* feat(sih): model the distance sensor range limits, quality and noise
The simulated distance sensor reported a noise free reading with no signal
quality, and saturated only against the upper range limit. Readings below the
minimum range were passed through unchanged, which is not what a range finder
does.
Report the raw saturated value with a zero quality outside of the measurement
range, derate the quality over the last 20% of the range, and add configurable
Gaussian noise (SIH_DISTSNSR_NOI). The quality is decided on the true distance
so that a measurement sitting at a range limit does not flicker in and out of
validity.
The sensor is now enabled with SIH_DISTSNSR_EN instead of by an out of band
value of the override parameter, and the ground distance computation moves into
a helper.
* feat(sih): add optical flow simulation
Simulate a downward facing optical flow sensor in SIH so that flow aided
navigation can be exercised without a rendered camera image. The flow rate is
the sum of the body rates and of the ground relative velocity scaled by the
distance to the ground, integrated over one publication interval and published
on sensor_optical_flow with configurable rate (SIH_OF_RATE) and noise
(SIH_OF_NOISE).
The sensor reports the integrated flow only: the flow module completes the
sample with the vehicle gyro and the downward facing distance sensor, which
therefore has to be enabled as well. Quality drops to zero above
SIH_OF_H_MAX or when the flow rate exceeds what the sensor can correlate.
The topic is advertised before the simulated clock starts, because the sensors
module brings up its flow pipeline on the first appearance of the topic, and
publishing during startup deadlocks the lockstep clock this thread advances.
Add the quadx_flow and standard_vtol_flow models with matching airframes:
SYS_AUTOSTART 10046 flies the multicopter on flow only with no GNSS, 10047
fuses the flow next to GNSS on a VTOL.
* prune configs
Signed-off-by: RomanBapst <bapstroman@gmail.com>
* more config cleanup
Signed-off-by: RomanBapst <bapstroman@gmail.com>
* added EKF2_HGT_REF to vtol flow config
Signed-off-by: RomanBapst <bapstroman@gmail.com>
* feat(simulation): added tests for optical flow for both quadx and stanard vtol
modes and enable them in CI
- for the test we monitor error on ground truth position and velocity
Signed-off-by: RomanBapst <bapstroman@gmail.com>
* feat(docs): document addition of optical flow in SIH
Signed-off-by: RomanBapst <bapstroman@gmail.com>
* fix(mavsdk_tests): unsubscribe flow ground truth comparison on destruction
The ground truth comparison callbacks capture `this` and touch members of
AutopilotTesterFlow. If a REQUIRE fails between start and stop, the tester
is destroyed during unwinding while the subscriptions are still active,
so a callback could run on the destroyed mutex and sample buffers.
Make stop idempotent and call it from the destructor, and stop any running
comparison before starting a new one.
Assisted-by: Claude:claude-opus-5-5
Signed-off-by: RomanBapst <bapstroman@gmail.com>
* tests for python
* fix(mavsdk_tests): start the VTOL flow loiter already on its radius
The loiter was centered on the vehicle's position right after the
transition, so it started at the center and had to fly straight out to the commanded
radius before the lateral guidance curved onto the track.
Assisted-by: Claude:claude-sonnet-5
* fix(mavsdk_tests): resend the flow test EKF origin until it is taken
The SITL startup script starts ekf2 after MAVLink. When MAVSDK connected
first, the single SET_GPS_GLOBAL_ORIGIN was published before ekf2 existed
and MAVSDK's RUN_PREARM_CHECKS followed it. Ekf2 then subscribed, saw
only the newest vehicle command and never got an origin. The Coverage
build starts slowly enough to hit this every time.
Assisted-by: Claude:claude-opus-5-5
* ci(sitl_tests): run the VTOL flow test without coverage
As a Coverage job it built with coverage on every PR and uploaded the
sitl-vtol flag from PRs, which replaced main's carried-forward VTOL
coverage with the flow-only flight. The quadx_flow entry also sat
between the Coverage comment and the standard_vtol entry it describes.
Assisted-by: Claude:claude-opus-5-5
* fix(mavsdk_tests): sum the flow test heading sweep with its sign
Adding up the absolute heading changes counted yaw oscillation toward the
360 degrees, so the wait could end before a full orbit was flown.
Assisted-by: Claude:claude-opus-5-5
* refactor(airframes): keep only the non-default params in the SIH flow airframes
SIH_OF_H_MAX, SIH_DISTSNSR_EN and EKF2_OF_CTRL were set to their defaults
and SENS_EN_GPSSIM is already set by the quadx base airframe. The quadx
forced EKF2_RNG_CTRL to 2 while the VTOL used the conditional default for
no stated reason, so both now use the default.
Assisted-by: Claude:claude-opus-5-5
* docs(sim_sih): mark the SIH flow airframes as new in PX4 v2.0
release/1.18 has branched, so these airframes first ship in v2.0, not
v1.17.
Assisted-by: Claude:claude-opus-5-5
---------
Signed-off-by: RomanBapst <bapstroman@gmail.com>
Co-authored-by: RomanBapst <bapstroman@gmail.com>
Co-authored-by: Jacob Dahl <dahl.jakejacob@gmail.com>
The 2.3 degree FoV published for the TFMINI/TFMINI-S dates back to
#24700 without a documented source and does not match the Benewake
datasheet, which specifies 2 degrees. Publish the datasheet value so
collision prevention and MAVLink consumers see an honest envelope.
Add the TFMINI Plus as variant 4. It speaks the same protocol but has
a 3.6 degree FoV and 0.1 m minimum range per the datasheet. Selecting
the TFMINI variant for a Plus made PX4 discard all readings below
0.4 m (signal_quality forced to 0), starving EKF2 of range aiding in
close-range use.
Update the PX4 docs so the model table, reported ranges and
out-of-range behaviour distinguish the two models.
Bench-verified on px4_fmu-v6x with a TFMINI Plus: variant 1 reports
h_fov 0.0349 rad and stamps quality 0 below 0.4 m; variant 4 reports
h_fov 0.0628 rad, keeps quality -1 from 0.11 to 0.30 m and stamps
quality 0 at 0.05 m.
Fixes#29460
Assisted-by: GLM:glm-5.3-flash
Signed-off-by: jiakun <53556221+ddwolf87@users.noreply.github.com>
The page predated the rangefinder page template: it had no specifications,
pinout, firmware support or testing sections, and claimed TFmini-i support,
although the TFmini-i only has RS-485 and CAN interfaces that the tfmini
driver can't read. The page now covers the TFmini-S and TFmini Plus, sourced
from Benewake's current datasheets and manuals and the driver, and the
rangefinder index lists each model.
Assisted-by: Claude:claude-opus-5-5
Signed-off-by: Hamish Willee <hamishwillee@gmail.com>
* docs(sensor): restructure Ainstein US-D1 rangefinder page
The page said the driver is not in most firmware and has to be started
from a configuration file. Neither is true: ulanding_radar is in the
common distance sensor set, and is started by SENS_ULAND_CFG.
Add specifications, mounting, pinout and wiring from the current
Ainstein manual, a Firmware Support section giving the board
configuration keys, and testing instructions. Remove the unsupported
NDAA tick from the rangefinder index and give the range as min-max.
Assisted-by: Claude:claude-opus-5-5
Signed-off-by: Hamish Willee <hamishwillee@gmail.com>
* Apply suggestion from @hamishwillee
---------
Signed-off-by: Hamish Willee <hamishwillee@gmail.com>
The page said the driver is usually present in firmware and gave its key
as drivers/ll40ls. That is only true for the I2C driver: the PWM
connection uses a separate driver, ll40ls_pwm, which is not in the
common distance sensor set.
Add a Firmware Support section covering both drivers, a supported models
table, specifications, pinout and I2C wiring from the Garmin v3 manual,
new I2C and PWM wiring diagrams, per-connection configuration with the
range PX4 uses, and testing instructions. Use Garmin's "LIDAR-Lite"
casing throughout.
Update the rangefinder index entry to match.
Assisted-by: Claude:claude-opus-5-5
Signed-off-by: Hamish Willee <hamishwillee@gmail.com>
* docs(msg_docs): sync uORB summary and remove stale pages
The link checker reported SensorsStatusGnss and VehicleGnssHeading as
missing from the table of contents, and SensorGps as an orphan.
SensorGps and EstimatorGpsStatus document messages that no longer exist
(renamed to SensorGnss in #24399 and removed in #28520), so the pages
are deleted. The uORB block in SUMMARY.md now matches the output of
Tools/msg/generate_msg_docs.py.
Assisted-by: Claude:claude-opus-5-5
Signed-off-by: Hamish Willee <hamishwillee@gmail.com>
* docs: fix external links reported by the link checker
Updates permanently redirected links to their targets, and points the
discontinued Bitcraze Crazyradio PA and Z-ranger deck v2 links at pages
that still exist.
The 3DR Control N1 link is ignored for 6 months: the site serves a
certificate that does not cover its hostname, which only the vendor can
fix.
Assisted-by: Claude:claude-opus-5-5
Signed-off-by: Hamish Willee <hamishwillee@gmail.com>
* docs: remove orphaned images
The two ICE control diagrams were superseded by SVG versions, and the
jMAVSim screenshot was left behind when the jMAVSim docs were replaced
with SIH and Hawkeye. No page in any language references them.
Assisted-by: Claude:claude-opus-5-5
Signed-off-by: Hamish Willee <hamishwillee@gmail.com>
---------
Signed-off-by: Hamish Willee <hamishwillee@gmail.com>
* refactor(msg): rename SensorGps to SensorGnss and add VehicleGnss
GPS is one constellation; the receivers and the rest of PX4 handle GNSS. Field names lose their units (latitude, speed_accuracy, course, ...), which move into the metadata comments. The sensors module's output becomes VehicleGnss on vehicle_gnss: the selected receiver's sample next to what the sensors module adds to it (corrected sample time, antenna position, selected instance), so a consumer can tell the two apart and later selection and check results have a place to go.
Assisted-by: Claude:claude-opus-5-5
* refactor(drivers/gps): publish sensor_gnss
Follows the SensorGps to SensorGnss and vehicle_gps_position to VehicleGnss rename.
Assisted-by: Claude:claude-opus-5-5
* refactor(drivers/septentrio): publish sensor_gnss
Follows the SensorGps to SensorGnss and vehicle_gps_position to VehicleGnss rename.
Assisted-by: Claude:claude-opus-5-5
* refactor(drivers/pps_capture): read sensor_gnss
Follows the SensorGps to SensorGnss and vehicle_gps_position to VehicleGnss rename.
Assisted-by: Claude:claude-opus-5-5
* refactor(lib/gnss): select receivers on sensor_gnss
Follows the SensorGps to SensorGnss and vehicle_gps_position to VehicleGnss rename.
Assisted-by: Claude:claude-opus-5-5
* refactor(sensors): publish VehicleGnss on vehicle_gnss and rename SENS_GPS* to SENS_GNSS*
The sensors module's output nests the selected receiver's sample, with the corrected sample time, antenna position and selected instance next to it. SENS_GPS_MASK/TAU/PRIME and SENS_GPSn_ID/OFFX/OFFY/OFFZ/DELAY take the SENS_GNSS name the heading parameters already use; saved parameters migrate on import, and the EKF2_GPS_POS/EKF2_GPS_DELAY translations now land on the new names directly.
Assisted-by: Claude:claude-opus-5-5
* refactor(logger): log sensor_gnss and vehicle_gnss
Follows the SensorGps to SensorGnss and vehicle_gps_position to VehicleGnss rename.
Assisted-by: Claude:claude-opus-5-5
* refactor(ekf2): fuse vehicle_gnss
Follows the SensorGps to SensorGnss and vehicle_gps_position to VehicleGnss rename.
Assisted-by: Claude:claude-opus-5-5
* refactor(replay): replay vehicle_gnss
Follows the SensorGps to SensorGnss and vehicle_gps_position to VehicleGnss rename.
Assisted-by: Claude:claude-opus-5-5
* refactor(local_position_estimator): read vehicle_gnss
Follows the SensorGps to SensorGnss and vehicle_gps_position to VehicleGnss rename.
Assisted-by: Claude:claude-opus-5-5
* refactor(attitude_estimator_q): read vehicle_gnss
Follows the SensorGps to SensorGnss and vehicle_gps_position to VehicleGnss rename.
Assisted-by: Claude:claude-opus-5-5
* refactor(lib/terrain_estimation): take sensor_gnss
Follows the SensorGps to SensorGnss and vehicle_gps_position to VehicleGnss rename.
Assisted-by: Claude:claude-opus-5-5
* refactor(lib/wind_estimator): read vehicle_gnss in the replay script
Follows the SensorGps to SensorGnss and vehicle_gps_position to VehicleGnss rename.
Assisted-by: Claude:claude-opus-5-5
* refactor(vision_target_estimator): read vehicle_gnss
Follows the SensorGps to SensorGnss and vehicle_gps_position to VehicleGnss rename.
Assisted-by: Claude:claude-opus-5-5
* refactor(navigator): read vehicle_gnss
Follows the SensorGps to SensorGnss and vehicle_gps_position to VehicleGnss rename.
Assisted-by: Claude:claude-opus-5-5
* refactor(commander): read sensor_gnss and vehicle_gnss
Follows the SensorGps to SensorGnss and vehicle_gps_position to VehicleGnss rename.
Assisted-by: Claude:claude-opus-5-5
* refactor(mavlink): stream sensor_gnss and vehicle_gnss
Follows the SensorGps to SensorGnss and vehicle_gps_position to VehicleGnss rename.
Assisted-by: Claude:claude-opus-5-5
* refactor(uxrce_dds_client): bridge vehicle_gnss
Follows the SensorGps to SensorGnss and vehicle_gps_position to VehicleGnss rename.
Assisted-by: Claude:claude-opus-5-5
* refactor(zenoh): bridge vehicle_gnss
Follows the SensorGps to SensorGnss and vehicle_gps_position to VehicleGnss rename.
Assisted-by: Claude:claude-opus-5-5
* refactor(failure_injection): inject GNSS failures on sensor_gnss
Follows the SensorGps to SensorGnss and vehicle_gps_position to VehicleGnss rename.
Assisted-by: Claude:claude-opus-5-5
* refactor(drivers/ins): publish sensor_gnss
Follows the SensorGps to SensorGnss and vehicle_gps_position to VehicleGnss rename.
Assisted-by: Claude:claude-opus-5-5
* refactor(drivers/uavcan): publish sensor_gnss
Follows the SensorGps to SensorGnss and vehicle_gps_position to VehicleGnss rename.
Assisted-by: Claude:claude-opus-5-5
* refactor(drivers/uavcannode): read sensor_gnss
Follows the SensorGps to SensorGnss and vehicle_gps_position to VehicleGnss rename.
Assisted-by: Claude:claude-opus-5-5
* refactor(drivers/cyphal): bridge sensor_gnss
Follows the SensorGps to SensorGnss and vehicle_gps_position to VehicleGnss rename.
Assisted-by: Claude:claude-opus-5-5
* refactor(drivers/telemetry): read vehicle_gnss
Follows the SensorGps to SensorGnss and vehicle_gps_position to VehicleGnss rename.
Assisted-by: Claude:claude-opus-5-5
* refactor(drivers/rc): read vehicle_gnss for telemetry
Follows the SensorGps to SensorGnss and vehicle_gps_position to VehicleGnss rename.
Assisted-by: Claude:claude-opus-5-5
* refactor(drivers/osd): read vehicle_gnss
Follows the SensorGps to SensorGnss and vehicle_gps_position to VehicleGnss rename.
Assisted-by: Claude:claude-opus-5-5
* refactor(drivers/transponder): read sensor_gnss
Follows the SensorGps to SensorGnss and vehicle_gps_position to VehicleGnss rename.
Assisted-by: Claude:claude-opus-5-5
* refactor(boards/modalai): publish sensor_gnss from the voxl2 drivers
Follows the SensorGps to SensorGnss and vehicle_gps_position to VehicleGnss rename.
Assisted-by: Claude:claude-opus-5-5
* refactor(examples): publish sensor_gnss and read vehicle_gnss
Follows the SensorGps to SensorGnss and vehicle_gps_position to VehicleGnss rename.
Assisted-by: Claude:claude-opus-5-5
* refactor(simulation): publish sensor_gnss
Follows the SensorGps to SensorGnss and vehicle_gps_position to VehicleGnss rename.
Assisted-by: Claude:claude-opus-5-5
* refactor(gnss): name GNSS variables gnss in the sensors module and receiver drivers
GPS is one constellation. Identifiers that hold or handle GNSS samples, or bind to the renamed parameters, follow the message and parameter rename; classes, files, modules and names tied to parameters that keep GPS stay.
Assisted-by: Claude:claude-opus-5-5
* refactor(gnss): name GNSS variables gnss in the estimators and navigator
GPS is one constellation. Identifiers that hold or handle GNSS samples, or bind to the renamed parameters, follow the message and parameter rename; classes, files, modules and names tied to parameters that keep GPS stay.
Assisted-by: Claude:claude-opus-5-5
* refactor(gnss): name GNSS variables gnss in commander, mavlink and failure injection
GPS is one constellation. Identifiers that hold or handle GNSS samples, or bind to the renamed parameters, follow the message and parameter rename; classes, files, modules and names tied to parameters that keep GPS stay.
Assisted-by: Claude:claude-opus-5-5
* refactor(gnss): name GNSS variables gnss in the remaining drivers and simulation
GPS is one constellation. Identifiers that hold or handle GNSS samples, or bind to the renamed parameters, follow the message and parameter rename; classes, files, modules and names tied to parameters that keep GPS stay.
Assisted-by: Claude:claude-opus-5-5
* docs(gnss): reference sensor_gnss, vehicle_gnss and SENS_GNSS* parameters
The upgrade guide covers the topic, field, ROS 2, parameter and Cyphal register renames.
Assisted-by: Claude:claude-opus-5-5
* fix(boards): name EKF2::UpdateGnssSample in the fmu-v6xrt ITCM lists
The rename left the old UpdateGpsSample symbol in the lists, so the ITCM check fails and the function drops out of ITCM on the boards it doesn't check.
Assisted-by: Claude:claude-opus-5-5
* chore(drivers/gps): bump PX4-GPSDrivers to the merged sensor_gnss rename
The submodule pointed at the PX4-GPSDrivers#243 branch commit; #243 is merged.
Assisted-by: Claude:claude-opus-5-5
* docs(msg): restore WGS84 in SensorGnss and point VehicleGlobalPosition at vehicle_gnss
The rename dropped the only mention of the WGS84 datum and ellipsoid, and left VehicleGlobalPosition referring to the removed vehicle_gps_position topic.
Assisted-by: Claude:claude-opus-5-5
* refactor(msg): drop selected_instance from VehicleGnss
receiver.device_id already names the selected receiver, and 0 while blended. The sensor_gnss instance depends on the order drivers advertise at boot, so it doesn't identify a receiver across boots or logs, and nothing reads it. It would also be meaningless on the per-receiver VehicleGnss instances proposed in #28894.
Assisted-by: Claude:claude-opus-5-5
* refactor(gnss): fuse vehicle_gnss.timestamp_sample directly and document the receiver's corrected time
vehicle_gnss.timestamp is now the sensors module's publish time, so EKF2's check of timestamp_sample against it was always true; the sensors module always fills timestamp_sample. The message docs described receiver.timestamp_sample as the driver's uncorrected value, but the sensors module writes the corrected time into it as well.
Assisted-by: Claude:claude-opus-5-5
* docs(msg): point VehicleGnss users at the top-level timestamp_sample
uXRCE-DDS shifts only top-level timestamp and timestamp_sample into agent time, so receiver.timestamp_sample reaches ROS 2 on the PX4 boot clock even though it holds the same value on uORB.
Assisted-by: Claude:claude-opus-5-5
* docs(releases): tell ROS 2 users which VehicleGnss timestamps to read
Only top-level timestamps are converted to ROS time, so a port that reads receiver.timestamp gets the PX4 boot clock, and vehicle_gnss.timestamp is now the sensors module's publish time rather than the receiver's.
Assisted-by: Claude:claude-opus-5-5
* docs(msg): add missing uORB message pages to SUMMARY
The msg_docs block in SUMMARY.md is not regenerated by the metadata sync,
so seven message pages were unreachable from the sidebar (PageNotInTOC).
Replace the block with the fragment written by generate_msg_docs.py,
which also moves VehicleControlMode to the unversioned list.
Assisted-by: Claude:claude-opus-5-5
Signed-off-by: Hamish Willee <hamishwillee@gmail.com>
* docs: fix broken and permanently redirected external links
CUAV moved its docs to a /en/<product>/ layout, so the Nora, C-RTK 9Ps
and C-RTK2 links returned 404. Other vendor links (InvenSense, Bosch,
ARK, CORVON) permanently redirect; point them at the final URL.
Assisted-by: Claude:claude-opus-5-5
Signed-off-by: Hamish Willee <hamishwillee@gmail.com>
* docs: fix remaining dead external links
RaccoonLab's store product pages, the CubeNode pin descriptions,
wiki.ubuntu.com/LTS and the Bitbucket NuttX repos no longer resolve.
RaccoonLab now only has docs pages for these devices, so link those.
ubuntu.sh and macos.sh already install kconfig-frontends, so the NuttX
porting guide no longer tells Ubuntu users to build it from source; the
old steps are kept in a comment.
Assisted-by: Claude:claude-opus-5-5
Signed-off-by: Hamish Willee <hamishwillee@gmail.com>
* docs: ignore unresolvable external links for 6 months
These links fail the external link check for reasons a docs edit can't
fix: bot blocking (raccoonlab.co, gitlab.arm.com), expired vendor
certificates (svehicle.cn, jmarple.ai), and the ARKV6X-RT order link,
which is waiting on a replacement URL from ARK.
Assisted-by: Claude:claude-opus-5-5
Signed-off-by: Hamish Willee <hamishwillee@gmail.com>
---------
Signed-off-by: Hamish Willee <hamishwillee@gmail.com>
* docs(docs): Add missing uorb topics sidebar
* docs(docs): discontinue cuav v5 plus/nano
* docs(docs): Fix 404 and 303 status HTTP links
* docs(docs): more link fixes
* update(drivers): Docs fix to fix up link
* docs(docs): Fix up all remaining broken links and add exclusions
* Add Sony AS-DT1 Distance Sensor and Documentation
* Ensuring Rotation Parameter works
* Sony ASDT1 Sensor and Documentaiton
* Fixed formatting and added additional comments
* Forgot to stage 1 formatting issue
* fix(drivers): use AS-DT1 parameters consistently
remove the Sony-ASDT1 -R command line rotation, as well as some other small fixes. Updated the docs to reflect this as well.
* refactor(drivers): clarify Sony AS-DT1 variable names
---------
Co-authored-by: Sean Hickey <sean@ascendengineer.com>
Co-authored-by: Andrew Brahim <35986980+dirksavage88@users.noreply.github.com>
The flow output table shows forward movement producing +Y flow and
rightward movement producing -X flow, which confuses users whose sensors
have X-forward/Y-right coordinate systems. Add an info note explaining
that integrated flow values are angular rotations (radians) about the
body axes using the right-hand convention, which is why the axes are
cross-coupled with translational motion.
* Creating a base for grf lidar
* Serial Drive is working, need to work out distance publish
* WIP Getting Range Data in cm
* Working Rand Distance Values for GRF 250 and GRF500
* Review Changes
* Compiler fixes
* Update to date
* small update
* Fix typo and remover unused libs
* removing unused enum
* Update to the Documentation
* Fiving scaling issue
* update to the logic
* [Feature] Adding I2C driver for the GRF250 and GRF500 models (#26425)
* Adding the GRF I2C driver
* I2C Driver Working
* Removing a lot of unnecessary code
* fixing names
* Changing the i2c Driver to be in the lightware laser
* remove the old driver
* formatting fix
* Adding Ligthware GRF to documentation
* Update to the Documentation
* Ensuring sample_perf ends
* Updating Docs
* uavcannode: implement hardpoint commands (#26334)
* implement cannode hardpoint commands
Signed-off-by: dirksavage88 <dirksavage88@gmail.com>
* Update src/drivers/uavcannode/Subscribers/HardpointCommand.hpp
Co-authored-by: Jacob Dahl <37091262+dakejahl@users.noreply.github.com>
* Update src/drivers/uavcannode/Subscribers/HardpointCommand.hpp
Co-authored-by: Jacob Dahl <37091262+dakejahl@users.noreply.github.com>
* add hardpoint sub to ark cannode, simplify handling of hardpoint broadcast
Signed-off-by: dirksavage88 <dirksavage88@gmail.com>
---------
Signed-off-by: dirksavage88 <dirksavage88@gmail.com>
Co-authored-by: Jacob Dahl <37091262+dakejahl@users.noreply.github.com>
* voxl_esc: Limit frequency of UART passthru writes to 20Hz
* voxl2_io: Added UART passthru
* docs: update link for px4 ros2 interface lib python api docs
* estimator_interface: remove unused getter
* gnss_checks: always run strict checks on ground
With the goal to never take off if the GNSS solution is not fullfilling the configured requirements still not stopping to use it in case it degrades mid air.
* ekf2 unit-tests: adapt to strict GNSS checks on ground
* escCheck: rework online check to properly report offline ESCs
previous to this
09d79b221f
set `esc_online_flags` e.g. for UAVCAN ESCs which specific one is online and that then got compared to a mask where the first `esc_count` bits were set.
So if only ESC 5 is mapped and online you get the message "ESC 156 offline" because `esc_online_flags = 0b1000` gets compared to `online_bitmask = 0b1` based on `esc_count = 1` and the motor index is `esc[0].actuator_function = 0` wrapped using `0 - actuator_motors_s::ACTUATOR_FUNCTION_MOTOR1 + 1 = 156`.
* FailureDetector: consistent timestamp naming
* FailureDetector: rework motor status check
* FailureDetector: implement upper and lower current limit with offset
* Update src/modules/commander/failure_detector/FailureDetector.cpp
Prevent Buffer overflow
* Update Format
* Subedit
* Shrink and rename image
* Apply suggestion from @hamishwillee
Sounds good
Co-authored-by: Hamish Willee <hamishwillee@gmail.com>
* Apply suggestion from @hamishwillee
More universal approach
Co-authored-by: Hamish Willee <hamishwillee@gmail.com>
* Update to the Documentation
* FailureDetector: rework motor status check
* FailureDetector: implement upper and lower current limit with offset
* Subedit
* docs: update parameter reference metadata
* Remove pregenerated files - that should all be tidied up next time this runs
* remover GRF parameters
* Documentation updates
* Fixing Merge Conflicts
* remove @
* Undo Changes to parameter_reference
* remove the code that will be autogen-ed
* Update the Camake File
---------
Signed-off-by: dirksavage88 <dirksavage88@gmail.com>
Co-authored-by: Andrew Brahim <35986980+dirksavage88@users.noreply.github.com>
Co-authored-by: Jacob Dahl <37091262+dakejahl@users.noreply.github.com>
Co-authored-by: Eric Katzfey <eric.katzfey@modalai.com>
Co-authored-by: Beat Küng <beat-kueng@gmx.net>
Co-authored-by: Matthias Grob <maetugr@gmail.com>
Co-authored-by: Marco Hauswirth <marco.hauswirth@auterion.com>
Co-authored-by: Nick <145654544+ttechnick@users.noreply.github.com>
Co-authored-by: Hamish Willee <hamishwillee@gmail.com>
Co-authored-by: Ramon Roche <mrpollo@gmail.com>
* Adding the GRF I2C driver
* I2C Driver Working
* Removing a lot of unnecessary code
* fixing names
* Changing the i2c Driver to be in the lightware laser
* remove the old driver
* formatting fix
* Adding Ligthware GRF to documentation
Using the SF30/d with the legacy protocol caused a delay of the
measurements of ~1s. This is not the case with the binary protocol anymore.
The initialization sequence used for SF20/c did not work and is therefore
updated.
Tested on both SF20/c and SF30/d.
* Add new INS driver sbgECom
Implement sbgECom messages handling to provide IMU sensors, GNSS and EKF data to the autopilot
Be able to parametrize the serial port, baudrate and the communicating mode
Clone sbgECom library only if sbgecom support is enabled and apply a patch
Be able to send SBG Systems INS settings in several ways when starting sbgecom driver
* Fix sensor airspeed simulator units
* Fix HIGHRES_IMU pressure unit
* Allow HIGHRES_IMU to support 4 IMUs
* sbgECom: Add documentation
* Use submodule instead of fetching sbgECom using CMake
* Remove patch strategy
* Fix dates
* Remove patch file
* Update SBG dev type ID
Co-authored-by: Jacob Dahl <37091262+dakejahl@users.noreply.github.com>
---------
Co-authored-by: Samuel Toledano <samuel.toledano@sbg-systems.com>
Co-authored-by: Jacob Dahl <37091262+dakejahl@users.noreply.github.com>