Commit Graph
54 Commits
Author SHA1 Message Date
Henry Kotzé ff8f44e8e1 docs(mavlink): document the MAV_X_REMOTE_IP partner IP parameter (#29627) 2026-11-12 08:18:56 +11:00
Andrea Bernasconi 08f5938916 fix(failure_detector): check altitude loss without a height setpoint (#29000)
* fix(failure_detector): check altitude loss without a height setpoint

The altitude loss check only ran when an altitude setpoint was present.
While the pilot moves the throttle stick in Altitude/Position mode the
setpoint is NaN, so a failure during a manual climb or manual descent
was never detected.

When there is no height setpoint but a vertical velocity setpoint is
available, keep a reference that remembers the highest altitude reached
and only moves down at the commanded descent rate. Climb or hold
commands therefore protect the best height, and a commanded descent is
compared against the expected one with FD_ALT_LOSS as margin.

Assisted-by: Claude:claude-opus-5-5
Signed-off-by: Andrea Bernasconi <andrea.bernasconi@auterion.com>

* fix(failure_detector): ignore stale descent setpoint in altitude loss check

Without a height setpoint the reference is lowered by the commanded
descent rate. If position control stopped publishing while a descent
was commanded, the last vz was integrated indefinitely, lowering the
reference and masking the altitude loss the detector should catch.

Only integrate the commanded descent while the setpoint is fresh
(within 500 ms of the position estimate); otherwise the reference is
held at the best altitude reached.

Assisted-by: Claude:claude-opus-5-5
Signed-off-by: Andrea Bernasconi <andrea.bernasconi@auterion.com>

* docs(safety): describe altitude loss reference for manual commands

The altitude loss trigger is no longer measured only against an
altitude setpoint. Explain that manual climbs and descents are covered
and how a commanded descent lowers the reference.

Assisted-by: Claude:claude-opus-5-5
Signed-off-by: Andrea Bernasconi <andrea.bernasconi@auterion.com>

* fix(commander): Add a margin to avoid small error accumulation

* fix(failure_detector): keep the altitude loss reference when the setpoint follows the vehicle

In auto modes emergency braking keeps the altitude setpoint on the vehicle
while it falls. The setpoint dragged the reference down with it, and every
time it ended up just below the vehicle the reference was reset, so a free
fall during a mission was not detected.

The reference now only moves down at the commanded descent rate, and it is
kept while the vehicle falls faster than allowed even if it is above the
setpoint.

Assisted-by: Claude:claude-opus-5-5
Signed-off-by: Andrea Bernasconi <andrea.bernasconi@auterion.com>

* style(failure_detector): shorten altitude loss reference comment

Assisted-by: Claude:claude-opus-5-5
Signed-off-by: Andrea Bernasconi <andrea.bernasconi@auterion.com>

* style(failure_detector): name altitude loss constants as constants

Also document the 2 m/s descent rate margin.

Assisted-by: Claude:claude-opus-5-5
Signed-off-by: Andrea Bernasconi <andrea.bernasconi@auterion.com>

* fix(failure_detector): apply the descent rate margin once

The commanded descent rate already includes the margin, adding it again
meant a fall up to 2 m/s faster than the reference moves down, with the
setpoint kept on the vehicle, reset the reference instead of being
detected.

Assisted-by: Claude:claude-opus-5-5
Signed-off-by: Andrea Bernasconi <andrea.bernasconi@auterion.com>

---------

Signed-off-by: Andrea Bernasconi <andrea.bernasconi@auterion.com>
2026-11-04 17:59:05 +01:00
Jacob Dahlanddanielbuleandra ae7977f868 feat(dshot): log the ESC EEPROM dumps (#28800)
* fix(dshot): retry telemetry init until the motor mask is known

rc.serial issues `dshot telemetry` right after `dshot start`, and the first
Run() usually handles it before the mixer has reported the outputs.
initSettingsHandlers() then latches with an empty motor mask, so no ESC
settings handler is ever created and the EEPROM is never read.

Co-authored-by: danielbuleandra <daniel.buleandra@auterion.com>
Assisted-by: Claude:claude-fable-5-1
Signed-off-by: Jacob Dahl <dahl.jakejacob@gmail.com>

* feat(logger): log the ESC EEPROM dumps

The raw dump is logged through the existing queued esc_eeprom_read topic.
The layout depends on the ESC firmware and its EEPROM revision, so decoding
happens offline in Tools/esc_eeprom_decode.py against the schema the ESC
vendor publishes.

A subscriber that joins after the first publish only sees the newest queued
entry. The logger subscribes on a sweep that can lag a new topic by half a
second while all ESCs answer within milliseconds of each other, so the topic
is advertised when the settings handlers are created, well before the first
request goes out at ESC_INIT_TELEM_DELAY.

Co-authored-by: danielbuleandra <daniel.buleandra@auterion.com>
Assisted-by: Claude:claude-fable-5-1
Signed-off-by: Jacob Dahl <dahl.jakejacob@gmail.com>

* feat(dshot): publish and refresh cached ESC settings

Logs can start after boot or during flight, so cached settings must be published independently of arming. The queue must retain a complete set of ESC dumps for the logger and MAVLink stream.

Keep programming uninterrupted and cached data valid across saves and reconnects. Failed reads remain pending with spaced retries so one unresponsive ESC cannot starve the rest.

Signed-off-by: Jacob Dahl <dahl.jakejacob@gmail.com>
Assisted-by: Codex

* fix(tools): decode repeated ESC dumps across firmware layouts

Logs contain repeated dumps and may mix EEPROM layouts. Collapse unchanged samples, apply the schema's version bounds and disabled values, and keep overlays immutable so one ESC cannot change another's decoding.

Signed-off-by: Jacob Dahl <dahl.jakejacob@gmail.com>
Assisted-by: Codex

* fix(dshot): bound ESC settings read retries

A pending settings read blocks the telemetry round-robin until it completes or times out, and the retry spacing was kept per ESC. With several ESCs that never answer, reads ran back to back, telemetry went stale and the arming check reported every ESC offline.

Space retries across all ESCs, give up on one after three failed reads until it reconnects or is asked for again, and time a read out at 100 ms: AM32 answers within milliseconds of the sixth frame, and anything under the 400 ms arming-check window keeps telemetry fresh.

Assisted-by: Claude:claude-fable-5-1
Signed-off-by: Jacob Dahl <dahl.jakejacob@gmail.com>

* fix(dshot): keep programming active until the save is sent

The flag was cleared when the save command was queued, so it no longer guarded the save itself. Only the finished() gate in the vehicle command loop kept a CONFIGURE_ACTUATOR from replacing it. Clear the flag when the last save frame goes out so the guard covers the whole sequence.

Assisted-by: Claude:claude-fable-5-1
Signed-off-by: Jacob Dahl <dahl.jakejacob@gmail.com>

* fix(dshot): send each ESC EEPROM read once per MAVLink link

The once-a-second republish that keeps the dumps in every log also went out on every link with ESC_EEPROM configured, low-bandwidth ones included, one message per ESC per second. timestamp_sample records when a dump was read, so the stream forwards each read once per link and still reaches a link that connects later.

A motor waiting on an EDT retry or out of EDT attempts took the command slot without sending anything, so settings reads never ran while any ESC left EDT unconfirmed. Vehicle commands now wait for an outstanding settings read, which ends within 100 ms, instead of CONFIGURE_ACTUATOR being rejected.

Assisted-by: Claude:claude-opus-5-5

* fix(msg): queue one ESC EEPROM dump per esc_status ESC

The republish queues every cached dump at once, so the queue needs one entry per ESC and no more. DSHOT_MAX_MOTORS is capped at CONNECTED_ESC_MAX, and the static_assert in AM32Settings.cpp keeps the two in step.

Assisted-by: Claude:claude-opus-5-5

* fix(dshot): mark the settings save explicitly

Programming ended when any finished command carried the value 12, which the address and value frames do whenever they write offset 12 (active brake power) or a value of 12. The write then stopped part way, with the ESC still in programming mode and the next write resuming mid-sequence.

Assisted-by: Claude:claude-opus-5-5

* fix(dshot): keep settings requests and writes to configured motors

An all-ESC save requested settings for every motor slot, and the single-ESC request and write paths took any index below the motor limit. Reads only go to motors with a settings handler, so the other bits stayed pending in dshot status forever. A write to an index with no output was never sent, so the command never finished and blocked every later command and the serial telemetry until reboot.

Assisted-by: Claude:claude-opus-5-5

* docs(dshot): describe the logged ESC settings and their decoding

The page said the settings are only read at boot and only reach a ground station.

Assisted-by: Claude:claude-opus-5-5

* feat(dshot): set the ciclicity to 10s for eeprom logging

---------

Signed-off-by: Jacob Dahl <dahl.jakejacob@gmail.com>
Co-authored-by: danielbuleandra <daniel.buleandra@auterion.com>
2026-11-03 08:14:51 -07:00
Julian Oes 36919f8415 fix(mavlink): accept unsigned traffic only on traffic receiver links (#29488) 2026-10-31 10:49:24 -06:00
PhilandHamish Willee b798249a61 feat(tools): add mavlink_serial_bridge.py reference bridge application (#28782)
* feat(tools): add mavlink_serial_bridge.py reference bridge application

Implements the SERIAL_CONTROL bridge application described in the Bridge Application section of docs/en/uart/serial_passthrough.md: it connects to the vehicle over MAVLink, exposes a virtual serial port (PTY), and translates traffic bidirectionally for any passthrough-capable port (TEL/GPS/ESC bitbang). Existing ESC configuration/flashing tools and GPS/RTK utilities can point at the exposed PTY without native MAVLink support.

Also updates serial_passthrough.md to reference this implementation instead of only describing the pattern in the abstract.

Signed-off-by: Phil-Engljaehringer <philipp.engljahringer@auterion.com>

* fix: add send_serial_control function

* docs: document mavlink_serial_bridge.py usage and limits

Explain what the bridge supports and how to run it safely: the example
connection string only listened on loopback, and --setup reboots the
flight controller with motor outputs disabled without saying so.

Restore the DShot ESC Serial Passthrough section, which was commented
out until a bridge existed, and update the v1.18 and main release notes
so v1.18 users know the bridge on main works with their firmware.

Assisted-by: Claude:claude-opus-5-5
Signed-off-by: Hamish Willee <hamishwillee@gmail.com>

* fix: removed duplicated port-map

* fix: send_serial_control adjust padding

* fix: set target_system and target_component only once

* fix: implemented changes requested by alex

* fix: implemented changes requested by hamish

* fix: avoid indefinite loop waiting for heartbeat

* fix: no chunking in send function needed

* fix: add lock and avoid trailing 0x00 sent on shutdown

* docs: explained SWITCH <device_id> feature in docs

---------

Signed-off-by: Phil-Engljaehringer <philipp.engljahringer@auterion.com>
Signed-off-by: Hamish Willee <hamishwillee@gmail.com>
Co-authored-by: Hamish Willee <hamishwillee@gmail.com>
2026-10-02 10:37:42 +02:00
Serhat Aksun 8bdb4f238e fix(msp_osd): fix OSD_SYMBOLS parameter bitmask behavior and missing elements (#28182)
* fix(msp_osd): Make pitch and roll angle configurable from parameter

* fix(msp_osd): Add crosshairs

* fix(msp_osd): Add current draw and mah drawn also make avg cell voltage configurable

* fix(msp_osd): Add gps speed and show unused parameters

* docs(msp_osd): fix supported symbols

* fix(msp_osd): Initialize all variables in *_rendor_* functions.
2026-08-20 09:28:49 -06:00
Hamish Willee 8ed15e6b19 docs(docs): Fix broken external links (#28300)
* docs(docs): Fix external links and associated tidy
* docs(docs): Fix up sidebar discontinued convention
* docs(docs): Fix up alternate sidebar
2026-08-20 11:53:24 +10:00
maksimdrachovandHamish Willee da47a168a5 docs(gripper): add DroneCAN EPM setup guide (#28049)
* docs(gripper): add DroneCAN EPM setup guide

Signed-off-by: Maksim Drachov <maksim.drachov@outlook.com>

* docs(docs): subedit

* docs(dronecan): clarify gripper publications

* payload_deliverer: clarify gripper command type

* docs: convert FluxGrip image to PNG

* docs: fix FluxGrip image path

* Update src/modules/payload_deliverer/module.yaml

---------

Signed-off-by: Maksim Drachov <maksim.drachov@outlook.com>
Co-authored-by: Hamish Willee <hamishwillee@gmail.com>
2026-08-03 16:08:46 -07:00
PX4BuildBot 06d0e500b7 docs: auto-sync metadata [skip ci]
Co-Authored-By: PX4 BuildBot <bot@px4.io>
2026-07-23 20:34:01 +00:00
Anil KircalialiandClaudio Chies 03bf4a5e95 feat(commander): add failsafe for traffic avoidance system (#27887)
* feat(commander): add traffic avoidance system failsafe

* test(commander): add tests for traffic avoidance failsafe

* docs(parameters): add COM_ARM_TRAFF migration notes

* fix(failsafe): use a shared header instead of hard-coding enum literals

* fix(commander): clear stale traffic avoidance unhealthy flag when check disabled

* refactor(failsafe): rename failsafe_mode_params.h to failsafe_action_modes.h

* docs(adsb_flarm): fix formatting in traffic avoidance parameter table

---------

Co-authored-by: Claudio Chies <chiesc@chies.com>
2026-07-23 13:26:11 -07:00
PX4BuildBot fe71d3bec1 docs: auto-sync metadata [skip ci]
Co-Authored-By: PX4 BuildBot <bot@px4.io>
2026-07-13 22:23:01 +00:00
5ea3cf8cb9 feat(navigator): extend detect and avoid module to follow regulatory standards such as ASTM F3442 (#26815)
* feat(navigator): extend detect and avoid module to follow regulatory standards such as ASTM F3442

* docs(docs): minor subedit

* refactor(navigator): reduce flash by grouping notif into same events

* docs(daa): Improve docs readability with ::: details blocks

* fix(navigator): single event when on ground with conflict

* refactor(boards): increase flash length from 4M - 128k to 5M - 128k

* rework(general): define DAA standard at build with new CONFIG_NAVIGATOR_ADSB_F3442

* clean(navigator): minor changes to clean the PR

* feat(boards): add CONFIG_NAVIGATOR_ADSB_FAKE_TRAFFIC in visionTargetEstStatic.px4board

* rework(daa): reduce amount of abstractions and minor cleaning

* refactor(boards): allyes revert flash length to 4M-128K

* refactor(boards): allyes increase flash length to 5M-128K

* rework(daa): rework event notifications to improve clarity

* docs(docs): move details inside of ::: details block

* docs(docs): run npx prettier

* refactor(daa): avoid void mutator functions

* docs(docs): Improve Python helper to decode daa unique id

* rework(daa): move encoded id handling to the adsb lib and refactor on_active

* refactor(daa): naming and zero init

* fix(daa): move dataman dep from daa level to unit test level

* refactor(daa): define common daa_input and rework process_transponder_report

* fix(daa): remove stale todo

* refactor(daa): rename crosstrack_based_daa to crosstrack_standard

* refactor(daa): rename F34_ params to DAA_

* docs(docs): revert changes to autogenerated docs

* docs(docs): Add Detect And Avoid in index.md

* refactor(daa): update message on init failed

* refactor(daa): only publish most_urgent conflict once in on_active()

* refactor(daa): move conflict buffer handling in the adsb lib

* refactor(daa): move notifications into new class ConflictNotifier and only notify once per cycle

* refactor(daa): uninit _cycle_changes to store into .bss (and save flash)

* docs(docs): remove unused image link

* refactor(daa): move automated action policy to the adsb lib

* refactor(daa): move self detection into adsb lib as DaaTrafficFilter

* refactor(daa): minor changes in unit tests

* refactor(daa): merge DaaTrafficFilter and DaaEncoding

* fix(daa): fix CI by removing navigator from the DAA deps

* refactor(daa): reduce stack size

* fix(daa): advertise _fake_traffic_pub in constructor

* refactor(daa): Comments only,  simplify and reduce comments

* fix(daa): brief comment missing end star

* Disable CONFIG_NAVIGATOR_ADSB in ark_fpv_default board

* docs(docs): General clarifications and remove the 1.18 badge

* refactor(daa): cleaning

* refactor(daa): minor cleaning

* refactor(adsb): simplify conflict tracker assuming push_back cannot fail

* build(cmake): cleaner fix to protect regex alternations

* refactor(daa): Crosstrack, remove unit test requiring finite yaw (yaw not used by standard)

* refactor(daa): minor cleaning and fix callsign to uint64

---------

Co-authored-by: jonas <jonas.perolini@rigi.tech>
Co-authored-by: Hamish Willee <hamishwillee@gmail.com>
2026-07-13 16:14:42 -06:00
Phil-EngljaehringerandHamish Willee dc3636eed0 docs(docs): serial passthrough (#27654)
* feat: added docs

* feat: some more documentation

* fix: worked on docs again

* fix: added doc to summary.md

* fix: adjusted docs to requests

* docs(docs): Subedit

* feat: added release notes to 1.18.md

* docs(docs): subedit

---------

Co-authored-by: Hamish Willee <hamishwillee@gmail.com>
2026-06-24 17:20:46 +10:00
65be196b9b docs(rovers): add hiwonder rover airframes and setup guide (#27333)
* rover: add hiwonder rover airframes

* docs: hiwonder rovers setup guide

* docs(docs): compress images

* docs(docs): prettier

* docs(docs): subedit

* docs(rover): add back tip about custom firmware install

* docs(rover): detail the hiwonder build / enable instructions

* docs(rover): fix airframe typo for ackermann

* docs(docs): Improve firmware section

---------

Co-authored-by: chfriedrich98 <chfriedrich@student.ethz.ch>
Co-authored-by: Hamish Willee <hamishwillee@gmail.com>
Co-authored-by: Ramon Roche <mrpollo@gmail.com>
2026-05-21 15:51:52 -04:00
Matthias Grob fcb627f572 fix(commander): prevent arming if enabled parachute check fails 2026-05-18 09:40:09 +02:00
Hamish Willee 4caac66328 docs(update): Parachute enabled extended addition 2026-05-18 09:40:09 +02:00
Hamish Willee 7f5d7ccb1c docs(update): Subedit 2026-05-18 09:40:09 +02:00
gguidone 66a1ae9704 docs: add parachute health failsafe documentation
Update safety.md, peripherals/parachute.md, and releases/main.md to document the extended COM_PARACHUTE parameter and the new configurable in-flight failsafe behaviour.
2026-05-18 09:40:09 +02:00
Michael Fritscheandchfriedrich98 0932ad144b feat(drivers): add support for hiwonder 4 channel encoder motor module (#27229)
* driver: hiwonder encoder motor module

* fix(drivers): Change HiwonderEMM from CRTP API to non-template ModuleBase

* fix(drivers): exclude hiwonder_emm driver from sitl build, as it fails i2c dependencies

* feat(drivers, hiwonder4channel): add parameter update subsciption

* feat(drivers, hiwonder4channel): add requested changes of original PR

* fix(drivers, hiwonder4channel): add default in hiwonder_emm module.yaml

* fix(drivers, hiwonder4channel): formatting

* fix(drivers, hiwonder4channel): add the hiwonder driver to all px4board s that include the roboclaw driver

* cleanup(drivers, hiwonder4channel): update copyright year

* chore(drivers): move hiwonder driver startup call from rc.board_sensors to rc.rover

* chore(drivers): hiwonder 4 channel - improve HIWONDER_EMM_EN description

* chore(drivers): hiwonder4channel - move to int8 for internal speed values

* chore(drivers): hiwonder4channel - move unconfigurable value to initialization.

* chore(drivers): hiwonder4channel - add reboot_required to enable parameter

* chore(drivers): hiwonder4channel - add docs

---------

Co-authored-by: chfriedrich98 <chfriedrich@student.ethz.ch>
2026-05-13 15:09:39 +02:00
Claudio Chies f79de2b783 feat(docs): update parameter recommendations for PingRX setup (#26880) 2026-04-29 11:55:25 +10:00
Gennaro Guidone 1281dbd8ff docs(safety): add altitude loss detection failsafe documentation (#27104) 2026-04-23 14:16:32 +10:00
PX4BuildBot 022f0119c0 docs: auto-sync metadata [skip ci]
Co-Authored-By: PX4 BuildBot <bot@px4.io>
2026-04-23 01:57:52 +00:00
Jacob Dahl c459caaa2a docs(peripherals): add On-Screen Display (OSD) page (#27134) 2026-04-23 11:50:09 +10:00
Hamish Willee c55267107a docs(update) - subedit 2026-04-21 10:42:57 +02:00
gguidone 4fee468f3f docs: add Remote ID in-flight failsafe documentation
Update safety.md, remote_id.md, and releases/main.md to document the extended COM_ARM_ODID parameter  and the new in-flight failsafe behaviour that will be introduced in PX4 v1.18.
2026-04-21 10:42:57 +02:00
Hamish Willee 4cbdc3dec6 docs(updates): Link fixes and orphan image removals (#26925)
* docs(updates): Link fixes and orphan image removals
* docs(delete): Remove orphaned translations
2026-04-01 13:51:06 +11:00
Hamish Willee a91037705c docs(mavlink): MAVLink Profiles - separate topic (#26816) 2026-03-19 13:32:30 +11:00
Jacob Dahl f00e46f618 feat(dshot): Extended Telemetry and EEPROM support
Overhauls the DShot driver with per-timer BDShot selection, multi-timer                                                                                                                                  
sequential capture, Extended DShot Telemetry (EDT), and AM32 ESC EEPROM                                                                                                                                  
read/write via MAVLink. Expands ESC support from 8 to 12 channels.                                                                                                                                       
                                                                                                                                                                                                   
BDShot:                                                                                                                                                                                                  
- Per-timer BDShot protocol selection via actuator config UI                                                                                                                                             
- Multi-timer sequential burst/capture on any DMA-capable timer                                                                                                                                          
- Adaptive per-channel GCR bitstream decoding                                                                                                                                                            
- Per-channel online/offline detection with hysteresis                                                                                                                                                   
                                                                                                                                                                                                   
Extended DShot Telemetry (EDT):                                                                                                                                                                          
- Temperature, voltage, current from BDShot frames (no serial wire)                                                                                                                                      
- New DSHOT_BIDIR_EDT parameter                                                                                                                                     
- EDT data merged with serial telemetry when both available                                                                                                                                              
                                                                                                                                                                                                   
AM32 EEPROM:                                                                                                                                                                                             
- Read/write AM32 ESC settings via MAVLink ESC_EEPROM message                                                                                                                                            
- ESCSettingsInterface abstraction for future ESC firmware types                                                                                                                                         
- New DSHOT_ESC_TYPE parameter                                                                                                                                                                           
                                                                                                                                                                                                   
Other changes:                                                                                                                                                                                           
- Per-motor pole count params DSHOT_MOT_POL1–12 (replaces MOT_POLE_COUNT)                                                                                                                              
- EscStatus/EscReport expanded to 12 ESCs with uint16 bitmasks                                                                                                                                           
- Numerous bounds-check, overflow, and concurrency fixes                                                                                                                                                 
- Updated DShot documentation
2026-03-17 16:38:33 -08:00
Hamish Willee b37733459d docs: Codespell check on English sources + swd fixes (#26657) 2026-03-05 12:50:59 +11:00
Hamish Willee 040b885dbd docs: DroneCAN Lights (#26641) 2026-03-05 10:43:41 +11:00
Hamish Willee 2fd131d3cf Link fixes 4 (#26633)
* Airframe - replace Babyshark with QAV250

* Link fixes
2026-03-04 09:45:50 +11:00
Hamish Willee 209c971c1b docs: Link fixes in docs - including 404 fixes (#26605)
* Redirect 301/308 HTTP link fixes
* Easy 404 fixes - easy
* Add internal anchor fixes and generate msg docs fix
2026-02-28 17:09:53 +11:00
PX4BuildBot 70a84a0c1b docs: auto-sync metadata [skip ci]
Co-Authored-By: PX4 BuildBot <bot@px4.io>
2026-02-18 16:45:17 +00:00
05de941399 Add Traffic Avoidance System (ADSB/FLARM) Arming Check (#26390)
* Add traffic avoidance system checks

* Update msg/px4_msgs_old/msg/VehicleStatusV1.msg

Co-authored-by: Hamish Willee <hamishwillee@gmail.com>

* docs: add arming check for traffic avoidance systems in ADS-B/FLARM documentation

* fix formating

* trafficAvoidanceCheck: switch case for configuration options

---------

Co-authored-by: Hamish Willee <hamishwillee@gmail.com>
Co-authored-by: Matthias Grob <maetugr@gmail.com>
2026-02-18 17:37:03 +01:00
PX4BuildBot 4bebbbae93 docs: auto-sync metadata [skip ci]
Co-Authored-By: PX4 BuildBot <bot@px4.io>
2026-02-16 17:47:30 +00:00
Claudio ChiesandMatthias Grob e52ce5c43b UAVCAN: Configurable LED Light Control with Flexible Addressing (#26253)
* feat: implement UAVCAN LED control for individual light control and assignment

* uavcan led: nit-picks from review

* uavcan led: reduce maximum number of lights

to avoid unused parameters

* uavcan led: simplify anticolision on check

* uavcan led: correctly map 8-bit RGB to rgb565

* Trim param name character arrays to 17

16 characters + \0 termination

* uavcan led: final nit-picks

---------

Co-authored-by: Matthias Grob <maetugr@gmail.com>
2026-02-16 18:39:48 +01:00
PX4BuildBot 36b5e1e1bb docs: auto-sync metadata [skip ci]
Co-Authored-By: PX4 BuildBot <bot@px4.io>
2026-02-11 22:43:01 +00:00
Claudio ChiesandHamish Willee f5c5f2ed8c Update FLARM link to the correct product page (#26361)
* Update FLARM link to the correct product page

* Update docs/en/peripherals/adsb_flarm.md

---------

Co-authored-by: Hamish Willee <hamishwillee@gmail.com>
2026-01-29 12:48:30 +11:00
Hamish Willee 1e34c80115 Minor link fix (#26196) 2026-01-02 17:50:17 +11:00
Hamish Willee 96f428b683 docs: Update metadata (#26167) 2025-12-24 14:57:46 +11:00
Patrik Dominik Pordi e01c4b0692 Ark esc docs + restructure top level ESC docs (#26132) 2025-12-18 10:28:34 +11:00
Jacob Dahl 463ddcab86 payload deliverer: remove PD_GRIPPER_EN as unnecessary, reduce gripper timeout to 1s 2025-07-28 11:25:17 -08:00
Hamish Willee 8e0f223b3a Link fixes and removal of dead docs (#25239)
* Remove Zubax Orel - not available and no other presence

* Fix up zubax product links

* Snapdragon flight - delete as no longer relevant hardware

* Delete intel aero docs

* Brushless whoop - remove docs except for link to old version

* Many link fixes
2025-07-17 15:30:56 +10:00
Hamish Willee 2c31e2bad5 Fix all possible HTTP to HTTPS docs links (#25153) 2025-07-03 18:09:58 +10:00
Hamish Willee 375f421c61 Link fixes galore (#25151) 2025-07-03 14:53:12 +10:00
Matthias Grob 2bc04f91f8 docs: fix all end of file newlines
Note: Some files are autogenerated and I did not yet
go through each source of generation to fix it there.
Instead I adjusted the filter to only exclude those
such that we can fix things in steps.
2025-06-26 11:03:23 -07:00
Hamish Willee 2e6fd9dd72 Updates from feedback 2025-06-20 08:27:03 +10:00
Hamish Willee 94dc757363 Prettier and add context 2025-06-20 08:27:03 +10:00
Hamish Willee 5cfa0d548c Update docs/en/peripherals/dshot.md 2025-06-20 08:27:03 +10:00
Jacob Dahl fa9f8734d0 update warning, add imxrt targets 2025-06-20 08:27:03 +10:00