Peripheral nodes that only have a CAN connection expose no serial debug
port, so their NSH console is reachable only through the
uavcan.protocol.AccessCommandShell service served by the uavcannode
driver. Document how to open that shell, its options and keys, and its
limitations (one session per node, last_exit_status), and link it from
the consoles overview and the docs sidebar.
Signed-off-by: danielbuleandra <daniel.buleandra@auterion.com>
Co-authored-by: Hamish Willee <hamishwillee@gmail.com>
* refactor(msg): rename SensorGps to SensorGnss and add VehicleGnss
GPS is one constellation; the receivers and the rest of PX4 handle GNSS. Field names lose their units (latitude, speed_accuracy, course, ...), which move into the metadata comments. The sensors module's output becomes VehicleGnss on vehicle_gnss: the selected receiver's sample next to what the sensors module adds to it (corrected sample time, antenna position, selected instance), so a consumer can tell the two apart and later selection and check results have a place to go.
Assisted-by: Claude:claude-opus-5-5
* refactor(drivers/gps): publish sensor_gnss
Follows the SensorGps to SensorGnss and vehicle_gps_position to VehicleGnss rename.
Assisted-by: Claude:claude-opus-5-5
* refactor(drivers/septentrio): publish sensor_gnss
Follows the SensorGps to SensorGnss and vehicle_gps_position to VehicleGnss rename.
Assisted-by: Claude:claude-opus-5-5
* refactor(drivers/pps_capture): read sensor_gnss
Follows the SensorGps to SensorGnss and vehicle_gps_position to VehicleGnss rename.
Assisted-by: Claude:claude-opus-5-5
* refactor(lib/gnss): select receivers on sensor_gnss
Follows the SensorGps to SensorGnss and vehicle_gps_position to VehicleGnss rename.
Assisted-by: Claude:claude-opus-5-5
* refactor(sensors): publish VehicleGnss on vehicle_gnss and rename SENS_GPS* to SENS_GNSS*
The sensors module's output nests the selected receiver's sample, with the corrected sample time, antenna position and selected instance next to it. SENS_GPS_MASK/TAU/PRIME and SENS_GPSn_ID/OFFX/OFFY/OFFZ/DELAY take the SENS_GNSS name the heading parameters already use; saved parameters migrate on import, and the EKF2_GPS_POS/EKF2_GPS_DELAY translations now land on the new names directly.
Assisted-by: Claude:claude-opus-5-5
* refactor(logger): log sensor_gnss and vehicle_gnss
Follows the SensorGps to SensorGnss and vehicle_gps_position to VehicleGnss rename.
Assisted-by: Claude:claude-opus-5-5
* refactor(ekf2): fuse vehicle_gnss
Follows the SensorGps to SensorGnss and vehicle_gps_position to VehicleGnss rename.
Assisted-by: Claude:claude-opus-5-5
* refactor(replay): replay vehicle_gnss
Follows the SensorGps to SensorGnss and vehicle_gps_position to VehicleGnss rename.
Assisted-by: Claude:claude-opus-5-5
* refactor(local_position_estimator): read vehicle_gnss
Follows the SensorGps to SensorGnss and vehicle_gps_position to VehicleGnss rename.
Assisted-by: Claude:claude-opus-5-5
* refactor(attitude_estimator_q): read vehicle_gnss
Follows the SensorGps to SensorGnss and vehicle_gps_position to VehicleGnss rename.
Assisted-by: Claude:claude-opus-5-5
* refactor(lib/terrain_estimation): take sensor_gnss
Follows the SensorGps to SensorGnss and vehicle_gps_position to VehicleGnss rename.
Assisted-by: Claude:claude-opus-5-5
* refactor(lib/wind_estimator): read vehicle_gnss in the replay script
Follows the SensorGps to SensorGnss and vehicle_gps_position to VehicleGnss rename.
Assisted-by: Claude:claude-opus-5-5
* refactor(vision_target_estimator): read vehicle_gnss
Follows the SensorGps to SensorGnss and vehicle_gps_position to VehicleGnss rename.
Assisted-by: Claude:claude-opus-5-5
* refactor(navigator): read vehicle_gnss
Follows the SensorGps to SensorGnss and vehicle_gps_position to VehicleGnss rename.
Assisted-by: Claude:claude-opus-5-5
* refactor(commander): read sensor_gnss and vehicle_gnss
Follows the SensorGps to SensorGnss and vehicle_gps_position to VehicleGnss rename.
Assisted-by: Claude:claude-opus-5-5
* refactor(mavlink): stream sensor_gnss and vehicle_gnss
Follows the SensorGps to SensorGnss and vehicle_gps_position to VehicleGnss rename.
Assisted-by: Claude:claude-opus-5-5
* refactor(uxrce_dds_client): bridge vehicle_gnss
Follows the SensorGps to SensorGnss and vehicle_gps_position to VehicleGnss rename.
Assisted-by: Claude:claude-opus-5-5
* refactor(zenoh): bridge vehicle_gnss
Follows the SensorGps to SensorGnss and vehicle_gps_position to VehicleGnss rename.
Assisted-by: Claude:claude-opus-5-5
* refactor(failure_injection): inject GNSS failures on sensor_gnss
Follows the SensorGps to SensorGnss and vehicle_gps_position to VehicleGnss rename.
Assisted-by: Claude:claude-opus-5-5
* refactor(drivers/ins): publish sensor_gnss
Follows the SensorGps to SensorGnss and vehicle_gps_position to VehicleGnss rename.
Assisted-by: Claude:claude-opus-5-5
* refactor(drivers/uavcan): publish sensor_gnss
Follows the SensorGps to SensorGnss and vehicle_gps_position to VehicleGnss rename.
Assisted-by: Claude:claude-opus-5-5
* refactor(drivers/uavcannode): read sensor_gnss
Follows the SensorGps to SensorGnss and vehicle_gps_position to VehicleGnss rename.
Assisted-by: Claude:claude-opus-5-5
* refactor(drivers/cyphal): bridge sensor_gnss
Follows the SensorGps to SensorGnss and vehicle_gps_position to VehicleGnss rename.
Assisted-by: Claude:claude-opus-5-5
* refactor(drivers/telemetry): read vehicle_gnss
Follows the SensorGps to SensorGnss and vehicle_gps_position to VehicleGnss rename.
Assisted-by: Claude:claude-opus-5-5
* refactor(drivers/rc): read vehicle_gnss for telemetry
Follows the SensorGps to SensorGnss and vehicle_gps_position to VehicleGnss rename.
Assisted-by: Claude:claude-opus-5-5
* refactor(drivers/osd): read vehicle_gnss
Follows the SensorGps to SensorGnss and vehicle_gps_position to VehicleGnss rename.
Assisted-by: Claude:claude-opus-5-5
* refactor(drivers/transponder): read sensor_gnss
Follows the SensorGps to SensorGnss and vehicle_gps_position to VehicleGnss rename.
Assisted-by: Claude:claude-opus-5-5
* refactor(boards/modalai): publish sensor_gnss from the voxl2 drivers
Follows the SensorGps to SensorGnss and vehicle_gps_position to VehicleGnss rename.
Assisted-by: Claude:claude-opus-5-5
* refactor(examples): publish sensor_gnss and read vehicle_gnss
Follows the SensorGps to SensorGnss and vehicle_gps_position to VehicleGnss rename.
Assisted-by: Claude:claude-opus-5-5
* refactor(simulation): publish sensor_gnss
Follows the SensorGps to SensorGnss and vehicle_gps_position to VehicleGnss rename.
Assisted-by: Claude:claude-opus-5-5
* refactor(gnss): name GNSS variables gnss in the sensors module and receiver drivers
GPS is one constellation. Identifiers that hold or handle GNSS samples, or bind to the renamed parameters, follow the message and parameter rename; classes, files, modules and names tied to parameters that keep GPS stay.
Assisted-by: Claude:claude-opus-5-5
* refactor(gnss): name GNSS variables gnss in the estimators and navigator
GPS is one constellation. Identifiers that hold or handle GNSS samples, or bind to the renamed parameters, follow the message and parameter rename; classes, files, modules and names tied to parameters that keep GPS stay.
Assisted-by: Claude:claude-opus-5-5
* refactor(gnss): name GNSS variables gnss in commander, mavlink and failure injection
GPS is one constellation. Identifiers that hold or handle GNSS samples, or bind to the renamed parameters, follow the message and parameter rename; classes, files, modules and names tied to parameters that keep GPS stay.
Assisted-by: Claude:claude-opus-5-5
* refactor(gnss): name GNSS variables gnss in the remaining drivers and simulation
GPS is one constellation. Identifiers that hold or handle GNSS samples, or bind to the renamed parameters, follow the message and parameter rename; classes, files, modules and names tied to parameters that keep GPS stay.
Assisted-by: Claude:claude-opus-5-5
* docs(gnss): reference sensor_gnss, vehicle_gnss and SENS_GNSS* parameters
The upgrade guide covers the topic, field, ROS 2, parameter and Cyphal register renames.
Assisted-by: Claude:claude-opus-5-5
* fix(boards): name EKF2::UpdateGnssSample in the fmu-v6xrt ITCM lists
The rename left the old UpdateGpsSample symbol in the lists, so the ITCM check fails and the function drops out of ITCM on the boards it doesn't check.
Assisted-by: Claude:claude-opus-5-5
* chore(drivers/gps): bump PX4-GPSDrivers to the merged sensor_gnss rename
The submodule pointed at the PX4-GPSDrivers#243 branch commit; #243 is merged.
Assisted-by: Claude:claude-opus-5-5
* docs(msg): restore WGS84 in SensorGnss and point VehicleGlobalPosition at vehicle_gnss
The rename dropped the only mention of the WGS84 datum and ellipsoid, and left VehicleGlobalPosition referring to the removed vehicle_gps_position topic.
Assisted-by: Claude:claude-opus-5-5
* refactor(msg): drop selected_instance from VehicleGnss
receiver.device_id already names the selected receiver, and 0 while blended. The sensor_gnss instance depends on the order drivers advertise at boot, so it doesn't identify a receiver across boots or logs, and nothing reads it. It would also be meaningless on the per-receiver VehicleGnss instances proposed in #28894.
Assisted-by: Claude:claude-opus-5-5
* refactor(gnss): fuse vehicle_gnss.timestamp_sample directly and document the receiver's corrected time
vehicle_gnss.timestamp is now the sensors module's publish time, so EKF2's check of timestamp_sample against it was always true; the sensors module always fills timestamp_sample. The message docs described receiver.timestamp_sample as the driver's uncorrected value, but the sensors module writes the corrected time into it as well.
Assisted-by: Claude:claude-opus-5-5
* docs(msg): point VehicleGnss users at the top-level timestamp_sample
uXRCE-DDS shifts only top-level timestamp and timestamp_sample into agent time, so receiver.timestamp_sample reaches ROS 2 on the PX4 boot clock even though it holds the same value on uORB.
Assisted-by: Claude:claude-opus-5-5
* docs(releases): tell ROS 2 users which VehicleGnss timestamps to read
Only top-level timestamps are converted to ROS time, so a port that reads receiver.timestamp gets the PX4 boot clock, and vehicle_gnss.timestamp is now the sensors module's publish time rather than the receiver's.
Assisted-by: Claude:claude-opus-5-5
The jMAVSim pages become redirects to SIH, examples and HITL options
move to SIH, Gazebo or Gazebo Classic, and SIH on hardware gets Hawkeye
as its 3D display-only view through a MAVLink bridge to its UDP port.
The release notes flag the removal in the upgrade guide.
Assisted-by: Claude:claude-opus-5-5
Signed-off-by: Ramon Roche <mrpollo@gmail.com>
* feat(failure-injection): implement motor failure injection with soft and hard modes
* feat(failure-injection): update motor failure injection descriptions and behaviors for annunciated and un-annunciated modes
* feat(failure-injection): update motor failure injection terminology to detected and undetected modes
* feat(failure-injection): refine motor failure injection handling for detected and undetected modes
* fix(boards): remove FailureInjector::update() from itcm_functions
FailureInjector was replaced by the shared failure_injection library, so
the symbol no longer exists and the ITCM check fails on the boards that
still list it. Its successor failure_injection::Config::update() is an
inline no-op unless MODULES_FAILURE_INJECTION_MANAGER is enabled, which
none of these boards do, so there is no replacement symbol to map.
Assisted-by: Claude:claude-opus-5
Signed-off-by: Claudio-Chies <61051109+Claudio-Chies@users.noreply.github.com>
---------
Signed-off-by: Claudio-Chies <61051109+Claudio-Chies@users.noreply.github.com>
Co-authored-by: Claudio Chies <chiesc@chies.com>
On NuttX these are two things: / is the filesystem root, and /fs/microsd is the
SD card mounted under it. MAVLink FTP serves the root and confines writes to the
SD card, so the read-only ROMFS at /etc is visible but cannot be written.
On POSIX they were the same directory. PX4_ROOTFSDIR and PX4_STORAGEDIR both
resolved to CONFIG_BOARD_ROOT_PATH, which on SITL is ".", so the working
directory was simultaneously the FTP root and the only writable area. The
consequences were that the ROMFS symlink sat inside the FTP root, and that
_validatePathIsWritable() had nothing meaningful to check against and so was
compiled out on POSIX entirely, leaving no write restriction at all.
Give POSIX the same split. CONFIG_BOARD_ROOT_PATH keeps its meaning as the
storage directory, and a new CONFIG_BOARD_FS_ROOT_PATH names the root FTP
serves, defaulting to the storage path so every existing board is unchanged.
SITL sets the root to "." and storage to "./fs", which mirrors NuttX: logs,
parameters, dataman and eeprom move under ./fs, and etc/ stays in the root as
read-only data.
With storage distinct from the root, the write restriction now applies on every
platform rather than NuttX only, and no longer compares against a hardcoded
prefix length that was wrong for any board not using /fs/microsd.
Assisted-by: Claude:claude-opus-5[1m]
Signed-off-by: Julian Oes <julian@oes.ch>
* fix(gz_bridge): support GPS failure injection
Modern Gazebo publishes sensor_gps directly from GZBridge, bypassing the shared failure-injection processing. Route each NavSat sample through process_gnss using the actual uORB publication instance so off, stuck, wrong, and recovery work for the addressed receiver.
Add functional regression coverage for the real GZBridge NavSat callback and sensor_gps publication path, plus recovery coverage for the shared GNSS processor.
Fixes#22296
Assisted-by: Codex:gpt-5
Signed-off-by: Saibernard Yogendran <bernie97@seas.upenn.edu>
* docs: gps failure injection is available on Gazebo
The gz_bridge now applies the shared GNSS failure state to the
simulator's NavSat data, so the table entry and the SIM_GZ_EN_GPS
workaround note are out of date.
Assisted-by: Claude:claude-fable-5
Signed-off-by: Saibernard Yogendran <bernie97@seas.upenn.edu>
---------
Signed-off-by: Saibernard Yogendran <bernie97@seas.upenn.edu>
* docs(ros2): reorder setup steps
- Use a standalone ROS 2 workspace for px4_msgs and
(optionally) the uXRCE-DDS Agent
- Build uXRCE-DDS Agent inside the ROS 2 workspace
- remove `px4_ros_com` package as mandatory package in the
workspace setup. Now it is just used in the examples.
Signed-off-by: Beniamino Pozzan <beniamino.pozzan@gmail.com>
* Apply suggestions from code review
Co-authored-by: Hamish Willee <hamishwillee@gmail.com>
* Apply suggestion from @hamishwillee
* docs(docs): fix up the links to broken anchors
---------
Signed-off-by: Beniamino Pozzan <beniamino.pozzan@gmail.com>
Co-authored-by: Hamish Willee <hamishwillee@gmail.com>
* feat(failure_injection): add ADS-B traffic-avoidance failure injection
Wire up FAILURE_UNIT_SYSTEM_TRAFFIC_AVOIDANCE (107) for the MAVLink-based
traffic avoidance path:
- OFF suppresses and STUCK freezes the incoming transponder_report, applied
both at the MAVLink ADS-B ingestion (handle_message_adsb_vehicle) and at
the navigator consumer (check_traffic), so it works for real ADS-B over
MAVLink, simulated ADS-B and the fake_traffic command.
- OFF additionally marks the ADS-B/FLARM heartbeat unhealthy so the traffic
avoidance system health check fails, using a message-less process()
overload.
- Add the unit to the capability catalogue (OK/OFF/STUCK), the failure
console command, the RC-switch unit selector and the docs.
The matching MAVLink FAILURE_UNIT enum entry lives in the mavlink submodule
(common.xml) and is handled by a separate PR; the uORB mirrors in
VehicleCommand.msg and FailureInjection.msg are included here.
* feat(failure_injection): enhance battery failure injection with severity levels
* feat(failure_injection): improve battery failure handling with dynamic threshold parameters
* refactor(failure_injection): remove traffic avoidance example from documentation
* docs(docs): subedit
* feat(failure_injection): add variance setting for distance sensor and integrate rangefinder in simulator
* feat(docs): add failure injection to release notes
* docs(docs): Add sim_mavlink back to heading
* fix(failure_injection): update default battery failure injection severity to Emergency
* docs(docs): get away from footnotes
* feat(failure_injection): enhance battery failure injection handling and update traffic unit support
* feat(failure_injection): add traffic avoidance handling tests and configurations
* [AUTO COMMIT] update EKF change indication
See .github/workflows/checks.yml for more details
* Apply suggestion from @hamishwillee
* feat(failure_injection): update failure types and handling for traffic avoidance and ESC telemetry
* fix(typo)
* [AUTO COMMIT] update EKF change indication
See .github/workflows/checks.yml for more details
* fix(docs): clarify notes on GPS and airspeed handling in failure injection documentation
---------
Co-authored-by: Claudio Chies <chiesc@chies.com>
Co-authored-by: Hamish Willee <hamishwillee@gmail.com>
* feat(failure_injection): integrate failure injection support across sensor drivers
* feat(failure_injection): enhance failure injection with RC switch support and instance bitmasking
feat(failure_injection): add disabled failure injection manager and system command support for v5x and v6x boards
* feat(failure_injection): add battery failure injection
Add a value-mutating apply-site for FAILURE_UNIT_SYSTEM_BATTERY. On an
injected OFF the outgoing battery_status is reported as a depleted pack
(zero remaining, emergency warning) so the low-battery failsafe triggers.
The apply-site lives in the shared Battery library, covering the analog
ADC, INA power monitors, ESC battery and SITL in one place, plus the
UAVCAN battery driver which publishes battery_status directly. The
previous SITL-only hack in BatterySimulator is removed in favour of this
shared path so simulation and hardware behave identically.
* fix(failure_injection): change parameter types from int32 to enum
* refactor(failure_injection): disable failure injection manager and system commands across multiple boards
* feat(failure_injection): enhance failure injection with timestamp handling and message-less support
* refactor(failure_injection): simplify has_timestamp_sample implementation and remove unused includes
* refactor(failure_injection):move conditional compilation into helper libary
* refactor(failure_injection): update CMakeLists to include failure_injection dependency across multiple drivers
---------
Co-authored-by: Claudio Chies <chiesc@chies.com>
* docs(docs): Add missing uorb topics sidebar
* docs(docs): discontinue cuav v5 plus/nano
* docs(docs): Fix 404 and 303 status HTTP links
* docs(docs): more link fixes
* update(drivers): Docs fix to fix up link
* docs(docs): Fix up all remaining broken links and add exclusions
* failure_injection: improve previously vague motor faulure
Reading it again I decided adding the sentance in 4d2170c13e is not clear enough.
* docs/safety: add a motor failure detection paragraph
The functionality is in my eyes pretty basic but so far completely undocumented so I went through the code and added a paragraph based on questions I received.
* Subedit
* Apply suggestion from @hamishwillee
---------
Co-authored-by: Hamish Willee <hamishwillee@gmail.com>
* Add vitepress tree
* Update existing workflows so they dont trigger on changes in the docs path
* Add nojekyll, package.json, LICENCE etc
* Add crowdin docs upload/download scripts
* Add docs flaw checker workflows
* Used docs prefix for docs workflows
* Crowdin obvious fixes
* ci: docs move to self hosted runner
runs on a beefy server for faster builds
Signed-off-by: Ramon Roche <mrpollo@gmail.com>
* ci: don't run build action for docs or ci changes
Signed-off-by: Ramon Roche <mrpollo@gmail.com>
* ci: update runners
Signed-off-by: Ramon Roche <mrpollo@gmail.com>
* Add docs/en
* Add docs assets and scripts
* Fix up editlinks to point to PX4 sources
* Download just the translations that are supported
* Add translation sources for zh, uk, ko
* Update latest tranlsation and uorb graphs
* update vitepress to latest
---------
Signed-off-by: Ramon Roche <mrpollo@gmail.com>
Co-authored-by: Ramon Roche <mrpollo@gmail.com>