24 Commits
Author SHA1 Message Date
Matthias Grob 96075cb00c fix(mag_bias_estimator): disable the mag bias estimator by default (#29342)
* fix(mag_bias_estimator): disable the mag bias estimator by default

It only helps if you have a very bad or no calibration in the first place or if the vehicle has magnets everywhere.
But it causes problems if you have a perfectly fresh calibration and no new disturbance
especially of course if the estimator runs twice, once on the can node, once on the autopilot.

* fix(mag_bias_estimator): remove the mag bias estimator from all cannodes

It will cause issues if the can nodes run their own online calibration and the autopilot expects to receive raw data. It's not super obvious but will lead to inaccuracies, drifts and inconsitencies in magnetometer heading.
2026-11-18 14:43:26 +01:00
Jacob Dahl 12b158889b chore(boards/ark/cannode): drop optical flow (#28984)
* chore(boards/ark/cannode): drop optical flow

The ARK CAN node has no flow sensor.

Assisted-by: Claude:claude-opus-5-5
Signed-off-by: Jacob Dahl <dahl.jakejacob@gmail.com>

* chore(boards/ark/cannode): keep the default optical flow sensors option

Removing the flow drivers is enough; the board config does not need to override the sensors module default.

Assisted-by: Claude:claude-opus-5-5
Signed-off-by: Jacob Dahl <dahl.jakejacob@gmail.com>

* chore(cannode): remove the px4flow start from the node startup script

No CAN node board builds the px4flow driver once the ARK CAN node drops optical flow.

Assisted-by: Claude:claude-opus-5-5
Signed-off-by: Jacob Dahl <dahl.jakejacob@gmail.com>

* chore(boards/ark/cannode): disable vehicle optical flow

The sensors module builds VehicleOpticalFlow by default, which this board never starts without a flow sensor.

Assisted-by: Claude:claude-opus-5-5
Signed-off-by: Jacob Dahl <dahl.jakejacob@gmail.com>

---------

Signed-off-by: Jacob Dahl <dahl.jakejacob@gmail.com>
2026-10-02 17:24:23 -06:00
Jacob Dahl 940af26b4b fix(sensors): disable SENS_MAG_AUTOCAL by default, keep for CAN nodes (#27659)
PR #18421 added the initial mag calibration save and was deliberately merged with SENS_MAG_AUTOCAL=0 until parameter system concerns were addressed. PR #19818 (CAN GPS nodes) flipped the global default to 1 as an undiscussed side change, shipped in v1.14.0. Since then every uncalibrated mag marks itself calibrated (CAL_MAGn_ID set) shortly after the disarmed bias estimator stabilizes, so ground stations stop prompting for compass calibration on new setups, and the first flight happens on a hard-iron-only estimate with an assumed mount rotation.

Restore the disabled default and enable it where it is genuinely needed: CAN nodes, which have no GCS calibration flow and no EKF for in-flight refinement. MBE_ENABLE is untouched, the bias estimator still runs and corrects everywhere.

Signed-off-by: Jacob Dahl <dahl.jakejacob@gmail.com>
2026-06-12 19:17:53 -06:00
Alexander Lerach 138427b3a8 config: add dynamic init file
* config: add dynamic init file

* added review feedback

* added docs
2025-08-21 16:46:06 +02:00
Peter van der Perk 46e43ec725 Decouple filepaths from rcS/MTD 2024-07-24 11:39:44 -04:00
Peter van der Perk 45244e610f NXP MR-CANHUBK3 Support 2022-12-06 06:49:28 -05:00
alexklimaj 4cc3e78558 Add mag bias estimator to CAN GPS units with IMUs
- run `sensors` hub to process sensor_mag and publish vehicle_magnetometer
 - update uavcannode to use vehicle_magnetometer
2022-06-19 15:46:36 -04:00
Daniel Agar 10deb7019e enable gyro_calibration for CAN nodes
- allow saving initial gyro cal if very close to 0
2022-06-17 19:31:45 -04:00
Daniel Agar 9073f3ccdf px4flow allow delayed background startup 2022-04-22 21:11:02 -04:00
Daniel Agar 6d78054f50 mavlink USB auto start/stop on boards with VBUS
- no longer start sercon or mavlink usb by default
 - on USB connection (VBUS) monitor serial USB at low rate and start Mavlink if there's a HEARTBEAT or nshterm on 3 consecutive carriage returns
 - the mavlink USB instance is automatically stopped and serdis executed if USB is disconnected
 - skipping Mavlink USB (and sercon) saves a considerable amount of memory on older boards
2021-10-03 15:32:54 -04:00
Daniel Agar 000765e9f0 NuttX mount procfs and binfs in px4 init 2021-09-08 10:21:24 -04:00
Daniel Agar 3d667b1675 delete unused drivers/lights/blinkm 2021-03-28 19:21:29 -04:00
Daniel Agar 631d1647d3 boards: minimize unnecessary differences in default variants 2021-03-28 14:46:47 -04:00
Daniel Agar 4d288512b5 add board architecture specific init defaults 2021-03-09 19:59:41 +01:00
David Sidrane dd3c3098f2 nxp_ucans32k146:Add Can Bootloader build
nxp_ucans32k146:Relocation for Bootloader

nxp_ucans32k146:can_boot enable CAN

nxp_ucans32k146:Save Space use Non Optimize memcpy

nxp_ucans32k146:Increase to 24K

nxp/ucans32k146:Canbootloader LED Driver

nxp_ucans32k146:Can bootloader shut down CAN

nxp_ucans32k146:Use NVMEEPROM for Paramaters

nxp_ucans32k146:Use bootloader AppDescriptor

px4 mtd:Support onchip emulated eeprom
2021-02-24 19:20:15 +01:00
Daniel Agar ab0d0fd0be uORB move to PX4 platform layer 2021-02-17 11:25:56 -05:00
Daniel Agar 9767a73619 ROMFS: silently compare optional parameters
- not all build configurations have these parameters/modules
2020-11-11 08:03:48 +01:00
David Sidrane b9319b3843 ROMFS:Use . for (source) and ${R} for pathing
init.d-posix:rcS Quiet Shell check warning
2020-10-15 17:11:08 -04:00
David Sidrane 185ffe9e13 nsh scripting:source (.) cmd supported 2020-09-16 21:32:04 -04:00
Matthias Grob ce9954a919 param: enable reseting specific parameters from shell
Renaming previous "param reset" to "param reset_all".
2020-09-08 12:03:41 +02:00
Beat KüngandDaniel Agar 4088c2581f i2c_spi_buses: add '-q' for quiet startup flag (#14969)
* [WIP] i2c_spi_buses: add '-q' for quiet startup flag

And enable for optional board sensors.

* ROMFS: rc.sensors try starting all optional I2C sensors quietly

Co-authored-by: Daniel Agar <daniel@agar.ca>
2020-08-26 08:46:35 +02:00
Beat Küng 1710cd9648 refactor px4flow: use driver base class 2020-03-17 23:31:17 -04:00
Beat Küng ec2de33547 lights: use driver base class 2020-03-17 23:31:17 -04:00
Daniel Agar d7c3e1066a uavcannode updates and px4_fmu-v4_cannode example
- drivers/uavcannode add baro, mag, gps publications
 - delete old px4_cannode-v1 board
 - add stripped down simple rcS for CAN nodes
2020-02-16 12:11:54 -05:00