* feat(gps): Galileo HAS mode for the ZED-X20P and GPSDrivers bump
GPS_UBX_MODE 8 selects the new UBXMode::GalileoHAS. The receiver only
processes HAS while host corrections are off, which makes RTCM and SPARTN
from the autopilot dead input, so it is an explicit mode rather than a
default and the description says what it gives up.
The submodule bump also brings UBX-SEC-SIG jamming state for F9 HPG 1.51
and X20, where the MON-RF flag is deprecated and always 0, and stops the
F9P-L1L2 path from warning about a missing jamming monitor on 1.51.
Assisted-by: Claude:claude-fable-5
Signed-off-by: Jacob Dahl <dahl.jakejacob@gmail.com>
* feat(sensor_gps): report the correction protocol, not just RTCM status
The u-blox driver now reads UBX-RXM-COR, which covers RTCM3, SPARTN and
Galileo HAS, so rtcm_msg_used and rtcm_crc_failed no longer describe
only RTCM. They become corrections_msg_used and corrections_crc_failed,
and corrections_protocol says which protocol the last message was: the
only receiver-side confirmation that a SPARTN stream or HAS is actually
being consumed, and the first time either field has moved on an X20.
Assisted-by: Claude:claude-fable-5
Signed-off-by: Jacob Dahl <dahl.jakejacob@gmail.com>
---------
Signed-off-by: Jacob Dahl <dahl.jakejacob@gmail.com>
* sensors: move GPS antenna offsets to per-receiver parameters
Move antenna position configuration from the single EKF2_GPS_POS_X/Y/Z
parameter set into per-receiver SENS_GPS{0,1}_OFF{X,Y,Z} parameters in
the sensors module. Each offset slot is matched to a physical receiver
by device ID (SENS_GPS{0,1}_ID), falling back to uORB instance index
when no IDs are configured.
The antenna offset is now carried through the SensorGps uORB message
and blended alongside other GPS states when multi-receiver blending is
active, so EKF2 receives the correct lever arm for whichever receiver
(or weighted combination) is selected.
- Add antenna_offset_{x,y,z} fields to SensorGps.msg
- Remove EKF2_GPS_POS_X/Y/Z params; EKF2 reads offset from gnssSample
- Add SENS_GPS{0,1}_ID and SENS_GPS{0,1}_OFF{X,Y,Z} params (module.yaml)
- Blend antenna offsets in GpsBlending (weighted average)
- Add unit tests for single, blended, and failover antenna offset cases
- Migrate params.c to module.yaml for the vehicle_gps_position module
* sensors: gps_blending: add asymmetric weight and fallthrough offset tests
Add two additional antenna offset test cases:
- dualReceiverAsymmetricWeightAntennaOffset: verify that unequal eph
values produce correctly skewed blend weights (0.8/0.2) and that the
output antenna offset reflects the weighted average
- blendingFallthroughAntennaOffset: verify that when blending is enabled
but can_do_blending evaluates false (eph=0), the non-blending path
correctly assigns the selected receiver's antenna offset
* feat(param_translation): translate EKF2_GPS_POS_ to SENS_GPS0_OFF_
* fix(msgs): proper formatting
* chore(msg): 0 if invalid/unknown
* fix(ROMFS): migrate EKF2_GPS_POS_ params
* fix(docs): migrate EKF2_GPS_POS_ params
* fix(blending): unsigned param
* Update msg/SensorGps.msg
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* fix(sensors/gps): remove 'values:' tag in module.yaml
* fix(sensors/gps): unsigned instance index
* fix(blending): restore const on gps_blend_states()
Move antenna offset blending into blend_gps_data() where the
weights are computed, keeping gps_blend_states() const.
* fix(sensors/gps): fix msg annotation and restore SENS_GPS_PRIME values
Remove incorrect @invalid NaN annotation from antenna offset fields
(0.0 default is correct, not a sentinel). Restore values tag for
SENS_GPS_PRIME so QGC shows a dropdown.
* fix(gps_blending): fix pre-existing bug to clear _gps_updated flags
The loop iterates over i but always clears gps_select_index. The intent is to clear
all updated flags, but only the selected one gets cleared (N times)
* test(gps_blending): add stale update flag regression test
Having a generic interface over the GPS drivers makes dedicated
functionality for each driver harder. Move the Septentrio driver into
its own module under the `gnss` driver directory, and let it have its
own parameters for only the functionality it requires. This also helps
with adding new features because they only need to be implemented for
the driver that wants it, simplifying testing.
- update all msgs to be directly compatible with ROS2
- microdds_client improvements
- timesync
- reduced code size
- add to most default builds if we can afford it
- lots of other little changes
- purge fastrtps (I tried to save this multiple times, but kept hitting roadblocks)
