* docs: add Integrated GCS page
* docs(config): fix review findings on Integrated GCS page
Integrated GCS units send manual control to PX4 either as MAVLink over
telemetry or as an RC signal (e.g. Herelink's S.Bus air unit output), so
the tip now covers both paths rather than pointing only to Joystick Setup.
Also lead the intro with the main benefit (manual and GCS control in one
unit), apply style-guide fixes, link the page from Manual Control, rename
the WebP images that had a .png extension, and compress the SRoC image.
Assisted-by: Claude:claude-opus-5-5
Signed-off-by: Hamish Willee <hamishwillee@gmail.com>
* Deleted unnescessary Aeronav Image: docs/assets/peripherals/integrated_gcs/uxv_technologies_aeronav.webp
* Delete unnescessary Micronav image: docs/assets/peripherals/integrated_gcs/uxv_technologies_micronav.webp
* docs(config): add PX4 configuration section to Integrated GCS page
The page listed devices but never said how to set PX4 up for one.
Configuration depends on whether the unit sends manual control as MAVLink
or as an RC signal, and with MAVLink control a single link loss triggers
both the manual control and data link loss failsafes, so the new section
covers manual control, telemetry, failsafes, arming and video for both.
Also crop the G2Nav image, drop the Alpha G-Case Duo at the author's
suggestion, and link the page from the config index, Joystick Setup,
Basic Concepts and the RC receiver list.
Assisted-by: Claude:claude-opus-5-5
Signed-off-by: Hamish Willee <hamishwillee@gmail.com>
---------
Signed-off-by: Hamish Willee <hamishwillee@gmail.com>
Co-authored-by: Hamish Willee <hamishwillee@gmail.com>
* feat(commander): only report safety button as available when it is available and configured to be used via COM_PREARM_MODE
* feat(commander): add a new option to COM_PREARM_MODE to explicitly and exclusively allow prearming via VEHICLE_CMD_DO_SET_SAFETY_SWITCH_STATE
* feat(commander): explicit dedicated safety-button-only and mavlink-only prearm modes
* fix(commander): also accept VEHICLE_CMD_DO_SET_SAFETY_SWITCH_STATE on Always and Disarmed pre-arm profiles to match documentation
* docs(prearm): update docs with new prearm mode behaviour
* fix(commander): fix syntax for bool
* docs(prearm): revert last param table, as COM_FORCE_SAFETY is already mentioned in a table above.
* docs(prearm): fix MAVLink spelling, grammar and parameter table
Make the pre-arm docs consistent with the COM_PREARM_MODE parameter and
the docs style guide: MAVLink is spelled consistently (page and option
labels), selectable option names are shown in code style, the parameter
table lists all five COM_PREARM_MODE options with the correct default,
and sentences are fixed and put one per line.
Question for the author: the COM_PREARM_MODE option labels say "Safety
button", while the docs say "safety switch". Are these synonyms? If so,
which term should we use in both places? If not, what is the difference?
Assisted-by: Claude:claude-opus-5-5
Signed-off-by: Hamish Willee <hamishwillee@gmail.com>
* fix(commander): clean up _button_disabled logic: button still needs to be enabled in Disabled and Always prearmed modes to switch safety off.
* docs(prearm): adjust COM_PREARM_MODE description and clarify/fix/improve prearm docs
* chore(VehicleCommand.msg): improved comments
* chore(msg): v0->v1 translation for VehicleCommand.msg
* Revert "chore(msg): v0->v1 translation for VehicleCommand.msg"
This reverts commit 50ea14fc76310ba7b53ebcd1c6ee8cf4e1c0776b.
* feat(commander): deny VEHICLE_CMD_DO_SET_SAFETY_SWITCH_STATE when not accepted
* feat(commander): COM_SAFETY_MODE replaces CBRK_IO_SAFETY
* docs(prearm): update docs with new COM_SAFETY_MODE behaviour
* docs(prearm): minor cleanup
* fix(commander): migrate CBRK_IO_SAFETY and correct safety ACKs
A stored CBRK_IO_SAFETY=0 was dropped on import, so upgraded vehicles booted with COM_SAFETY_MODE=0 and safety off. The CAN GPS nodes have no commander, so setting COM_SAFETY_MODE there only logged an error at boot. A SAFETY_SAFE command in mode 0 and ESC calibration with safety on were ACKed ACCEPTED while doing nothing.
Assisted-by: Claude:claude-opus-5-5
---------
Signed-off-by: Hamish Willee <hamishwillee@gmail.com>
Co-authored-by: Hamish Willee <hamishwillee@gmail.com>
Co-authored-by: Jacob Dahl <dahl.jakejacob@gmail.com>
* Remove Zubax Orel - not available and no other presence
* Fix up zubax product links
* Snapdragon flight - delete as no longer relevant hardware
* Delete intel aero docs
* Brushless whoop - remove docs except for link to old version
* Many link fixes
* Add vitepress tree
* Update existing workflows so they dont trigger on changes in the docs path
* Add nojekyll, package.json, LICENCE etc
* Add crowdin docs upload/download scripts
* Add docs flaw checker workflows
* Used docs prefix for docs workflows
* Crowdin obvious fixes
* ci: docs move to self hosted runner
runs on a beefy server for faster builds
Signed-off-by: Ramon Roche <mrpollo@gmail.com>
* ci: don't run build action for docs or ci changes
Signed-off-by: Ramon Roche <mrpollo@gmail.com>
* ci: update runners
Signed-off-by: Ramon Roche <mrpollo@gmail.com>
* Add docs/en
* Add docs assets and scripts
* Fix up editlinks to point to PX4 sources
* Download just the translations that are supported
* Add translation sources for zh, uk, ko
* Update latest tranlsation and uorb graphs
* update vitepress to latest
---------
Signed-off-by: Ramon Roche <mrpollo@gmail.com>
Co-authored-by: Ramon Roche <mrpollo@gmail.com>