5.5 KiB
ZenFC H743
:::warning PX4 does not manufacture this (or any) autopilot. Contact the manufacturer for hardware support or compliance issues. :::
The ZenFC H743 is a flight controller designed by Zenithra Tech. It is built around the STM32H743 processor with dual Bosch BMI088 IMUs for sensor redundancy, an onboard barometer, and an integrated OSD.
:::info This flight controller is manufacturer supported. :::
주요 특징
- MCU:
- STM32H743VIT6 (32-bit Arm® Cortex®-M7, 480 MHz)
- IMU:
- 2x Bosch BMI088 (accel + gyro, independent SPI buses for redundancy)
- Barometer:
- Bosch BMP388
- OSD:
- Onboard AT7456E OSD chip
- Interfaces:
- 7x UARTs
- CAN 1개
- 2x external I2C (I2C1 with GPS connector and dedicated I2C2 connector)
- 8x PWM outputs (Dshot supported)
- microSD card slot
- 1x USB Type-C
- Power:
- 2x ADC (V_BAT & current sense)
- Battery Input range - 2S-6S
- BEC Outputs
- 9V 3A cont.
- 5V 3A cont.
크기
- Mounting: 30.5 mm x 30.5 mm /Φ4mm hole
- Dimensions: 35mm x 35mm x 8mm
- Weight: 9g
구매처
Order from Zenithra Tech.
Flight Controller Layout
시리얼 포트 매핑
| UART | 장치 | PX4 Port |
|---|---|---|
| USART1 | /dev/ttyS0 | GPS1 |
| USART2 | /dev/ttyS1 | TEL3 |
| USART3 | /dev/ttyS2 | TEL4 |
| UART5 | /dev/ttyS3 | TEL1 |
| USART6 | /dev/ttyS4 | RC |
| UART7 | /dev/ttyS5 | TEL2 |
| UART8 | /dev/ttyS6 | UART6 |
Connectors & Pinout
Board uses JST SH connectors for all interfaces.
Note - SBus pin on DJI O3/O4 port is internally connected to RX6 (RCIN).
PWM 출력
The 8 outputs are in 3 groups:
- Outputs 1-4 in group1
- Outputs 5-6 in group2
- Outputs 7-8 in group3
Note:
- All outputs support PWM and DShot protocol. Outputs 1-6 and 8 support "bidirectional DShot" (or "BDShot") telemetry.
- Outputs 1-4 default to DShot300 (PWM_MAIN_TIM0 =
-4); outputs 5-6 and 7-8 default to PWM at 400 Hz. - Each group's protocol can be changed independently using the corresponding
PWM_MAIN_TIMxparameter, including to Bidirectional DShot (BDShot) for ESC telemetry.
디버그 포트
This board does not configure a dedicated UART as a system console. Use the MAVLink Shell over USB for console/NSH access using QGroundControl.
SWD
The board features a 4-pin SWD Debug interface (3V3 / SWCLK / SWDIO / GND) for hardware debugging.
무선 조종
A Radio Control (RC) system is required if you want to manually control your vehicle (PX4 does not require a radio system for autonomous flight modes). See Radio Control modules for the list of supported protocols.
RC input is mapped to USART6 (/dev/ttyS4, RC port).
The port supports both single-wire inverted SBUS and full-duplex protocols with telemetry return (such as CRSF), and the receiver protocol is auto-detected by default (RC_INPUT_PROTO = -1).
PX4 설정
In addition to the basic configuration, the following parameter is important:
| Parameter | 설정 |
|---|---|
| SYS_HAS_MAG | Disabled by default since the board has no internal magnetometer. Enable it if you attach an external mag. |
펌웨어 빌드
To build PX4 for this target:
make zenfc_h743_default
펌웨어 설치
펌웨어는 일반적인 방법으로 설치할 수 있습니다.
-
Build and upload the source:
make zenfc_h743_default upload -
Load the firmware using QGroundControl. 미리 빌드된 펌웨어나 사용자 지정 펌웨어를 사용할 수 있습니다.
The board uses the standard PX4 bootloader, so it follows the same generic LED indications as most other boards (Red = Bootloader/Error, Blue = Active/Activity, Green = Powered).





