATOR_CONFIGURATION_SPIN_DIRECTION2 uint8 5 Permanently set the actuator (ESC) to spin direction 2 (opposite of direction 1).
PARACHUTE_ACTION_DISABLE uint8 0
PARACHUTE_ACTION_ENABLE uint8 1
PARACHUTE_ACTION_RELEASE uint8 2
FAILURE_UNIT_SENSOR_GYRO uint8 0
FAILURE_UNIT_SENSOR_ACCEL uint8 1
FAILURE_UNIT_SENSOR_MAG uint8 2
FAILURE_UNIT_SENSOR_BARO uint8 3
FAILURE_UNIT_SENSOR_GPS uint8 4
FAILURE_UNIT_SENSOR_OPTICAL_FLOW uint8 5
FAILURE_UNIT_SENSOR_VIO uint8 6
FAILURE_UNIT_SENSOR_DISTANCE_SENSOR uint8 7
FAILURE_UNIT_SENSOR_AIRSPEED uint8 8
FAILURE_UNIT_SYSTEM_BATTERY uint8 100
FAILURE_UNIT_SYSTEM_MOTOR uint8 101
FAILURE_UNIT_SYSTEM_SERVO uint8 102
FAILURE_UNIT_SYSTEM_AVOIDANCE uint8 103
FAILURE_UNIT_SYSTEM_RC_SIGNAL uint8 104
FAILURE_UNIT_SYSTEM_MAVLINK_SIGNAL uint8 105
FAILURE_UNIT_SYSTEM_ESC uint8 106
FAILURE_UNIT_SYSTEM_TRAFFIC_AVOIDANCE uint8 107
FAILURE_UNIT_DATALINK_LTE uint8 150
FAILURE_UNIT_DATALINK_WIFI uint8 151
FAILURE_UNIT_DATALINK_TELEM_RADIO uint8 152
FAILURE_UNIT_BUS_CAN uint8 200
FAILURE_UNIT_BUS_I2C uint8 201
FAILURE_TYPE_OK uint8 0
FAILURE_TYPE_OFF uint8 1
FAILURE_TYPE_STUCK uint8 2
FAILURE_TYPE_GARBAGE uint8 3
FAILURE_TYPE_WRONG uint8 4
FAILURE_TYPE_SLOW uint8 5
FAILURE_TYPE_DELAYED uint8 6
FAILURE_TYPE_INTERMITTENT uint8 7
FAILURE_TYPE_DRIFT uint8 8
SPEED_TYPE_AIRSPEED uint8 0
SPEED_TYPE_GROUNDSPEED uint8 1
SPEED_TYPE_CLIMB_SPEED uint8 2
SPEED_TYPE_DESCEND_SPEED uint8 3
ORBIT_YAW_BEHAVIOUR_HOLD_FRONT_TO_CIRCLE_CENTER uint8 0
ORBIT_YAW_BEHAVIOUR_HOLD_INITIAL_HEADING uint8 1
ORBIT_YAW_BEHAVIOUR_UNCONTROLLED uint8 2
ORBIT_YAW_BEHAVIOUR_HOLD_FRONT_TANGENT_TO_CIRCLE uint8 3
ORBIT_YAW_BEHAVIOUR_RC_CONTROLLED uint8 4
ORBIT_YAW_BEHAVIOUR_UNCHANGED uint8 5
RC_TYPE_SPEKTRUM uint8 0
RC_TYPE_CRSF uint8 1
RC_SUB_TYPE_SPEKTRUM_DSM2 uint8 0
RC_SUB_TYPE_SPEKTRUM_DSMX uint8 1
RC_SUB_TYPE_SPEKTRUM_DSMX8 uint8 2
ARMING_ACTION_DISARM int8 0
ARMING_ACTION_ARM int8 1
GRIPPER_ACTION_RELEASE uint8 0
GRIPPER_ACTION_GRAB uint8 1
SAFETY_SAFE uint8 0 Activate safety (MAVLink SAFETY_SWITCH_STATE_SAFE)
SAFETY_DANGEROUS uint8 1 Deactivate safety (MAVLink SAFETY_SWITCH_STATE_DANGEROUS)
ACTUATOR_TEST_GROUP_ROLL_TORQUE uint8 0
ACTUATOR_TEST_GROUP_PITCH_TORQUE uint8 1
ACTUATOR_TEST_GROUP_YAW_TORQUE uint8 2
ACTUATOR_TEST_GROUP_COLLECTIVE_TILT uint8 3
ACTUATOR_TEST_GROUP_X_THRUST uint8 4
ACTUATOR_TEST_GROUP_Y_THRUST uint8 5
ACTUATOR_TEST_GROUP_Z_THRUST uint8 6
ORB_QUEUE_LENGTH uint8 8
COMPONENT_MODE_EXECUTOR_START uint16 1000

Source Message

Source file (GitHub)

::: details Click here to see original file

# Vehicle Command uORB message. Used for commanding a mission / action / etc.
# Follows the MAVLink COMMAND_INT / COMMAND_LONG definition

uint32 MESSAGE_VERSION = 0

uint64 timestamp # [us] Time since system start.

uint16 VEHICLE_CMD_CUSTOM_0 = 0 # Test command.
uint16 VEHICLE_CMD_CUSTOM_1 = 1 # Test command.
uint16 VEHICLE_CMD_CUSTOM_2 = 2 # Test command.
uint16 VEHICLE_CMD_NAV_WAYPOINT = 16 # Navigate to MISSION. |[s] (decimal) Hold time. (ignored by fixed wing, time to stay at MISSION for rotary wing)|[m] Acceptance radius (if the sphere with this radius is hit, the MISSION counts as reached)|0 to pass through the WP, if > 0 radius [m] to pass by WP. Positive value for clockwise orbit, negative value for counter-clockwise orbit. Allows trajectory control.|Desired yaw angle at MISSION (rotary wing)|Latitude|Longitude|Altitude|
uint16 VEHICLE_CMD_NAV_LOITER_UNLIM = 17 # Loiter around this MISSION an unlimited amount of time. |Unused|Unused|[m] Radius around MISSION. If positive loiter clockwise, else counter-clockwise|Desired yaw angle.|Latitude|Longitude|Altitude|
uint16 VEHICLE_CMD_NAV_LOITER_TURNS = 18 # Loiter around this MISSION for X turns. |Turns|Unused|Radius around MISSION [m]. If positive loiter clockwise, else counter-clockwise|Desired yaw angle.|Latitude|Longitude|Altitude|
uint16 VEHICLE_CMD_NAV_LOITER_TIME = 19 # Loiter around this MISSION for time. |[s] Seconds (decimal)|Unused|Radius around MISSION [m]. If positive loiter clockwise, else counter-clockwise|Desired yaw angle.|Latitude|Longitude|Altitude|
uint16 VEHICLE_CMD_NAV_RETURN_TO_LAUNCH = 20 # Return to launch location. |Unused|Unused|Unused|Unused|Unused|Unused|Unused|
uint16 VEHICLE_CMD_NAV_LAND = 21 # Land at location. |Unused|Unused|Unused|Desired yaw angle.|Latitude|Longitude|Altitude|
uint16 VEHICLE_CMD_NAV_TAKEOFF = 22 # Takeoff from ground / hand. |Unused (FW pitch from FW_TKO_PITCH_MIN)|Unused|Unused|[deg] [@range 0,360] Yaw angle in NED if yaw source available, ignored otherwise|Latitude (WGS-84)|Longitude (WGS-84)|[m] Altitude AMSL|
uint16 VEHICLE_CMD_NAV_PRECLAND = 23 # Attempt a precision landing.
uint16 VEHICLE_CMD_DO_ORBIT = 34 # Start orbiting on the circumference of a circle defined by the parameters. |[m] Radius|[m/s] Velocity|[@enum ORBIT_YAW_BEHAVIOUR] Yaw behaviour|Unused|Latitude/X|Longitude/Y|Altitude/Z|
uint16 VEHICLE_CMD_DO_FIGUREEIGHT = 35 # Start flying on the outline of a figure eight defined by the parameters. |[m] Major radius|[m] Minor radius|[m/s] Velocity|Orientation|Latitude/X|Longitude/Y|Altitude/Z|
uint16 VEHICLE_CMD_NAV_ROI = 80 # Sets the region of interest (ROI) for a sensor set or the vehicle itself. This can then be used by the vehicles control system to control the vehicle attitude and the attitude of various sensors such as cameras. |[@enum VEHICLE_ROI] Region of interest mode.|MISSION index/ target ID.|ROI index (allows a vehicle to manage multiple ROI's)|Unused|x the location of the fixed ROI (see MAV_FRAME)|y|z|
uint16 VEHICLE_CMD_NAV_PATHPLANNING = 81 # Control autonomous path planning on the MAV. |0: Disable local obstacle avoidance / local path planning (without resetting map), 1: Enable local path planning, 2: Enable and reset local path planning|0: Disable full path planning (without resetting map), 1: Enable, 2: Enable and reset map/occupancy grid, 3: Enable and reset planned route, but not occupancy grid|Unused|[deg] [@range 0, 360] Yaw angle at goal, in compass degrees|Latitude/X of goal|Longitude/Y of goal|Altitude/Z of goal|
uint16 VEHICLE_CMD_NAV_VTOL_TAKEOFF = 84 # Takeoff from ground / hand and transition to fixed wing. |Minimum pitch (if airspeed sensor present), desired pitch without sensor|Transition heading, 0: Default, 3: Use specified transition heading|Unused|Yaw angle (if magnetometer present), ignored without magnetometer|Latitude|Longitude|Altitude|
uint16 VEHICLE_CMD_NAV_VTOL_LAND = 85 # Transition to MC and land at location. |Unused|Unused|Unused|Desired yaw angle.|Latitude|Longitude|Altitude|
uint16 VEHICLE_CMD_NAV_GUIDED_LIMITS = 90 # Set limits for external control. |[s] Timeout  - maximum time that external controller will be allowed to control vehicle. 0 means no timeout|[m] Absolute altitude min AMSL - if vehicle moves below this alt, the command will be aborted and the mission will continue. 0 means no lower altitude limit|[m] Absolute altitude max - if vehicle moves above this alt, the command will be aborted and the mission will continue. 0 means no upper altitude limit|[m] Horizontal move limit (AMSL) - if vehicle moves more than this distance from it's location at the moment the command was executed, the command will be aborted and the mission will continue. 0 means no horizontal altitude limit|Unused|Unused|Unused|
uint16 VEHICLE_CMD_NAV_GUIDED_MASTER = 91 # Set id of master controller. |System ID|Component ID|Unused|Unused|Unused|Unused|Unused|
uint16 VEHICLE_CMD_NAV_DELAY = 93 # Delay the next navigation command a number of seconds or until a specified time. |[s] Delay (decimal, -1 to enable time-of-day fields)|[h] hour (24h format, UTC, -1 to ignore)|minute (24h format, UTC, -1 to ignore)|second (24h format, UTC)|Unused|Unused|Unused|
uint16 VEHICLE_CMD_NAV_LAST = 95 # NOP - This command is only used to mark the upper limit of the NAV/ACTION commands in the enumeration.|Unused|Unused|Unused|Unused|Unused|Unused|Unused|
uint16 VEHICLE_CMD_CONDITION_DELAY = 112 # Delay mission state machine. |[s] Delay (decimal seconds)|Unused|Unused|Unused|Unused|Unused|Unused|
uint16 VEHICLE_CMD_CONDITION_CHANGE_ALT = 113 # Ascend/descend at rate. Delay mission state machine until desired altitude reached.|Descent / Ascend rate (m/s)|Unused|Unused|Unused|Unused|Unused|Finish Altitude|
uint16 VEHICLE_CMD_CONDITION_DISTANCE = 114 # Delay mission state machine until within desired distance of next NAV point. |Distance [m]|Unused|Unused|Unused|Unused|Unused|Unused|
uint16 VEHICLE_CMD_CONDITION_YAW = 115 # Reach a certain target angle. |[deg] [@range 0,360] Target angle. 0 is north|[deg/s] Speed during yaw change|[@range -1,1] Direction: negative: counter clockwise, positive: clockwise |[ 1,0] Relative offset or absolute angle|Unused|Unused|Unused|
uint16 VEHICLE_CMD_CONDITION_LAST = 159 # NOP - This command is only used to mark the upper limit of the CONDITION commands in the enumeration. |Unused|Unused|Unused|Unused|Unused|Unused|Unused|
uint16 VEHICLE_CMD_CONDITION_GATE = 4501 # Wait until passing a threshold. |2D coord mode: 0: Orthogonal to planned route|Altitude mode: 0: Ignore altitude|Unused|Unused|Lat|Lon|Alt|
uint16 VEHICLE_CMD_DO_SET_MODE = 176 # Set system mode. |Mode, as defined by ENUM MAV_MODE|Unused|Unused|Unused|Unused|Unused|Unused|
uint16 VEHICLE_CMD_DO_JUMP = 177 # Jump to the desired command in the mission list. Repeat this action only the specified number of times. |Sequence number|Repeat count|Unused|Unused|Unused|Unused|Unused|
uint16 VEHICLE_CMD_DO_CHANGE_SPEED = 178 # Change speed and/or throttle set points. |[@enum SPEED_TYPE] Speed type (0=Airspeed, 1=Ground Speed)|Speed (m/s, -1 indicates no change)|[%] Throttle ( Percent, -1 indicates no change)|Unused|Unused|Unused|Unused|
uint16 VEHICLE_CMD_DO_SET_HOME = 179 # Changes the home location either to the current location or a specified location. |Use current (1=use current location, 0=use specified location)|Unused|Unused|Unused|Latitude|Longitude|Altitude|
uint16 VEHICLE_CMD_DO_SET_PARAMETER = 180 # Set a system parameter. Caution! Use of this command requires knowledge of the numeric enumeration value of the parameter. |Parameter number|Parameter value|Unused|Unused|Unused|Unused|Unused|
uint16 VEHICLE_CMD_DO_SET_RELAY = 181 # Set a relay to a condition. |Relay number|Setting (1=on, 0=off, others possible depending on system hardware)|Unused|Unused|Unused|Unused|Unused|
uint16 VEHICLE_CMD_DO_REPEAT_RELAY = 182 # Cycle a relay on and off for a desired number of cycles with a desired period. |Relay number|Cycle count|[s] Cycle time (decimal seconds)|Unused|Unused|Unused|Unused|
uint16 VEHICLE_CMD_DO_REPEAT_SERVO = 184 # Cycle a between its nominal setting and a desired PWM for a desired number of cycles with a desired period. |Servo number|[us] PWM rate (1000 to 2000 typical)|Cycle count|[s] Cycle time|Unused|Unused|Unused|
uint16 VEHICLE_CMD_DO_FLIGHTTERMINATION = 185 # Terminate flight immediately. |Flight termination activated if > 0.5|Unused|Unused|Unused|Unused|Unused|Unused|
uint16 VEHICLE_CMD_DO_CHANGE_ALTITUDE = 186 # Set the vehicle to Loiter mode and change the altitude to specified value. |Altitude|Frame of new altitude|Unused|Unused|Unused|Unused|Unused|
uint16 VEHICLE_CMD_DO_SET_ACTUATOR = 187 # Sets actuators (e.g. servos) to a desired value. |Actuator 1|Actuator 2|Actuator 3|Actuator 4|Actuator 5|Actuator 6|Index|
uint16 VEHICLE_CMD_DO_LAND_START = 189 # Mission command to perform a landing. This is used as a marker in a mission to tell the autopilot where a sequence of mission items that represents a landing starts. It may also be sent via a COMMAND_LONG to trigger a landing, in which case the nearest (geographically) landing sequence in the mission will be used. The Latitude/Longitude is optional, and may be set to 0/0 if not needed. If specified then it will be used to help find the closest landing sequence. |Unused|Unused|Unused|Unused|Latitude|Longitude|Unused|
uint16 VEHICLE_CMD_DO_GO_AROUND = 191 # Mission command to safely abort an autonomous landing. |[m] Altitude|Unused|Unused|Unused|Unused|Unused|Unused|
uint16 VEHICLE_CMD_DO_REPOSITION = 192 # Reposition to specific WGS84 GPS position. |[m/s] Ground speed|Bitmask|[m] Loiter radius for planes|[deg] Yaw|Latitude|Longitude|Altitude|
uint16 VEHICLE_CMD_DO_PAUSE_CONTINUE = 193
uint16 VEHICLE_CMD_DO_SET_ROI_LOCATION = 195 # Sets the region of interest (ROI) to a location. This can then be used by the vehicles control system to control the vehicle attitude and the attitude of various sensors such as cameras. |Unused|Unused|Unused|Unused|Latitude|Longitude|Altitude|
uint16 VEHICLE_CMD_DO_SET_ROI_WPNEXT_OFFSET = 196 # Sets the region of interest (ROI) to be toward next waypoint, with optional pitch/roll/yaw offset. This can then be used by the vehicles control system to control the vehicle attitude and the attitude of various sensors such as cameras. |Unused|Unused|Unused|Unused|Pitch offset from next waypoint|Roll offset from next waypoint|Yaw offset from next waypoint|
uint16 VEHICLE_CMD_DO_SET_ROI_NONE = 197 # Cancels any previous ROI command returning the vehicle/sensors to default flight characteristics. This can then be used by the vehicles control system to control the vehicle attitude and the attitude of various sensors such as cameras. |Unused|Unused|Unused|Unused|Unused|Unused|Unused|
uint16 VEHICLE_CMD_DO_CONTROL_VIDEO = 200 # Control onboard camera system. |Camera ID (-1 for all)|Transmission: 0: disabled, 1: enabled compressed, 2: enabled raw|Transmission mode: 0: video stream, >0: single images every n seconds (decimal seconds)|Recording: 0: disabled, 1: enabled compressed, 2: enabled raw|Unused|Unused|Unused|
uint16 VEHICLE_CMD_DO_SET_ROI = 201 # Sets the region of interest (ROI) for a sensor set or the vehicle itself. This can then be used by the vehicles control system to control the vehicle attitude and the attitude of various sensors such as cameras. |[@enum VEHICLE_ROI] Region of interest mode.|MISSION index/ target ID.|ROI index (allows a vehicle to manage multiple ROI's)|Unused|x the location of the fixed ROI (see MAV_FRAME)|y|z|
uint16 VEHICLE_CMD_DO_DIGICAM_CONTROL=203
uint16 VEHICLE_CMD_DO_MOUNT_CONFIGURE=204 # Mission command to configure a camera or antenna mount. |[@enum MAV_MOUNT_MODE] Mount operation mode|Stabilize roll? (1 = yes, 0 = no)|Stabilize pitch? (1 = yes, 0 = no)|stabilize yaw? (1 = yes, 0 = no)|Unused|Unused|Unused|
uint16 VEHICLE_CMD_DO_MOUNT_CONTROL=205 # Mission command to control a camera or antenna mount. |[deg] Pitch or lat, depending on mount mode.|[deg] Roll or lon depending on mount mode|[deg]/[m] Yaw or alt depending on mount mode|Unused|Unused|Unused|[@enum MAV_MOUNT_MODE]|
uint16 VEHICLE_CMD_DO_SET_CAM_TRIGG_DIST=206 # Mission command to set TRIG_DIST for this flight. |[m] Camera trigger distance|[ms] Shutter integration time|Unused|Unused|Unused|Unused|Unused|
uint16 VEHICLE_CMD_DO_FENCE_ENABLE=207 # Mission command to enable the geofence. |enable? (0=disable, 1=enable)|Unused|Unused|Unused|Unused|Unused|Unused|
uint16 VEHICLE_CMD_DO_PARACHUTE=208 # Mission command to trigger a parachute. |action [@enum PARACHUTE_ACTION] (0=disable, 1=enable, 2=release, for some systems see [@enum PARACHUTE_ACTION], not in general message set.)|Unused|Unused|Unused|Unused|Unused|Unused|
uint16 VEHICLE_CMD_DO_MOTOR_TEST=209 # Motor test command. |Instance (@range 1, )|throttle type|throttle|timeout [s]|Motor count|Test order|Unused|
uint16 VEHICLE_CMD_DO_INVERTED_FLIGHT=210 # Change to/from inverted flight. |inverted (0=normal, 1=inverted)|Unused|Unused|Unused|Unused|Unused|Unused|
uint16 VEHICLE_CMD_DO_GRIPPER = 211 # Command to operate a gripper.
uint16 VEHICLE_CMD_DO_AUTOTUNE_ENABLE = 212 # Enable autotune module. |1 to enable|Unused|Unused|Unused|Unused|Unused|Unused|
uint16 VEHICLE_CMD_DO_SET_CAM_TRIGG_INTERVAL=214 # Mission command to set TRIG_INTERVAL for this flight. |[m] Camera trigger distance|Shutter integration time (ms)|Unused|Unused|Unused|Unused|Unused|
uint16 VEHICLE_CMD_DO_MOUNT_CONTROL_QUAT=220 # Mission command to control a camera or antenna mount, using a quaternion as reference. |q1 - quaternion param #1, w (1 in null-rotation)|q2 - quaternion param #2, x (0 in null-rotation)|q3 - quaternion param #3, y (0 in null-rotation)|q4 - quaternion param #4, z (0 in null-rotation)|Unused|Unused|Unused|
uint16 VEHICLE_CMD_DO_GUIDED_MASTER=221 # Set id of master controller. |System ID|Component ID|Unused|Unused|Unused|Unused|Unused|
uint16 VEHICLE_CMD_DO_GUIDED_LIMITS=222 # Set limits for external control. |[s] Timeout - maximum time that external controller will be allowed to control vehicle. 0 means no timeout|[m] Absolute altitude min(AMSL) - if vehicle moves below this alt, the command will be aborted and the mission will continue. 0 means no lower altitude limit|[m] Absolute altitude max - if vehicle moves above this alt, the command will be aborted and the mission will continue. 0 means no upper altitude limit|[m] Horizontal move limit (AMSL) - if vehicle moves more than this distance from it's location at the moment the command was executed, the command will be aborted and the mission will continue. 0 means no horizontal altitude limit|Unused|Unused|Unused|
uint16 VEHICLE_CMD_DO_SET_MISSION_CURRENT = 224 # Set the mission item with sequence number seq as current item and emit MISSION_CURRENT (whether or not the mission mode is active). ACKs FAILED if seq is out of range or there is no current mission item. |Mission sequence value to set, -1 for the current mission item (use to reset jump counters without changing the current item)|Reset repeat/jump counters and clear mission complete flag (1=true,0=false; default:0)|Unused|Unused|Unused|Unused|Unused|
uint16 VEHICLE_CMD_DO_LAST = 240 # NOP - This command is only used to mark the upper limit of the DO commands in the enumeration. |Unused|Unused|Unused|Unused|Unused|Unused|Unused|
uint16 VEHICLE_CMD_PREFLIGHT_CALIBRATION = 241 # Trigger calibration. This command will be only accepted if in pre-flight mode. See MAVLink spec MAV_CMD_PREFLIGHT_CALIBRATION.
uint16 PREFLIGHT_CALIBRATION_TEMPERATURE_CALIBRATION = 3# Param value for VEHICLE_CMD_PREFLIGHT_CALIBRATION to start temperature calibration.
uint16 VEHICLE_CMD_PREFLIGHT_SET_SENSOR_OFFSETS = 242 # Set sensor offsets. This command will be only accepted if in pre-flight mode. |Sensor to adjust the offsets for: 0: gyros, 1: accelerometer, 2: magnetometer, 3: barometer, 4: optical flow|X axis offset (or generic dimension 1), in the sensor's raw units|Y axis offset (or generic dimension 2), in the sensor's raw units|Z axis offset (or generic dimension 3), in the sensor's raw units|Generic dimension 4, in the sensor's raw units|Generic dimension 5, in the sensor's raw units|Generic dimension 6, in the sensor's raw units|
uint16 VEHICLE_CMD_PREFLIGHT_UAVCAN = 243 # UAVCAN configuration. If param 1 == 1 actuator mapping and direction assignment should be started.
uint16 VEHICLE_CMD_PREFLIGHT_STORAGE = 245 # Request storage of different parameter values and logs. This command will be only accepted if in pre-flight mode. |Parameter storage: 0: READ FROM FLASH/EEPROM, 1: WRITE CURRENT TO FLASH/EEPROM|Mission storage: 0: READ FROM FLASH/EEPROM, 1: WRITE CURRENT TO FLASH/EEPROM|Unused|Unused|Unused|Unused|Unused|
uint16 VEHICLE_CMD_PREFLIGHT_REBOOT_SHUTDOWN = 246 # Request the reboot or shutdown of system components. |0: Do nothing for autopilot, 1: Reboot autopilot, 2: Shutdown autopilot.|0: Do nothing for onboard computer, 1: Reboot onboard computer, 2: Shutdown onboard computer.|Unused|Unused|Unused|Unused|Unused|
uint16 VEHICLE_CMD_OBLIQUE_SURVEY=260 # Mission command to set a Camera Auto Mount Pivoting Oblique Survey for this flight. |[m] Camera trigger distance|[ms] Shutter integration time|Camera minimum trigger interval|Number of positions|Roll|Pitch|Unused|
uint16 VEHICLE_CMD_DO_SET_STANDARD_MODE=262 # Enable the specified standard MAVLink mode. |MAV_STANDARD_MODE|
uint16 VEHICLE_CMD_GIMBAL_DEVICE_INFORMATION = 283 # Command to ask information about a low level gimbal.

uint16 VEHICLE_CMD_MISSION_START = 300 # Start running a mission. |first_item: the first mission item to run|last_item: the last mission item to run (after this item is run, the mission ends)|
uint16 VEHICLE_CMD_ACTUATOR_GROUP_TEST = 309 # Test groups of related actuators (e.g. all actuators contributing to roll torque). |[@enum ACTUATOR_TEST_GROUP] Group|[@range -1,1] Value|Unused|Unused|Unused|Unused|Unused|
uint16 VEHICLE_CMD_ACTUATOR_TEST = 310 # Actuator testing command. |[@range -1,1] value|[s] timeout|Unused|Unused|output function|
uint16 VEHICLE_CMD_CONFIGURE_ACTUATOR = 311 # Actuator configuration command. |configuration|Unused|Unused|Unused|output function|
uint16 VEHICLE_CMD_ESC_REQUEST_EEPROM = 312 # Request EEPROM data from an ESC. |ESC Index|Firmware Type|Unused|Unused|Unused|
uint16 VEHICLE_CMD_COMPONENT_ARM_DISARM = 400 # Arms / Disarms a component. |1 to arm, 0 to disarm.
uint16 VEHICLE_CMD_RUN_PREARM_CHECKS = 401 # Instructs a target system to run pre-arm checks.
uint16 VEHICLE_CMD_INJECT_FAILURE = 420 # Inject artificial failure for testing purposes.
uint16 VEHICLE_CMD_START_RX_PAIR = 500 # Starts receiver pairing. |0:Spektrum|0:Spektrum DSM2, 1:Spektrum DSMX|
uint16 VEHICLE_CMD_REQUEST_MESSAGE = 512 # Request to send a single instance of the specified message.
uint16 VEHICLE_CMD_REQUEST_CAMERA_INFORMATION = 521 # Request camera information (CAMERA_INFORMATION). |0: No action 1: Request camera capabilities|Reserved (all remaining params)|Reserved (default:0)|Reserved (default:0)|Reserved (default:0)|Reserved (default:0)|Reserved (default:0)|
uint16 VEHICLE_CMD_SET_CAMERA_MODE = 530 # Set camera capture mode (photo, video, etc.).
uint16 VEHICLE_CMD_SET_CAMERA_ZOOM = 531 # Set camera zoom.
uint16 VEHICLE_CMD_SET_CAMERA_FOCUS = 532
uint16 VEHICLE_CMD_EXTERNAL_ATTITUDE_ESTIMATE = 620 # Set an external estimate of vehicle attitude in degrees.
uint16 VEHICLE_CMD_DO_GIMBAL_MANAGER_PITCHYAW = 1000 # Setpoint to be sent to a gimbal manager to set a gimbal pitch and yaw.
uint16 VEHICLE_CMD_DO_GIMBAL_MANAGER_CONFIGURE = 1001 # Gimbal configuration to set which sysid/compid is in primary and secondary control.
uint16 VEHICLE_CMD_IMAGE_START_CAPTURE = 2000 # Start image capture sequence.
uint16 VEHICLE_CMD_DO_TRIGGER_CONTROL = 2003 # Enable or disable on-board camera triggering system.
uint16 VEHICLE_CMD_VIDEO_START_CAPTURE = 2500 # Start a video capture.
uint16 VEHICLE_CMD_VIDEO_STOP_CAPTURE = 2501 # Stop the current video capture.
uint16 VEHICLE_CMD_LOGGING_START = 2510 # Start streaming ULog data.
uint16 VEHICLE_CMD_LOGGING_STOP = 2511 # Stop streaming ULog data.
uint16 VEHICLE_CMD_CONTROL_HIGH_LATENCY = 2600 # Control starting/stopping transmitting data over the high latency link.
uint16 VEHICLE_CMD_DO_VTOL_TRANSITION = 3000 # Command VTOL transition.
uint16 VEHICLE_CMD_DO_SET_SAFETY_SWITCH_STATE = 5300 # Command safety on/off. |SAFETY_SAFE (0) to activate safety, SAFETY_DANGEROUS (1) to deactivate safety and allow non-throttling actuator movement|Unused|Unused|Unused|Unused|Unused|Unused|
uint16 VEHICLE_CMD_ARM_AUTHORIZATION_REQUEST = 3001 # Request arm authorization.
uint16 VEHICLE_CMD_PAYLOAD_PREPARE_DEPLOY = 30001 # Prepare a payload deployment in the flight plan.
uint16 VEHICLE_CMD_PAYLOAD_CONTROL_DEPLOY = 30002 # Control a pre-programmed payload deployment.
uint16 VEHICLE_CMD_FIXED_MAG_CAL_YAW = 42006 # Magnetometer calibration based on provided known yaw. This allows for fast calibration using WMM field tables in the vehicle, given only the known yaw of the vehicle. If Latitude and longitude are both zero then use the current vehicle location.
uint16 VEHICLE_CMD_DO_WINCH = 42600 # Command to operate winch.

uint16 VEHICLE_CMD_EXTERNAL_POSITION_ESTIMATE = 43003 # External reset of estimator global position when dead reckoning.
uint16 VEHICLE_CMD_EXTERNAL_WIND_ESTIMATE = 43004
uint16 VEHICLE_CMD_ESTIMATOR_SENSOR_ENABLE = 43006 # Enable/disable estimator sensor fusion. |Source (FUSION_SOURCE_*)|Sensor instance (0-based)|Enable (1) or Disable (0)|Estimator Instance (NaN: not used)|Empty|Empty|Empty|
# Sensor fusion source types for VEHICLE_CMD_ESTIMATOR_SENSOR_ENABLE
uint8 FUSION_SOURCE_GPS = 0   # GNSS (EKF2_GPS{i}_CTRL, use instance param)
uint8 FUSION_SOURCE_OF = 1    # Optical Flow (EKF2_OF_CTRL)
uint8 FUSION_SOURCE_EV = 2    # External Vision (EKF2_EV_CTRL)
uint8 FUSION_SOURCE_AGP = 3   # Auxiliary Global Position (EKF2_AGP{i}_CTRL, use instance param)
uint8 FUSION_SOURCE_BARO = 4  # Barometer (EKF2_BARO_CTRL)
uint8 FUSION_SOURCE_RNG = 5   # Range Finder (EKF2_RNG_CTRL)
uint8 FUSION_SOURCE_MAG = 6   # Magnetometer (EKF2_MAG_TYPE)
uint8 FUSION_SOURCE_ASPD = 7  # Airspeed (EKF2_ARSP_THR)
uint8 FUSION_SOURCE_RNGBCN = 8 # Ranging Beacon

# PX4 vehicle commands (beyond 16 bit MAVLink commands).
uint32 VEHICLE_CMD_PX4_INTERNAL_START = 65537 # Start of PX4 internal only vehicle commands (> UINT16_MAX).
uint32 VEHICLE_CMD_SET_GPS_GLOBAL_ORIGIN = 100000 # Sets the GPS coordinates of the vehicle local origin (0,0,0) position. |Unused|Unused|Unused|Unused|Latitude (WGS-84)|Longitude (WGS-84)|[m] Altitude (AMSL from GNSS, positive above ground)|
uint32 VEHICLE_CMD_SET_NAV_STATE = 100001 # Change mode by specifying nav_state directly. |nav_state|Unused|Unused|Unused|Unused|Unused|Unused|

uint16 VEHICLE_CMD_DO_SET_GLOBAL_ORIGIN = 611 # Sets GNSS coordinates of the vehicle local origin (0,0,0) position. Send as COMMAND_INT with MAV_FRAME_GLOBAL_INT. |Unused|Unused|Unused|Unused|Latitude (WGS-84)|Longitude (WGS-84)|[m] Altitude (AMSL)|
uint16 VEHICLE_CMD_GUIDED_CHANGE_HEADING = 43002 # Change heading/course. param1: heading type (0=course-over-ground, 1=heading). param2: target [deg]. param3: max rate [deg/s]. |Heading type (HEADING_TYPE enum)|[deg] Target bearing [0..360]|[deg/s] Max rate of change|Unused|Unused|Unused|Unused|

uint8 VEHICLE_MOUNT_MODE_RETRACT = 0 # Load and keep safe position (Roll,Pitch,Yaw) from permanent memory and stop stabilization.
uint8 VEHICLE_MOUNT_MODE_NEUTRAL = 1 # Load and keep neutral position (Roll,Pitch,Yaw) from permanent memory.
uint8 VEHICLE_MOUNT_MODE_MAVLINK_TARGETING = 2 # Load neutral position and start MAVLink Roll,Pitch,Yaw control with stabilization.
uint8 VEHICLE_MOUNT_MODE_RC_TARGETING = 3 # Load neutral position and start RC Roll,Pitch,Yaw control with stabilization.
uint8 VEHICLE_MOUNT_MODE_GPS_POINT = 4 # Load neutral position and start to point to Lat,Lon,Alt.
uint8 VEHICLE_MOUNT_MODE_ENUM_END = 5 #

uint8 VEHICLE_ROI_NONE = 0 # No region of interest.
uint8 VEHICLE_ROI_WPNEXT = 1 # Point toward next MISSION.
uint8 VEHICLE_ROI_WPINDEX = 2 # Point toward given MISSION.
uint8 VEHICLE_ROI_LOCATION = 3 # Point toward fixed location.
uint8 VEHICLE_ROI_TARGET = 4 # Point toward target.
uint8 VEHICLE_ROI_ENUM_END = 5

uint8 ACTUATOR_CONFIGURATION_NONE = 0 # Do nothing.
uint8 ACTUATOR_CONFIGURATION_BEEP = 1 # Command the actuator to beep now.
uint8 ACTUATOR_CONFIGURATION_3D_MODE_ON = 2 # Permanently set the actuator (ESC) to 3D mode (reversible thrust).
uint8 ACTUATOR_CONFIGURATION_3D_MODE_OFF = 3 # Permanently set the actuator (ESC) to non 3D mode (non-reversible thrust).
uint8 ACTUATOR_CONFIGURATION_SPIN_DIRECTION1 = 4 # Permanently set the actuator (ESC) to spin direction 1 (which can be clockwise or counter-clockwise).
uint8 ACTUATOR_CONFIGURATION_SPIN_DIRECTION2 = 5 # Permanently set the actuator (ESC) to spin direction 2 (opposite of direction 1).

uint8 PARACHUTE_ACTION_DISABLE = 0
uint8 PARACHUTE_ACTION_ENABLE = 1
uint8 PARACHUTE_ACTION_RELEASE = 2

uint8 FAILURE_UNIT_SENSOR_GYRO = 0
uint8 FAILURE_UNIT_SENSOR_ACCEL = 1
uint8 FAILURE_UNIT_SENSOR_MAG = 2
uint8 FAILURE_UNIT_SENSOR_BARO = 3
uint8 FAILURE_UNIT_SENSOR_GPS = 4
uint8 FAILURE_UNIT_SENSOR_OPTICAL_FLOW = 5
uint8 FAILURE_UNIT_SENSOR_VIO = 6
uint8 FAILURE_UNIT_SENSOR_DISTANCE_SENSOR = 7
uint8 FAILURE_UNIT_SENSOR_AIRSPEED = 8
uint8 FAILURE_UNIT_SYSTEM_BATTERY = 100
uint8 FAILURE_UNIT_SYSTEM_MOTOR = 101
uint8 FAILURE_UNIT_SYSTEM_SERVO = 102
uint8 FAILURE_UNIT_SYSTEM_AVOIDANCE = 103
uint8 FAILURE_UNIT_SYSTEM_RC_SIGNAL = 104
uint8 FAILURE_UNIT_SYSTEM_MAVLINK_SIGNAL = 105
uint8 FAILURE_UNIT_SYSTEM_ESC = 106
uint8 FAILURE_UNIT_SYSTEM_TRAFFIC_AVOIDANCE = 107
uint8 FAILURE_UNIT_DATALINK_LTE = 150
uint8 FAILURE_UNIT_DATALINK_WIFI = 151
uint8 FAILURE_UNIT_DATALINK_TELEM_RADIO = 152
uint8 FAILURE_UNIT_BUS_CAN = 200
uint8 FAILURE_UNIT_BUS_I2C = 201

uint8 FAILURE_TYPE_OK = 0
uint8 FAILURE_TYPE_OFF = 1
uint8 FAILURE_TYPE_STUCK = 2
uint8 FAILURE_TYPE_GARBAGE = 3
uint8 FAILURE_TYPE_WRONG = 4
uint8 FAILURE_TYPE_SLOW = 5
uint8 FAILURE_TYPE_DELAYED = 6
uint8 FAILURE_TYPE_INTERMITTENT = 7
uint8 FAILURE_TYPE_DRIFT = 8

# Used as param1 in DO_CHANGE_SPEED command.
uint8 SPEED_TYPE_AIRSPEED = 0
uint8 SPEED_TYPE_GROUNDSPEED = 1
uint8 SPEED_TYPE_CLIMB_SPEED = 2
uint8 SPEED_TYPE_DESCEND_SPEED = 3

# Used as param3 in CMD_DO_ORBIT.
uint8 ORBIT_YAW_BEHAVIOUR_HOLD_FRONT_TO_CIRCLE_CENTER = 0
uint8 ORBIT_YAW_BEHAVIOUR_HOLD_INITIAL_HEADING = 1
uint8 ORBIT_YAW_BEHAVIOUR_UNCONTROLLED = 2
uint8 ORBIT_YAW_BEHAVIOUR_HOLD_FRONT_TANGENT_TO_CIRCLE = 3
uint8 ORBIT_YAW_BEHAVIOUR_RC_CONTROLLED = 4
uint8 ORBIT_YAW_BEHAVIOUR_UNCHANGED = 5

# Used as param1&2 in CMD_START_RX_PAIR.
uint8 RC_TYPE_SPEKTRUM = 0
uint8 RC_TYPE_CRSF = 1
uint8 RC_SUB_TYPE_SPEKTRUM_DSM2 = 0
uint8 RC_SUB_TYPE_SPEKTRUM_DSMX = 1
uint8 RC_SUB_TYPE_SPEKTRUM_DSMX8 = 2

# Used as param1 in ARM_DISARM command.
int8 ARMING_ACTION_DISARM = 0
int8 ARMING_ACTION_ARM = 1

# param2 in VEHICLE_CMD_DO_GRIPPER.
uint8 GRIPPER_ACTION_RELEASE = 0
uint8 GRIPPER_ACTION_GRAB = 1

# Used as param1 in DO_SET_SAFETY_SWITCH_STATE command (matches MAVLink SAFETY_SWITCH_STATE enum).
uint8 SAFETY_SAFE = 0 # Activate safety (MAVLink SAFETY_SWITCH_STATE_SAFE)
uint8 SAFETY_DANGEROUS = 1 # Deactivate safety (MAVLink SAFETY_SWITCH_STATE_DANGEROUS)

# param1 in VEHICLE_CMD_ACTUATOR_GROUP_TEST (matches MAVLink ACTUATOR_TEST_GROUP enum)
uint8 ACTUATOR_TEST_GROUP_ROLL_TORQUE = 0
uint8 ACTUATOR_TEST_GROUP_PITCH_TORQUE = 1
uint8 ACTUATOR_TEST_GROUP_YAW_TORQUE = 2
uint8 ACTUATOR_TEST_GROUP_COLLECTIVE_TILT = 3
uint8 ACTUATOR_TEST_GROUP_X_THRUST = 4
uint8 ACTUATOR_TEST_GROUP_Y_THRUST = 5
uint8 ACTUATOR_TEST_GROUP_Z_THRUST = 6

uint8 ORB_QUEUE_LENGTH = 8

float32 param1 # Parameter 1, as defined by MAVLink uint16 VEHICLE_CMD enum.
float32 param2 # Parameter 2, as defined by MAVLink uint16 VEHICLE_CMD enum.
float32 param3 # Parameter 3, as defined by MAVLink uint16 VEHICLE_CMD enum.
float32 param4 # Parameter 4, as defined by MAVLink uint16 VEHICLE_CMD enum.
float64 param5 # Parameter 5, as defined by MAVLink uint16 VEHICLE_CMD enum.
float64 param6 # Parameter 6, as defined by MAVLink uint16 VEHICLE_CMD enum.
float32 param7 # Parameter 7, as defined by MAVLink uint16 VEHICLE_CMD enum.
uint32 command # Command ID.
uint8 target_system # System which should execute the command.
uint8 target_component # Component which should execute the command, 0 for all components.
uint8 source_system # System sending the command.
uint16 source_component # Component / mode executor sending the command.
uint8 confirmation # 0: First transmission of this command. 1-255: Confirmation transmissions (e.g. for kill command).
bool from_external

uint16 COMPONENT_MODE_EXECUTOR_START = 1000

# TOPICS vehicle_command gimbal_v1_command vehicle_command_mode_executor

:::