* docs(arkv6s): add flight controller documentation
Signed-off-by: Jacob Dahl <dahl.jakejacob@gmail.com>
* docs(arkv6s): add product photo and note single-IMU variant
Drop in docs/assets/flight_controller/arkv6s/ark_v6s_front.jpg
so the page renders the board photo it already references, and
align the intro with the upstream description by spelling out
that the V6S is the single-IMU variant of the V6X.
* docs(arkv6s): add bootloader UART note, fix arkv6x RAM typo
Add the bootloader serial port note (TELEM1-only in bootloader mode)
to the ARKV6S docs, matching the ARKV6X docs. Also fix the ARKV6X
MCU spec listing "1MB Flash" instead of "1MB RAM".
---------
Signed-off-by: Jacob Dahl <dahl.jakejacob@gmail.com>
* boards: corvon 743v1 support (Docs and LED alignment)
This PR addresses #24769 by providing the required official documentation, while simultaneously aligning the board's LED semantics entirely with the PX4 standard.
Key Changes:
- Add complete corvon 743v1 hardware documentation and manufacturer link.
- Fix LED out-of-bounds bug and strictly align RGB states to Pixhawk standard (LED_BLUE=0, LED_RED=1, LED_GREEN=3).
- Update bootloader pin config (hw_config.h) to use red LED for boot/error, and update pre-built bootloader.bin.
* Prettier and file reduce
* docs: address reviewer feedback & board ID fix
* Apply suggestion from @hamishwillee
Co-authored-by: Hamish Willee <hamishwillee@gmail.com>
* docs: resolve final reviewer feedback (PPM, Debug Port, Manufacturer List)
---------
Co-authored-by: Hamish Willee <hamishwillee@gmail.com>
Co-authored-by: Ramon Roche <mrpollo@gmail.com>
* Creating a base for grf lidar
* Serial Drive is working, need to work out distance publish
* WIP Getting Range Data in cm
* Working Rand Distance Values for GRF 250 and GRF500
* Review Changes
* Compiler fixes
* Update to date
* small update
* Fix typo and remover unused libs
* removing unused enum
* Update to the Documentation
* Fiving scaling issue
* update to the logic
* [Feature] Adding I2C driver for the GRF250 and GRF500 models (#26425)
* Adding the GRF I2C driver
* I2C Driver Working
* Removing a lot of unnecessary code
* fixing names
* Changing the i2c Driver to be in the lightware laser
* remove the old driver
* formatting fix
* Adding Ligthware GRF to documentation
* Update to the Documentation
* Ensuring sample_perf ends
* Updating Docs
* uavcannode: implement hardpoint commands (#26334)
* implement cannode hardpoint commands
Signed-off-by: dirksavage88 <dirksavage88@gmail.com>
* Update src/drivers/uavcannode/Subscribers/HardpointCommand.hpp
Co-authored-by: Jacob Dahl <37091262+dakejahl@users.noreply.github.com>
* Update src/drivers/uavcannode/Subscribers/HardpointCommand.hpp
Co-authored-by: Jacob Dahl <37091262+dakejahl@users.noreply.github.com>
* add hardpoint sub to ark cannode, simplify handling of hardpoint broadcast
Signed-off-by: dirksavage88 <dirksavage88@gmail.com>
---------
Signed-off-by: dirksavage88 <dirksavage88@gmail.com>
Co-authored-by: Jacob Dahl <37091262+dakejahl@users.noreply.github.com>
* voxl_esc: Limit frequency of UART passthru writes to 20Hz
* voxl2_io: Added UART passthru
* docs: update link for px4 ros2 interface lib python api docs
* estimator_interface: remove unused getter
* gnss_checks: always run strict checks on ground
With the goal to never take off if the GNSS solution is not fullfilling the configured requirements still not stopping to use it in case it degrades mid air.
* ekf2 unit-tests: adapt to strict GNSS checks on ground
* escCheck: rework online check to properly report offline ESCs
previous to this
09d79b221f
set `esc_online_flags` e.g. for UAVCAN ESCs which specific one is online and that then got compared to a mask where the first `esc_count` bits were set.
So if only ESC 5 is mapped and online you get the message "ESC 156 offline" because `esc_online_flags = 0b1000` gets compared to `online_bitmask = 0b1` based on `esc_count = 1` and the motor index is `esc[0].actuator_function = 0` wrapped using `0 - actuator_motors_s::ACTUATOR_FUNCTION_MOTOR1 + 1 = 156`.
* FailureDetector: consistent timestamp naming
* FailureDetector: rework motor status check
* FailureDetector: implement upper and lower current limit with offset
* Update src/modules/commander/failure_detector/FailureDetector.cpp
Prevent Buffer overflow
* Update Format
* Subedit
* Shrink and rename image
* Apply suggestion from @hamishwillee
Sounds good
Co-authored-by: Hamish Willee <hamishwillee@gmail.com>
* Apply suggestion from @hamishwillee
More universal approach
Co-authored-by: Hamish Willee <hamishwillee@gmail.com>
* Update to the Documentation
* FailureDetector: rework motor status check
* FailureDetector: implement upper and lower current limit with offset
* Subedit
* docs: update parameter reference metadata
* Remove pregenerated files - that should all be tidied up next time this runs
* remover GRF parameters
* Documentation updates
* Fixing Merge Conflicts
* remove @
* Undo Changes to parameter_reference
* remove the code that will be autogen-ed
* Update the Camake File
---------
Signed-off-by: dirksavage88 <dirksavage88@gmail.com>
Co-authored-by: Andrew Brahim <35986980+dirksavage88@users.noreply.github.com>
Co-authored-by: Jacob Dahl <37091262+dakejahl@users.noreply.github.com>
Co-authored-by: Eric Katzfey <eric.katzfey@modalai.com>
Co-authored-by: Beat Küng <beat-kueng@gmx.net>
Co-authored-by: Matthias Grob <maetugr@gmail.com>
Co-authored-by: Marco Hauswirth <marco.hauswirth@auterion.com>
Co-authored-by: Nick <145654544+ttechnick@users.noreply.github.com>
Co-authored-by: Hamish Willee <hamishwillee@gmail.com>
Co-authored-by: Ramon Roche <mrpollo@gmail.com>
* feat: implement UAVCAN LED control for individual light control and assignment
* uavcan led: nit-picks from review
* uavcan led: reduce maximum number of lights
to avoid unused parameters
* uavcan led: simplify anticolision on check
* uavcan led: correctly map 8-bit RGB to rgb565
* Trim param name character arrays to 17
16 characters + \0 termination
* uavcan led: final nit-picks
---------
Co-authored-by: Matthias Grob <maetugr@gmail.com>
* docs: modernize README with hero logo, vehicle icons, and fixed links
Add PX4 and Dronecode SVG logos to the repo, replace broken external
Dronecode logo URL, fix SITL badge branch from master to main, and
restructure the README with centered branding, airframe icon row,
quick-start section, and consolidated documentation links.
* moving raptor
bump
compiles and raptor mode appears
hovering with RAPTOR seems to work
Using Raptor to execute offboard commands works (using multirobot f03825a5795a77c5a095f799eeb8e0b646fe7176 to feed the trajectory_setpoint). Requires more testing
simplified rotmat
runtime inference frequency multiple
arming request response reflects actual readiness
adjusting to fit IMU gyro ratemax
relaxing control timing warning thresholds for SITL
Using mode registration to signal if offboard commands should be forwarded to trajectory_setpoint instead of just hardcoding vehicle_status.nav_state == vehicle_status_s::NAVIGATION_STATE_OFFBOARD
adopting new "request_offboard_setpoint" in raptor module
replace offboard seems good
mc_raptor: overwrite offboard parameter
separate raptor config
addendum
Raptor off by default
RAPTOR readme
Loading raptor checkpoint from tar works.
check if load was successful
refactoring: cutting out the pure C interface to allow direct testing of the policy input/output behavior from the file, without fully loading it into memory first
adapter not needed anymore
ripping out test observation mode (not used in a long time)
fixing warnings
bump RLtools to fix the remaining warnings
Loading RAPTOR checkpoint from sdcard seems to work on FMU-6C
embedding Raptor policy into flash works again
also printing checkpoint name when using the embedded policy
cleaner handling of the checkpoint name
back to reading from file
ripping out visual odometry checks
cleaner
more debug but no success
bump rlt
bump
pre next rebase
we can publish the no angvel update because we latch onto it with the scheduled work item anyways
this kind of runs on the 6c
still bad
SIH almost flying
saving stale traj setpoint yaw
new error. timestamp not the problem anymore
bump rlt; SIH works with executor
shaping up
bumping blob (include tar checkpoint)
cleaning up
fixing formatting
update readme
* moving raptor
bump
compiles and raptor mode appears
hovering with RAPTOR seems to work
Using Raptor to execute offboard commands works (using multirobot f03825a5795a77c5a095f799eeb8e0b646fe7176 to feed the trajectory_setpoint). Requires more testing
simplified rotmat
runtime inference frequency multiple
arming request response reflects actual readiness
adjusting to fit IMU gyro ratemax
relaxing control timing warning thresholds for SITL
Using mode registration to signal if offboard commands should be forwarded to trajectory_setpoint instead of just hardcoding vehicle_status.nav_state == vehicle_status_s::NAVIGATION_STATE_OFFBOARD
adopting new "request_offboard_setpoint" in raptor module
replace offboard seems good
mc_raptor: overwrite offboard parameter
separate raptor config
addendum
Raptor off by default
RAPTOR readme
Loading raptor checkpoint from tar works.
check if load was successful
refactoring: cutting out the pure C interface to allow direct testing of the policy input/output behavior from the file, without fully loading it into memory first
adapter not needed anymore
ripping out test observation mode (not used in a long time)
fixing warnings
bump RLtools to fix the remaining warnings
Loading RAPTOR checkpoint from sdcard seems to work on FMU-6C
embedding Raptor policy into flash works again
also printing checkpoint name when using the embedded policy
cleaner handling of the checkpoint name
back to reading from file
ripping out visual odometry checks
cleaner
more debug but no success
bump rlt
bump
pre next rebase
we can publish the no angvel update because we latch onto it with the scheduled work item anyways
this kind of runs on the 6c
still bad
SIH almost flying
saving stale traj setpoint yaw
new error. timestamp not the problem anymore
bump rlt; SIH works with executor
shaping up
bumping blob (include tar checkpoint)
cleaning up
fixing formatting
update readme
updating gitignore
* fixing format and declaring submodules as cmake dependencies
* adding uORB message documentation
* fixing comment alignment
* Adding option to restrict mc_raptor to not listen to the trajectory_setpoint (use the position and yaw at activation time as reference instead)
* bump RLtools; relax timing thresholds and adding real world readme
* smooth traj tracking performance
* Measuring trajectory_setpoint timing (providing stats in raptor_status); reverting accidental .gitignore modification
* More ideomatic way of setting the path to the policy checkpoint
* Reset trajectory_setpoint on raptor mode activation
* Adding internal trajectory generation (feeding trajectory_setpoint over Mavlink is too noisy). Quite agile trajectory tracking, good performance
* stable flight
* Update msg/versioned/RaptorInput.msg
Co-authored-by: Hamish Willee <hamishwillee@gmail.com>
* adopting message formatting conventions
* sort raptor.px4board
* Archiving RegisterExtComponentRequestV1.msg
* Add message versioning for VehicleStatus v2 and RegisterExtComponentRequest v2
* fixing formatting
* making internal reference configurable via command
* RAPTOR docs wip
* raptor internal reference documentation
* Finishing RAPTOR docs first draft
* adding logging instructions
* Fixing missing command documentation test error
* fixing format
* adding motor layout warning
* raptor minimal subedit - prettier, images etc
* Improve intro
* Fix up Neural_Networks version
* Mentioning "Adaptive" in the RAPTOR documentation's title
* Adding clarifications about the internal reference trajectory generator
* Removing "foundation policy" wording
* Fixing new-line check
* Removing redundant (evident through directory hierarchy) raptor_ from filenames
* Unifying Neural Network docs (mc_nn_control and mc_raptor) under the "Neural Network" topic
* Fix to standard structure
* Making the distinction between mc_nn_control and mc_raptor more clear and fixing the comparison table
* Removing trajectory_setpoint forwarding flag from external mode registration request and from the vehicle status
* Trivial layout and wording fixes
* fixing docs error
---------
Co-authored-by: Hamish Willee <hamishwillee@gmail.com>
Add PWM_*_CENTERx for each servo.
Use a bilinear transform to map actuator_servos to PWM signals.
This solution only works for PWM based servos. Other types of servos are not affected.
* PWM: Add servo trim option
* PWM: Improve documentation of PWM trim feature
* PWM: cleaner clamping and docs typo
* update documentation & safety
* add migration formula
* rename param from trim to center
* docs with center instead of trim
* move clamping and reorder values
* improve documentation
* adress failing range check
* improve documentation
* CA: add event for setting CENTER with TRIM
Signed-off-by: Silvan <silvan@auterion.com>
---------
Signed-off-by: Silvan <silvan@auterion.com>
Co-authored-by: Silvan <silvan@auterion.com>
* rc_update: remove 1% deadzone for all channels
this should be handled higher level.
* Remove all references to the RC{n}_DZ parameters
Regular expression: RC.{0,2}_DZ
---------
Co-authored-by: Jacob Dahl <37091262+dakejahl@users.noreply.github.com>
