PX4 runs every frame type in the Airframe Reference on any flight controller with enough outputs, so these sections said nothing specific to the board. The board page template no longer includes them. Assisted-by: Claude:claude-opus-5-5 Signed-off-by: Hamish Willee <hamishwillee@gmail.com>
6.1 KiB
CUAV X25-EVO
::: warning PX4 does not manufacture this (or any) autopilot. Contact the manufacturer for hardware support or compliance issues. :::
The X25-EVO is an advanced autopilot manufactured by CUAV®.
The autopilot is recommended for commercial system integration but is also suitable for academic research and any other applications.
The X25-EVO brings you ultimate performance, stability, and reliability in every aspect.
::: info These flight controllers are manufacturer supported. :::
Features
- Arm® Cortex-M7® processor (STM32H743XI) with Floating-Point Unit (FPU), operating at 480MHz, and featuring 2MB Flash memory. Enables developers to enhance productivity and efficiency, allowing for more complex algorithms and models.
- Automotive-grade RM3100 compass. Designed for better stability and anti-interference capability.
- Triple-redundant IMUs and dual-redundant barometers located on separate buses. If the PX4 autopilot detects a sensor failure, the system seamlessly switches to another sensor to maintain flight control reliability.
- Independent LDO power control supplies power to each sensor group. A vibration isolation system filters high-frequency vibrations and reduces noise to ensure accurate readings, enabling better overall flight performance for the vehicle.
- Integrated Microchip Ethernet PHY for high-speed communication with onboard devices like mission computers via Ethernet.
- Dual temperature compensation systems, located on the IMU board and FMU board respectively. Temperature is controlled by onboard heating resistors to achieve the optimal operating temperature for the IMUs.
- PWM servo output voltage switchable between 3.3V or 5V.
- Modular design for DIY carrier boards.
Processors & Sensors
- Main Processor: STM32H743XI
- 32-bit Arm® Cortex®-M7, 480MHz, 2MB Flash, 1MB RAM
- Onboard Sensors:
- Accel/Gyro: IIM42652 (x2)
- Accel/Gyro: IIM42653
- Magnetometer: RM3100
- Barometer: BMP581
- Barometer: ICP-20100
Electrical Data
- Rated Voltage:
- Input Voltage: 10~18V
- USB Power Input: 4.75~5.25V
- Servo Rail Input: 0~9.9V
- Rated Current:
- Total Output Max Current: 10A
TELEM1andTELEM2Output Current limiter: 4ACAN1andCAN2Output Current limiter: 2.4A- Other Ports Output Current limiter: 1.5A
Interfaces
- 16x PWM Servo Outputs
- 1x Dedicated R/C Input(
RC IN) for Spektrum / DSM and S.Bus - 1x Analog/PWM RSSI Input
- 2x TELEM Ports (with full flow control)
- 1x UART4 Port
- 2x GPS Ports
- 1x Full GPS plus Safety Switch Port (GPS1)
- 1x Basic GPS Port (with I2C, GPS2)
- 1x USB Port (TYPE-C)
- 1x Ethernet Port
- Transformerless application
- 100Mbps
- 3x I2C Bus Ports
- 1x SPI Bus
- 1x Chip Select Line
- 1x Data Ready Line
- 1x SPI Reset Line
- 5x CAN Ports for CAN Peripherals
- 3x CAN1 Bus Multiplexed Ports
- 2x CAN2 Bus Multiplexed Ports
- 2x Power Input Ports
- DroneCAN/UAVCAN Power Input
- 2x AD Ports
- Analog Input (3.3V)
- Analog Input (6.6V - not supported by PX4)
- 1x Dedicated Debug Port
- FMU Debug
Mechanical Data
Purchase Channels
Order from CUAV.
Assembly/Setup
The X25 EVO Wiring Quick Start provides instructions on how to assemble required/important peripherals including GPS, Power Module etc.
Pinouts
Serial Port Mapping
| UART | Device | Port |
|---|---|---|
| USART1 | /dev/ttyS0 | GPS1 |
| USART2 | /dev/ttyS1 | GPS2 |
| USART3 | /dev/ttyS2 | Debug Console |
| UART4 | /dev/ttyS3 | UART4 |
| UART5 | /dev/ttyS4 | TELEM2 |
| USART6 | /dev/ttyS5 | RC IN |
| UART7 | /dev/ttyS6 | TELEM1 |
PWM Outputs
This flight controller supports up to 16 FMU PWM outputs (MAIN).
Outputs:
- Outputs 1-8 support DShot.
- Outputs 9-16 do not support DShot.
- Outputs 1-7 support Bidirectional DShot.
- Output 8 supports Bidirectional DShot output only (no eRPM capture).
The 16 outputs are in 5 groups:
- Outputs 1-4 in group1 (Timer5)
- Outputs 5-8 in group2 (Timer4)
- Outputs 9-11 in group3 (Timer1)
- Outputs 12-14 in group4 (Timer8)
- Outputs 15-16 in group5 (Timer12)
All outputs within the same group must use the same output protocol and rate.
Voltage Ratings
The X25-EVO achieves triple redundancy on power supplies if three power sources are provided.
The three power rails are POWERC1, POWERC2, and USB.
- POWER C1 and POWER C2 are DroneCAN/UAVCAN battery interfaces.
Normal Operation Maximum Ratings
Under these conditions, all power sources will be used to power the system in the following order:
- POWER C1 and POWER C2 Inputs (10V to 18V)
- USB Input (4.75V to 5.25V)
Voltage monitoring
Digital DroneCAN/UAVCAN battery monitoring is enabled by default.
Building Firmware
::: tip Most users do not need to build this firmware! It is pre-built and installed automatically by QGroundControl when the appropriate hardware is connected. :::
To build PX4 for this target, execute:
make cuav_x25-evo_default
Debug Port
The PX4 System Console and SWD Interface operate on the FMU Debug port.
| Pin | Signal | Volt |
|---|---|---|
| 1 (red) | 5V+ | +5V |
| 2 (blk) | DEBUG TX (OUT) | +3.3V |
| 3 (blk) | DEBUG RX (IN) | +3.3V |
| 4 (blk) | FMU_SWDIO | +3.3V |
| 5 (blk) | FMU_SWCLK | +3.3V |
| 6 (blk) | GND | GND |


