* add files
* add corvon_V5 docs
docs: fix connectors image path
* docs: address Copilot formatting suggestions
* Subedit
* docs: add radio control wiring details for corvon_V5
* Update docs/en/flight_controller/corvon_V5.md
Co-authored-by: Hamish Willee <hamishwillee@gmail.com>
* boards/corvon: rename V5 subdirectory to v5
This renames the corvon_V5 board to corvon_v5 to conform to PX4 lowercase naming conventions as requested by @mrpollo. Renames target files, docs, and assets accordingly.
* Apply suggestion from @hamishwillee
Co-authored-by: Hamish Willee <hamishwillee@gmail.com>
* docs: add DSU7 debug port pinout and warnings for corvon_v5
This addresses reviewer feedback to include debug port information, placed immediately after the Radio Control section as requested.
* Apply suggestion from @hamishwillee
* fix(boards/corvon_v5): remove unused heater and temperature_compensation
- heater: board has no IMU heater; fixes build after #26325 (requires HEATER_NUM)
- temperature_compensation: modern IMU doesn't need it, follow #27015
Signed-off-by: holydust <holydust@live.ca>
* docs(update): Subedit. Add pwm outputs and gps
* Update docs/en/flight_controller/corvon_v5.md
* Update docs/en/flight_controller/corvon_v5.md
Co-authored-by: Hamish Willee <hamishwillee@gmail.com>
* docs(corvon_v5): add UART flow control, power details, fix broken links
* docs(corvon_v5): fix UART table typo
* fix(boards/corvon_v5): remove unused PX4IO macros. Board has no PX4IO co-processor
Signed-off-by: holydust <holydust@live.ca>
* Apply suggestions from code review
Co-authored-by: Hamish Willee <hamishwillee@gmail.com>
* docs(corvon_v5): update board images
Signed-off-by: holydust <holydust@live.ca>
* fix(corvon_v5): drop unused dshot, fix can3 and adc comments
- Remove CONFIG_DRIVERS_DSHOT=y from default.px4board: DShot is not
supported on this board (no IO timer is DShot-configured) and the
docs already state it as unsupported.
- Fix ADC1_IN8 GPIO list comment from PB8 to PB0 (PB0 is the correct
pin on STM32F765; matches GPIO_RSSI_IN definition below).
- Clarify CAN3 comment in nuttx-config board.h: the pins are unused
on CORVON_V5 (no transceiver populated). manifest.c already marks
CAN3 as not present.
- Update corvon_v5_pinout.xlsx 'All Pinouts' sheet so PA7 (HEATER)
and PA8/PA15/PH4 (CAN3 RX/TX/SILENT) read 'Unused', matching the
actual hardware.
Signed-off-by: holydust <holydust@live.ca>
* fix(corvon_v5): use MCS Electronics USB VID/PID
Set VID/PID to 0x16D0/0x152A (MCS Electronics) in the app defconfig
and regenerate the bootloader binary, replacing the 3DR FMUv5 IDs
inherited from the reference config.
Signed-off-by: holydust <holydust@live.ca>
---------
Signed-off-by: holydust <holydust@live.ca>
Co-authored-by: Hamish Willee <hamishwillee@gmail.com>
Add hardware documentation for the VOLOLAND NarinFC-H7 flight controller
including pinouts, serial port mapping, PWM output groups, and analog
inputs. Fix version badge to v1.17 and clarify RC_IN is wired directly
to FMU via RC_INPUT driver.
Based on work by @vololand and @hamishwillee from PR #26542.
Signed-off-by: Ramon Roche <mrpollo@gmail.com>
* feat(boards): add CBUnmanned H753-Stamp flight controller
* Update board_id to 1302
* docs: update CBUnmanned H753-Stamp board docs
Apply review feedback: correct the I2C bus count (add internal bus),
clarify SPI (IMUs on a dedicated internal bus), note the debug console
alongside the user UARTs, and describe how the board is powered from an
external 5 V supply with separate battery voltage sensing.
Add the pinout image and a PWM Outputs section.
Signed-off-by: Julian Oes <julian@oes.ch>
* refactor(boards): rename CBUnmanned H753-Stamp to H753-SOM
Rename the board directory, build target (cbunmanned_h753-som), USB
product strings, docs page, asset directory and pinout image, and the
bundled bootloader binary from -Stamp to -SOM. The hardware is a
System-on-Module, so SOM is the accurate name.
Signed-off-by: Julian Oes <julian@oes.ch>
---------
Signed-off-by: Julian Oes <julian@oes.ch>
* docs(arkv6s): add flight controller documentation
Signed-off-by: Jacob Dahl <dahl.jakejacob@gmail.com>
* docs(arkv6s): add product photo and note single-IMU variant
Drop in docs/assets/flight_controller/arkv6s/ark_v6s_front.jpg
so the page renders the board photo it already references, and
align the intro with the upstream description by spelling out
that the V6S is the single-IMU variant of the V6X.
* docs(arkv6s): add bootloader UART note, fix arkv6x RAM typo
Add the bootloader serial port note (TELEM1-only in bootloader mode)
to the ARKV6S docs, matching the ARKV6X docs. Also fix the ARKV6X
MCU spec listing "1MB Flash" instead of "1MB RAM".
---------
Signed-off-by: Jacob Dahl <dahl.jakejacob@gmail.com>
* boards: corvon 743v1 support (Docs and LED alignment)
This PR addresses #24769 by providing the required official documentation, while simultaneously aligning the board's LED semantics entirely with the PX4 standard.
Key Changes:
- Add complete corvon 743v1 hardware documentation and manufacturer link.
- Fix LED out-of-bounds bug and strictly align RGB states to Pixhawk standard (LED_BLUE=0, LED_RED=1, LED_GREEN=3).
- Update bootloader pin config (hw_config.h) to use red LED for boot/error, and update pre-built bootloader.bin.
* Prettier and file reduce
* docs: address reviewer feedback & board ID fix
* Apply suggestion from @hamishwillee
Co-authored-by: Hamish Willee <hamishwillee@gmail.com>
* docs: resolve final reviewer feedback (PPM, Debug Port, Manufacturer List)
---------
Co-authored-by: Hamish Willee <hamishwillee@gmail.com>
Co-authored-by: Ramon Roche <mrpollo@gmail.com>
* hrt: Fix PPM input on channel 2
The CCMR1_PPM define for PPM input on channel 2 was incorrectly set to 2,
which was setting bits for channel 1 instead of channel 2. This prevented
PPM input from functioning properly on channel 2.
Changed CCMR1_PPM for channel 2 from 2 to (1 << 8), which correctly
configures the CC2S bits for input capture mode on TI2.
This fixes an issue noted in the existing code comment:
"FIXME! There is an interaction in the CCMR registers that prevents
using Chan 1 as the timer and chan 2 as the PPM"
Tested on STM32H743 with PPM input on PC7 (TIM8_CH2).
* rc_input: enable sharing serial and PPM pin
By setting RC_SERIAL_PORT_SHARED_PPM_PIN_GPIO_RX it is now possible to
use the same pin on the STM32 for PPM input as well as serial input.
* boards: Add support for Holybro KakuteH7-Wing
* Add vitepress tree
* Update existing workflows so they dont trigger on changes in the docs path
* Add nojekyll, package.json, LICENCE etc
* Add crowdin docs upload/download scripts
* Add docs flaw checker workflows
* Used docs prefix for docs workflows
* Crowdin obvious fixes
* ci: docs move to self hosted runner
runs on a beefy server for faster builds
Signed-off-by: Ramon Roche <mrpollo@gmail.com>
* ci: don't run build action for docs or ci changes
Signed-off-by: Ramon Roche <mrpollo@gmail.com>
* ci: update runners
Signed-off-by: Ramon Roche <mrpollo@gmail.com>
* Add docs/en
* Add docs assets and scripts
* Fix up editlinks to point to PX4 sources
* Download just the translations that are supported
* Add translation sources for zh, uk, ko
* Update latest tranlsation and uorb graphs
* update vitepress to latest
---------
Signed-off-by: Ramon Roche <mrpollo@gmail.com>
Co-authored-by: Ramon Roche <mrpollo@gmail.com>
