mirror of
https://github.com/PX4/PX4-Autopilot.git
synced 2026-11-22 14:19:57 +08:00
docs: auto-sync metadata [skip ci]
Co-Authored-By: PX4 BuildBot <bot@px4.io>
This commit is contained in:
1 parent
357fe278ab
commit
89cfa5bbbd
6 files changed
+50
-40
No files matched your search
@@ -31138,7 +31138,10 @@ Reboot | minValue | maxValue | increment | default | unit | Read-Only
|
||||
|
||||
Maximum manual pitch angle.
|
||||
|
||||
Applies to both directions in all manual modes with attitude stabilization but without altitude control
|
||||
Pitch angle commanded by full stick deflection, relative to FW_PSP_OFF (the centred-stick pitch).
|
||||
The resulting pitch setpoint is additionally limited to this angle around level,
|
||||
so with a non-zero FW_PSP_OFF the range is not symmetric.
|
||||
Applies in all manual modes with attitude stabilization but without altitude control.
|
||||
|
||||
|
||||
Reboot | minValue | maxValue | increment | default | unit | Read-Only
|
||||
@@ -31184,9 +31187,12 @@ Reboot | minValue | maxValue | increment | default | unit | Read-Only
|
||||
|
||||
Pitch setpoint offset (pitch at level flight).
|
||||
|
||||
An airframe specific offset of the pitch setpoint in degrees, the value is
|
||||
added to the pitch setpoint and should correspond to the pitch at
|
||||
typical cruise speed of the airframe.
|
||||
Pitch angle of the body x-axis above the horizon in level flight at trim airspeed (FW_AIRSPD_TRIM).
|
||||
|
||||
The altitude and airspeed controller (TECS) uses it as the pitch at zero climb angle,
|
||||
and in Stabilized mode the centred pitch stick commands it.
|
||||
Pitch setpoints and pitch limits set elsewhere, for example FW_P_LIM_MIN and FW_P_LIM_MAX,
|
||||
are absolute and do not include it.
|
||||
|
||||
|
||||
Reboot | minValue | maxValue | increment | default | unit | Read-Only
|
||||
@@ -31493,7 +31499,7 @@ Reboot | minValue | maxValue | increment | default | unit | Read-Only
|
||||
|
||||
### FW_LND_FL_PMAX (`FLOAT`) {#FW_LND_FL_PMAX}
|
||||
|
||||
Flare, maximum pitch.
|
||||
Flare, maximum absolute pitch.
|
||||
|
||||
Maximum pitch during landing flare.
|
||||
|
||||
@@ -31508,7 +31514,7 @@ Reboot | minValue | maxValue | increment | default | unit | Read-Only
|
||||
|
||||
### FW_LND_FL_PMIN (`FLOAT`) {#FW_LND_FL_PMIN}
|
||||
|
||||
Flare, minimum pitch.
|
||||
Flare, minimum absolute pitch.
|
||||
|
||||
Minimum pitch during landing flare.
|
||||
|
||||
@@ -31893,7 +31899,7 @@ Reboot | minValue | maxValue | increment | default | unit | Read-Only
|
||||
|
||||
### FW_TKO_PITCH_MIN (`FLOAT`) {#FW_TKO_PITCH_MIN}
|
||||
|
||||
Minimum pitch during takeoff.
|
||||
Minimum absolute pitch during takeoff.
|
||||
|
||||
Reboot | minValue | maxValue | increment | default | unit | Read-Only
|
||||
--- | --- | --- | --- | --- | --- | ---
|
||||
@@ -31964,7 +31970,7 @@ Reboot | minValue | maxValue | increment | default | unit | Read-Only
|
||||
|
||||
### FW_P_LIM_MAX (`FLOAT`) {#FW_P_LIM_MAX}
|
||||
|
||||
Maximum pitch angle setpoint.
|
||||
Maximum absolute pitch angle setpoint.
|
||||
|
||||
Applies in any altitude controlled flight mode.
|
||||
|
||||
@@ -31979,7 +31985,7 @@ Reboot | minValue | maxValue | increment | default | unit | Read-Only
|
||||
|
||||
### FW_P_LIM_MIN (`FLOAT`) {#FW_P_LIM_MIN}
|
||||
|
||||
Minimum pitch angle setpoint.
|
||||
Minimum absolute pitch angle setpoint.
|
||||
|
||||
Applies in any altitude controlled flight mode.
|
||||
|
||||
@@ -48802,7 +48808,7 @@ Reboot | minValue | maxValue | increment | default | unit | Read-Only
|
||||
|
||||
### RWTO_PSP (`FLOAT`) {#RWTO_PSP}
|
||||
|
||||
Pitch setpoint during taxi / before rotation.
|
||||
Absolute pitch setpoint during taxi / before rotation.
|
||||
|
||||
Pitch setpoint during taxi / before takeoff rotation airspeed is reached
|
||||
|
||||
|
||||
@@ -24,7 +24,7 @@ Used by controllers, estimators and for airspeed reporting to operator.
|
||||
| <a id="fld_calibraded_airspeed_synth_m_s"></a>calibraded_airspeed_synth_m_s | `float32` | m/s | | Synthetic airspeed (Invalid: NaN) |
|
||||
| <a id="fld_airspeed_derivative_filtered"></a>airspeed_derivative_filtered | `float32` | m/s^2 | | Filtered indicated airspeed derivative |
|
||||
| <a id="fld_throttle_filtered"></a>throttle_filtered | `float32` | | | Filtered fixed-wing throttle |
|
||||
| <a id="fld_pitch_filtered"></a>pitch_filtered | `float32` | rad | | Filtered pitch |
|
||||
| <a id="fld_pitch_filtered"></a>pitch_filtered | `float32` | rad | | Filtered absolute pitch angle of the fixed-wing body x-axis above the horizon |
|
||||
|
||||
## Enums
|
||||
|
||||
@@ -79,7 +79,7 @@ float32 calibrated_ground_minus_wind_m_s # [m/s] [@invalid NaN] CAS calculated f
|
||||
float32 calibraded_airspeed_synth_m_s # [m/s] [@invalid NaN] Synthetic airspeed
|
||||
float32 airspeed_derivative_filtered # [m/s^2] Filtered indicated airspeed derivative
|
||||
float32 throttle_filtered # [-] Filtered fixed-wing throttle
|
||||
float32 pitch_filtered # [rad] Filtered pitch
|
||||
float32 pitch_filtered # [rad] Filtered absolute pitch angle of the fixed-wing body x-axis above the horizon
|
||||
```
|
||||
|
||||
:::
|
||||
@@ -9,19 +9,20 @@ Fixed Wing Longitudinal Setpoint message.
|
||||
Used by the fw_lateral_longitudinal_control module
|
||||
If pitch_direct and throttle_direct are not both finite, then the controller relies on altitude/height_rate and equivalent_airspeed to control vertical motion.
|
||||
If both altitude and height_rate are NAN, the controller maintains the current altitude.
|
||||
Pitch angles are absolute: the angle of the fixed-wing body x-axis above the horizon, without FW_PSP_OFF applied.
|
||||
|
||||
**TOPICS:** fixed_wing_longitudinal_setpoint
|
||||
|
||||
## Fields
|
||||
|
||||
| Name | Type | Unit [Frame] | Range/Enum | Description |
|
||||
| ------------------------------------------------------- | --------- | ------------ | ---------- | ---------------------------------------------------------------------------------- |
|
||||
| <a id="fld_timestamp"></a>timestamp | `uint64` | us | | Time since system start |
|
||||
| <a id="fld_altitude"></a>altitude | `float32` | m | | Altitude setpoint AMSL, not controlled directly if NAN or if height_rate is finite |
|
||||
| <a id="fld_height_rate"></a>height_rate | `float32` | m/s [ENU] | | Scalar height rate setpoint. NAN if not controlled directly |
|
||||
| <a id="fld_equivalent_airspeed"></a>equivalent_airspeed | `float32` | m/s | [0 : inf] | Scalar equivalent airspeed setpoint. NAN if system default should be used |
|
||||
| <a id="fld_pitch_direct"></a>pitch_direct | `float32` | rad [FRD] | [-pi : pi] | NAN if not controlled, overrides total energy controller |
|
||||
| <a id="fld_throttle_direct"></a>throttle_direct | `float32` | norm | [0 : 1] | NAN if not controlled, overrides total energy controller |
|
||||
| Name | Type | Unit [Frame] | Range/Enum | Description |
|
||||
| ------------------------------------------------------- | --------- | ------------ | -------------- | --------------------------------------------------------------------------------------- |
|
||||
| <a id="fld_timestamp"></a>timestamp | `uint64` | us | | Time since system start |
|
||||
| <a id="fld_altitude"></a>altitude | `float32` | m | | Altitude setpoint AMSL, not controlled directly if NAN or if height_rate is finite |
|
||||
| <a id="fld_height_rate"></a>height_rate | `float32` | m/s [ENU] | | Scalar height rate setpoint. NAN if not controlled directly |
|
||||
| <a id="fld_equivalent_airspeed"></a>equivalent_airspeed | `float32` | m/s | [0 : inf] | Scalar equivalent airspeed setpoint. NAN if system default should be used |
|
||||
| <a id="fld_pitch_direct"></a>pitch_direct | `float32` | rad | [-pi/2 : pi/2] | Absolute pitch angle setpoint. NAN if not controlled, overrides total energy controller |
|
||||
| <a id="fld_throttle_direct"></a>throttle_direct | `float32` | norm | [0 : 1] | NAN if not controlled, overrides total energy controller |
|
||||
|
||||
## Constants
|
||||
|
||||
@@ -41,6 +42,7 @@ If both altitude and height_rate are NAN, the controller maintains the current a
|
||||
# Used by the fw_lateral_longitudinal_control module
|
||||
# If pitch_direct and throttle_direct are not both finite, then the controller relies on altitude/height_rate and equivalent_airspeed to control vertical motion.
|
||||
# If both altitude and height_rate are NAN, the controller maintains the current altitude.
|
||||
# Pitch angles are absolute: the angle of the fixed-wing body x-axis above the horizon, without FW_PSP_OFF applied.
|
||||
|
||||
uint32 MESSAGE_VERSION = 0
|
||||
|
||||
@@ -49,7 +51,7 @@ uint64 timestamp # [us] Time since system start
|
||||
float32 altitude # [m] Altitude setpoint AMSL, not controlled directly if NAN or if height_rate is finite
|
||||
float32 height_rate # [m/s] [@frame ENU] Scalar height rate setpoint. NAN if not controlled directly
|
||||
float32 equivalent_airspeed # [m/s] [@range 0, inf] Scalar equivalent airspeed setpoint. NAN if system default should be used
|
||||
float32 pitch_direct # [rad] [@range -pi, pi] [@frame FRD] NAN if not controlled, overrides total energy controller
|
||||
float32 pitch_direct # [rad] [@range -pi/2, pi/2] Absolute pitch angle setpoint. NAN if not controlled, overrides total energy controller
|
||||
float32 throttle_direct # [norm] [@range 0,1] NAN if not controlled, overrides total energy controller
|
||||
```
|
||||
|
||||
|
||||
@@ -8,23 +8,24 @@ Fixed Wing Longitudinal Control Configuration message.
|
||||
|
||||
Used by the fw_lateral_longitudinal_control module and TECS to constrain FixedWingLongitudinalSetpoint messages
|
||||
and configure the resultant setpoints.
|
||||
Pitch angles are absolute: the angle of the fixed-wing body x-axis above the horizon, without FW_PSP_OFF applied.
|
||||
|
||||
**TOPICS:** longitudinal_control_configuration
|
||||
|
||||
## Fields
|
||||
|
||||
| Name | Type | Unit [Frame] | Range/Enum | Description |
|
||||
| --------------------------------------------------------------------------- | --------- | ------------ | ---------- | ------------------------------------------------------------------------------------------------------------------------------------------------- |
|
||||
| <a id="fld_timestamp"></a>timestamp | `uint64` | us | | Time since system start |
|
||||
| <a id="fld_pitch_min"></a>pitch_min | `float32` | rad | [-pi : pi] | Defaults to FW_P_LIM_MIN if NAN. |
|
||||
| <a id="fld_pitch_max"></a>pitch_max | `float32` | rad | [-pi : pi] | Defaults to FW_P_LIM_MAX if NAN. |
|
||||
| <a id="fld_throttle_min"></a>throttle_min | `float32` | norm | [0 : 1] | Defaults to FW_THR_MIN if NAN. |
|
||||
| <a id="fld_throttle_max"></a>throttle_max | `float32` | norm | [0 : 1] | Defaults to FW_THR_MAX if NAN. |
|
||||
| <a id="fld_climb_rate_target"></a>climb_rate_target | `float32` | m/s | | Target climbrate to change altitude. Defaults to FW_T_CLMB_R_SP if NAN. Not used if height_rate is directly set in FixedWingLongitudinalSetpoint. |
|
||||
| <a id="fld_sink_rate_target"></a>sink_rate_target | `float32` | m/s | | Target sinkrate to change altitude. Defaults to FW_T_SINK_R_SP if NAN. Not used if height_rate is directly set in FixedWingLongitudinalSetpoint. |
|
||||
| <a id="fld_speed_weight"></a>speed_weight | `float32` | | [0 : 2] | 0=pitch controls altitude only, 2=pitch controls airspeed only |
|
||||
| <a id="fld_enforce_low_height_condition"></a>enforce_low_height_condition | `bool` | | | If true, the altitude controller is configured with an alternative timeconstant for tighter altitude tracking |
|
||||
| <a id="fld_disable_underspeed_protection"></a>disable_underspeed_protection | `bool` | | | If true, underspeed handling is disabled in the altitude controller |
|
||||
| Name | Type | Unit [Frame] | Range/Enum | Description |
|
||||
| --------------------------------------------------------------------------- | --------- | ------------ | -------------- | ------------------------------------------------------------------------------------------------------------------------------------------------- |
|
||||
| <a id="fld_timestamp"></a>timestamp | `uint64` | us | | Time since system start |
|
||||
| <a id="fld_pitch_min"></a>pitch_min | `float32` | rad | [-pi/2 : pi/2] | Minimum absolute pitch angle setpoint. Defaults to FW_P_LIM_MIN if NAN. |
|
||||
| <a id="fld_pitch_max"></a>pitch_max | `float32` | rad | [-pi/2 : pi/2] | Maximum absolute pitch angle setpoint. Defaults to FW_P_LIM_MAX if NAN. |
|
||||
| <a id="fld_throttle_min"></a>throttle_min | `float32` | norm | [0 : 1] | Defaults to FW_THR_MIN if NAN. |
|
||||
| <a id="fld_throttle_max"></a>throttle_max | `float32` | norm | [0 : 1] | Defaults to FW_THR_MAX if NAN. |
|
||||
| <a id="fld_climb_rate_target"></a>climb_rate_target | `float32` | m/s | | Target climbrate to change altitude. Defaults to FW_T_CLMB_R_SP if NAN. Not used if height_rate is directly set in FixedWingLongitudinalSetpoint. |
|
||||
| <a id="fld_sink_rate_target"></a>sink_rate_target | `float32` | m/s | | Target sinkrate to change altitude. Defaults to FW_T_SINK_R_SP if NAN. Not used if height_rate is directly set in FixedWingLongitudinalSetpoint. |
|
||||
| <a id="fld_speed_weight"></a>speed_weight | `float32` | | [0 : 2] | 0=pitch controls altitude only, 2=pitch controls airspeed only |
|
||||
| <a id="fld_enforce_low_height_condition"></a>enforce_low_height_condition | `bool` | | | If true, the altitude controller is configured with an alternative timeconstant for tighter altitude tracking |
|
||||
| <a id="fld_disable_underspeed_protection"></a>disable_underspeed_protection | `bool` | | | If true, underspeed handling is disabled in the altitude controller |
|
||||
|
||||
## Constants
|
||||
|
||||
@@ -43,13 +44,14 @@ and configure the resultant setpoints.
|
||||
#
|
||||
# Used by the fw_lateral_longitudinal_control module and TECS to constrain FixedWingLongitudinalSetpoint messages
|
||||
# and configure the resultant setpoints.
|
||||
# Pitch angles are absolute: the angle of the fixed-wing body x-axis above the horizon, without FW_PSP_OFF applied.
|
||||
|
||||
uint32 MESSAGE_VERSION = 0
|
||||
|
||||
uint64 timestamp # [us] Time since system start
|
||||
|
||||
float32 pitch_min # [rad] [@range -pi, pi] Defaults to FW_P_LIM_MIN if NAN.
|
||||
float32 pitch_max # [rad] [@range -pi, pi] Defaults to FW_P_LIM_MAX if NAN.
|
||||
float32 pitch_min # [rad] [@range -pi/2, pi/2] Minimum absolute pitch angle setpoint. Defaults to FW_P_LIM_MIN if NAN.
|
||||
float32 pitch_max # [rad] [@range -pi/2, pi/2] Maximum absolute pitch angle setpoint. Defaults to FW_P_LIM_MAX if NAN.
|
||||
float32 throttle_min # [norm] [@range 0,1] Defaults to FW_THR_MIN if NAN.
|
||||
float32 throttle_max # [norm] [@range 0,1] Defaults to FW_THR_MAX if NAN.
|
||||
float32 climb_rate_target # [m/s] Target climbrate to change altitude. Defaults to FW_T_CLMB_R_SP if NAN. Not used if height_rate is directly set in FixedWingLongitudinalSetpoint.
|
||||
|
||||
@@ -29,9 +29,9 @@ pageClass: is-wide-page
|
||||
| <a id="fld_total_energy_balance_rate_sp"></a>total_energy_balance_rate_sp | `float32` | | | Energy balance rate setpoint [m^2/s^3] |
|
||||
| <a id="fld_total_energy_balance_rate"></a>total_energy_balance_rate | `float32` | | | Energy balance rate estimate [m^2/s^3] |
|
||||
| <a id="fld_throttle_integ"></a>throttle_integ | `float32` | | | Throttle integrator value [-] |
|
||||
| <a id="fld_pitch_integ"></a>pitch_integ | `float32` | | | Pitch integrator value [rad] |
|
||||
| <a id="fld_pitch_integ"></a>pitch_integ | `float32` | | | Pitch integrator value [rad], a correction added to the pitch setpoint rather than a pitch angle |
|
||||
| <a id="fld_throttle_sp"></a>throttle_sp | `float32` | | | Current throttle setpoint [-] |
|
||||
| <a id="fld_pitch_sp_rad"></a>pitch_sp_rad | `float32` | | | Current pitch setpoint [rad] |
|
||||
| <a id="fld_pitch_sp_rad"></a>pitch_sp_rad | `float32` | | | Current pitch setpoint [rad], absolute: angle of the fixed-wing body x-axis above the horizon, FW_PSP_OFF included |
|
||||
| <a id="fld_throttle_trim"></a>throttle_trim | `float32` | | | estimated throttle value [0,1] required to fly level at equivalent_airspeed_sp in the current atmospheric conditions |
|
||||
| <a id="fld_underspeed_ratio"></a>underspeed_ratio | `float32` | | | 0: no underspeed, 1: maximal underspeed. Controller takes measures to avoid stall proportional to ratio if >0. |
|
||||
| <a id="fld_fast_descend_ratio"></a>fast_descend_ratio | `float32` | | | value indicating if fast descend mode is enabled with ramp up and ramp down [0-1] |
|
||||
@@ -67,10 +67,10 @@ float32 total_energy_balance_rate_sp # Energy balance rate setpoint [m^2/s^3]
|
||||
float32 total_energy_balance_rate # Energy balance rate estimate [m^2/s^3]
|
||||
|
||||
float32 throttle_integ # Throttle integrator value [-]
|
||||
float32 pitch_integ # Pitch integrator value [rad]
|
||||
float32 pitch_integ # Pitch integrator value [rad], a correction added to the pitch setpoint rather than a pitch angle
|
||||
|
||||
float32 throttle_sp # Current throttle setpoint [-]
|
||||
float32 pitch_sp_rad # Current pitch setpoint [rad]
|
||||
float32 pitch_sp_rad # Current pitch setpoint [rad], absolute: angle of the fixed-wing body x-axis above the horizon, FW_PSP_OFF included
|
||||
float32 throttle_trim # estimated throttle value [0,1] required to fly level at equivalent_airspeed_sp in the current atmospheric conditions
|
||||
|
||||
float32 underspeed_ratio # 0: no underspeed, 1: maximal underspeed. Controller takes measures to avoid stall proportional to ratio if >0.
|
||||
|
||||
@@ -1 +1 @@
|
||||
{"parameters": [{"category": "Standard", "default": 0, "group": "ADSB", "longDesc": "Sets first 4 characters of a total of 8. Valid characters are A-Z, 0-9, \" \". Example \"PX4 \" -> 1347957792\nFor CALLSIGN shorter than 8 characters use the null terminator at the end '\\0'.\n", "name": "ADSB_CALLSIGN_1", "rebootRequired": true, "shortDesc": "First 4 characters of CALLSIGN", "type": "Int32"}, {"category": "Standard", "default": 0, "group": "ADSB", "longDesc": "Sets second 4 characters of a total of 8. Valid characters are A-Z, 0-9, \" \" only. Example \"TEST\" -> 1413829460\nFor CALLSIGN shorter than 8 characters use the null terminator at the end '\\0'.\n", "name": "ADSB_CALLSIGN_2", "rebootRequired": true, "shortDesc": "Second 4 characters of CALLSIGN", "type": "Int32"}, {"category": "Standard", "default": 0, "group": "ADSB", "longDesc": "Sets the vehicle emergency state\n", "max": 6, "min": 0, "name": "ADSB_EMERGC", "rebootRequired": true, "shortDesc": "ADSB-Out Emergency State", "type": "Int32", "values": [{"description": "NoEmergency", "value": 0}, {"description": "General", "value": 1}, {"description": "Medical", "value": 2}, {"description": "LowFuel", "value": 3}, {"description": "NoCommunications", "value": 4}, {"description": "Interference", "value": 5}, {"description": "Downed", "value": 6}]}, {"category": "Standard", "default": 14, "group": "ADSB", "longDesc": "Configure the emitter type of the vehicle.\n", "max": 19, "min": 0, "name": "ADSB_EMIT_TYPE", "rebootRequired": true, "shortDesc": "ADSB-Out Vehicle Emitter Type", "type": "Int32", "values": [{"description": "Unknown", "value": 0}, {"description": "Light", "value": 1}, {"description": "Small", "value": 2}, {"description": "Large", "value": 3}, {"description": "HighVortex", "value": 4}, {"description": "Heavy", "value": 5}, {"description": "Performance", "value": 6}, {"description": "Rotorcraft", "value": 7}, {"description": "RESERVED", "value": 8}, {"description": "Glider", "value": 9}, {"description": "LightAir", "value": 10}, {"description": "Parachute", "value": 11}, {"description": "UltraLight", "value": 12}, {"description": "RESERVED", "value": 13}, {"description": "UAV", "value": 14}, {"description": "Space", "value": 15}, {"description": "RESERVED", "value": 16}, {"description": "EmergencySurf", "value": 17}, {"description": "ServiceSurf", "value": 18}, {"description": "PointObstacle", "value": 19}]}, {"category": "Standard", "default": 0, "group": "ADSB", "longDesc": "Sets GPS lataral offset encoding\n", "max": 7, "min": 0, "name": "ADSB_GPS_OFF_LAT", "rebootRequired": true, "shortDesc": "ADSB-Out GPS Offset lat", "type": "Int32", "values": [{"description": "NoData", "value": 0}, {"description": "LatLeft2M", "value": 1}, {"description": "LatLeft4M", "value": 2}, {"description": "LatLeft6M", "value": 3}, {"description": "LatRight0M", "value": 4}, {"description": "LatRight2M", "value": 5}, {"description": "LatRight4M", "value": 6}, {"description": "LatRight6M", "value": 7}]}, {"category": "Standard", "default": 0, "group": "ADSB", "longDesc": "Sets GPS longitudinal offset encoding\n", "max": 1, "min": 0, "name": "ADSB_GPS_OFF_LON", "rebootRequired": true, "shortDesc": "ADSB-Out GPS Offset lon", "type": "Int32", "values": [{"description": "NoData", "value": 0}, {"description": "AppliedBySensor", "value": 1}]}, {"category": "Standard", "default": -1, "group": "ADSB", "longDesc": "Vehicle ICAO ID. Use -1 to disable.\n", "max": 16777215, "min": -1, "name": "ADSB_ICAO_ID", "rebootRequired": true, "shortDesc": "ADSB-Out ICAO ID", "type": "Int32"}, {"category": "Standard", "default": -1, "group": "ADSB", "longDesc": "Optional second ownship ICAO ID used to filter self-detections. Use -1 to disable.\n", "max": 16777215, "min": -1, "name": "ADSB_ICAO_ID_2", "rebootRequired": true, "shortDesc": "Secondary ownship ICAO ID", "type": "Int32"}, {"category": "Standard", "default": 0, "group": "ADSB", "longDesc": "This vehicle is always tracked. Use 0 to disable.\n", "max": 16777215, "min": 0, "name": "ADSB_ICAO_SPECL", "rebootRequired": true, "shortDesc": "ADSB-In Special ICAO configuration", "type": "Int32"}, {"category": "Standard", "default": 0, "group": "ADSB", "longDesc": "Enable Identification of Position feature\n", "name": "ADSB_IDENT", "rebootRequired": true, "shortDesc": "ADSB-Out Ident Configuration", "type": "Int32", "values": [{"description": "Disabled", "value": 0}, {"description": "Enabled", "value": 1}]}, {"category": "Standard", "default": 1, "group": "ADSB", "longDesc": "Report the length and width of the vehicle in meters. In most cases, use '1' for the smallest vehicle size.\n", "max": 15, "min": 0, "name": "ADSB_LEN_WIDTH", "rebootRequired": true, "shortDesc": "ADSB-Out Vehicle Size Configuration", "type": "Int32", "values": [{"description": "SizeUnknown", "value": 0}, {"description": "Len15_Wid23", "value": 1}, {"description": "Len25_Wid28", "value": 2}, {"description": "Len25_Wid34", "value": 3}, {"description": "Len35_Wid3Line truncated
|
||||
{"parameters": [{"category": "Standard", "default": 0, "group": "ADSB", "longDesc": "Sets first 4 characters of a total of 8. Valid characters are A-Z, 0-9, \" \". Example \"PX4 \" -> 1347957792\nFor CALLSIGN shorter than 8 characters use the null terminator at the end '\\0'.\n", "name": "ADSB_CALLSIGN_1", "rebootRequired": true, "shortDesc": "First 4 characters of CALLSIGN", "type": "Int32"}, {"category": "Standard", "default": 0, "group": "ADSB", "longDesc": "Sets second 4 characters of a total of 8. Valid characters are A-Z, 0-9, \" \" only. Example \"TEST\" -> 1413829460\nFor CALLSIGN shorter than 8 characters use the null terminator at the end '\\0'.\n", "name": "ADSB_CALLSIGN_2", "rebootRequired": true, "shortDesc": "Second 4 characters of CALLSIGN", "type": "Int32"}, {"category": "Standard", "default": 0, "group": "ADSB", "longDesc": "Sets the vehicle emergency state\n", "max": 6, "min": 0, "name": "ADSB_EMERGC", "rebootRequired": true, "shortDesc": "ADSB-Out Emergency State", "type": "Int32", "values": [{"description": "NoEmergency", "value": 0}, {"description": "General", "value": 1}, {"description": "Medical", "value": 2}, {"description": "LowFuel", "value": 3}, {"description": "NoCommunications", "value": 4}, {"description": "Interference", "value": 5}, {"description": "Downed", "value": 6}]}, {"category": "Standard", "default": 14, "group": "ADSB", "longDesc": "Configure the emitter type of the vehicle.\n", "max": 19, "min": 0, "name": "ADSB_EMIT_TYPE", "rebootRequired": true, "shortDesc": "ADSB-Out Vehicle Emitter Type", "type": "Int32", "values": [{"description": "Unknown", "value": 0}, {"description": "Light", "value": 1}, {"description": "Small", "value": 2}, {"description": "Large", "value": 3}, {"description": "HighVortex", "value": 4}, {"description": "Heavy", "value": 5}, {"description": "Performance", "value": 6}, {"description": "Rotorcraft", "value": 7}, {"description": "RESERVED", "value": 8}, {"description": "Glider", "value": 9}, {"description": "LightAir", "value": 10}, {"description": "Parachute", "value": 11}, {"description": "UltraLight", "value": 12}, {"description": "RESERVED", "value": 13}, {"description": "UAV", "value": 14}, {"description": "Space", "value": 15}, {"description": "RESERVED", "value": 16}, {"description": "EmergencySurf", "value": 17}, {"description": "ServiceSurf", "value": 18}, {"description": "PointObstacle", "value": 19}]}, {"category": "Standard", "default": 0, "group": "ADSB", "longDesc": "Sets GPS lataral offset encoding\n", "max": 7, "min": 0, "name": "ADSB_GPS_OFF_LAT", "rebootRequired": true, "shortDesc": "ADSB-Out GPS Offset lat", "type": "Int32", "values": [{"description": "NoData", "value": 0}, {"description": "LatLeft2M", "value": 1}, {"description": "LatLeft4M", "value": 2}, {"description": "LatLeft6M", "value": 3}, {"description": "LatRight0M", "value": 4}, {"description": "LatRight2M", "value": 5}, {"description": "LatRight4M", "value": 6}, {"description": "LatRight6M", "value": 7}]}, {"category": "Standard", "default": 0, "group": "ADSB", "longDesc": "Sets GPS longitudinal offset encoding\n", "max": 1, "min": 0, "name": "ADSB_GPS_OFF_LON", "rebootRequired": true, "shortDesc": "ADSB-Out GPS Offset lon", "type": "Int32", "values": [{"description": "NoData", "value": 0}, {"description": "AppliedBySensor", "value": 1}]}, {"category": "Standard", "default": -1, "group": "ADSB", "longDesc": "Vehicle ICAO ID. Use -1 to disable.\n", "max": 16777215, "min": -1, "name": "ADSB_ICAO_ID", "rebootRequired": true, "shortDesc": "ADSB-Out ICAO ID", "type": "Int32"}, {"category": "Standard", "default": -1, "group": "ADSB", "longDesc": "Optional second ownship ICAO ID used to filter self-detections. Use -1 to disable.\n", "max": 16777215, "min": -1, "name": "ADSB_ICAO_ID_2", "rebootRequired": true, "shortDesc": "Secondary ownship ICAO ID", "type": "Int32"}, {"category": "Standard", "default": 0, "group": "ADSB", "longDesc": "This vehicle is always tracked. Use 0 to disable.\n", "max": 16777215, "min": 0, "name": "ADSB_ICAO_SPECL", "rebootRequired": true, "shortDesc": "ADSB-In Special ICAO configuration", "type": "Int32"}, {"category": "Standard", "default": 0, "group": "ADSB", "longDesc": "Enable Identification of Position feature\n", "name": "ADSB_IDENT", "rebootRequired": true, "shortDesc": "ADSB-Out Ident Configuration", "type": "Int32", "values": [{"description": "Disabled", "value": 0}, {"description": "Enabled", "value": 1}]}, {"category": "Standard", "default": 1, "group": "ADSB", "longDesc": "Report the length and width of the vehicle in meters. In most cases, use '1' for the smallest vehicle size.\n", "max": 15, "min": 0, "name": "ADSB_LEN_WIDTH", "rebootRequired": true, "shortDesc": "ADSB-Out Vehicle Size Configuration", "type": "Int32", "values": [{"description": "SizeUnknown", "value": 0}, {"description": "Len15_Wid23", "value": 1}, {"description": "Len25_Wid28", "value": 2}, {"description": "Len25_Wid34", "value": 3}, {"description": "Len35_Wid3Line truncated
|
||||
Reference in new issue
Block a user