mirror of
https://github.com/PX4/PX4-Autopilot.git
synced 2026-11-22 14:19:57 +08:00
* docs(boards): restructure ARKV6X page to the board page template Move the existing content into the flight-controller page template's sections, headings and anchors, with no change to what the page says, so that the content additions that follow can be reviewed on their own. The flat Sensors, Microprocessor, Other Features, Power Requirements and Additional Information lists become Specifications sub-sections, Where to Buy moves after them, and See Also becomes Further Information. Port labels are in code style, and headings, units and spelling follow the docs style guide. No page links to the anchors that changed. Assisted-by: Claude:claude-opus-5-5 Signed-off-by: Hamish Willee <hamishwillee@gmail.com> * docs(boards): add ARKV6X specifications, PWM outputs and setup sections Fill in the sections the board page template expects, from the board source (boards/ark/fmu-v6x) and ARK's own documentation. - Specifications: core, IO processor, sensor buses, the IIM-42653 Extended Range variant, interface counts, power monitoring and operating temperature - PWM Outputs: FMU outputs, DShot and bidirectional DShot support, timer groups, PX4IO outputs on carriers that have one, and the FMU_CAP capture channel - Power, Voltage Ratings, Ethernet, SD Card, Assembly (Radio Control, GPS & Compass, Telemetry, CAN) and Debug Port, describing the ARK PAB Carrier where the connectors depend on the carrier - Serial Port Mapping: flow control column, and GPS1 label - Version badge, firmware build tip, and links to ARK's current docs, datasheet and 3D model Assisted-by: Claude:claude-opus-5-5 Signed-off-by: Hamish Willee <hamishwillee@gmail.com> * docs(boards): fix ARKV6X version badge and voltage ratings The ARKV6X target was backported to the 1.13 branch and first shipped in v1.13.1, so the badge said the board wasn't supported on v1.13.x when it is. The voltage ratings had been taken from the Pixhawk 6X, and claimed the power inputs survive up to 10 V. ARK's datasheet gives 4.8 V minimum and 5.5 V absolute maximum for the module, so use ARK's figures, with the ARK PAB Carrier's input priority and protection thresholds from its own page. Assisted-by: Claude:claude-opus-5-5 Signed-off-by: Hamish Willee <hamishwillee@gmail.com> * docs(boards): apply ARKV6X review style fixes Apply the style findings from review: carrier port labels as printed (UART4/I2C3, RC/SBUS), MCU peripheral names as plain text and device paths in code, links for the first use of terms the page relies on, the Radio Controller option label, the carrier's unsupported PPM and DSM ports, Ethernet speed, mounting hole spacing, and the board's other build targets. Assisted-by: Claude:claude-opus-5-5 Signed-off-by: Hamish Willee <hamishwillee@gmail.com> * docs(boards): apply ARKV6X review minor fixes Link ARK's and InvenSense's canonical URLs rather than ones that redirect, give the input voltage range from ARK's datasheet, count power monitoring by power inputs, and drop casual italics. Assisted-by: Claude:claude-opus-5-5 Signed-off-by: Hamish Willee <hamishwillee@gmail.com> * docs(boards): apply ARKV6X review fixes Apply the fixes from dakejahl's review of #29587, checked against the carrier schematic and the board source. Correct the stale ARK PAB Carrier voltage thresholds and warn that inputs above the module's 5.5 V absolute maximum still pass through. Note that the Extended Range needs v1.14. Cover DSM binding and power on the RC/SBUS port, FMU_CAP as a PWM output, encrypted_logs output labelling, and INA238 setup for the 12S PAB power module. Format the USB pin table on the PAB page. Assisted-by: Claude:claude-opus-5-5 Signed-off-by: Hamish Willee <hamishwillee@gmail.com> * docs(boards): apply ARKV6X board review fixes A board docs review against the board source and sibling pages found that the ARKV6X Ethernet uses a static 192.168.0.4 address with no DHCP, so the defaults on the linked Ethernet setup page don't apply. It also found that the DSM port can't be read in any build, because it carries only a timer capture pin, and that the encrypted_logs build loses the carrier's PX4IO outputs and RC input as well as the output labels. Align the reference-design and standards links, Ethernet speed and capture-pin details with the FMUv6X sibling pages, and give the RC/SBUS connector type from ARK. Assisted-by: Claude:claude-opus-5-5 Signed-off-by: Hamish Willee <hamishwillee@gmail.com> --------- Signed-off-by: Hamish Willee <hamishwillee@gmail.com>
9.9 KiB
9.9 KiB
ARK Pixhawk Autopilot Bus Carrier
::: warning PX4 does not manufacture this (or any) autopilot. Contact the manufacturer for hardware support or compliance issues. :::
The ARK Pixhawk Autopilot Bus (PAB) Carrier is a USA-built flight controller carrier board, based on the Pixhawk Autopilot Bus open source standard.
The PAB form factor enables the ARK PAB Carrier to be used with any PAB-compatible flight controller, such as the ARKV6X.
Where To Buy
Order From Ark Electronics (US)
Features
- Pixhawk Autopilot Bus (PAB) Form Factor
- USA Built
Connectors
- PAB Board to Board Interface
- 100 Pin Hirose DF40
- 50 Pin Hirose DF40
- Dual Digital Power Module Inputs
- 5V Input
- I2C Power Monitor
- 6 Pin Molex CLIK-Mate
- Ethernet
- 100Mbps
- Built in Magnetics
- 4 Pin JST-GH
- Full GPS Plus Safety Switch Port
- 10 Pin JST-GH
- Basic GPS Port
- 6 Pin JST-GH
- Dual CAN Ports
- 4 Pin JST-GH
- Triple Telemetry Ports with Flow Control
- 6 Pin JST-GH
- Eight PWM Outputs
- 10 Pin JST-GH
- UART/I2C Port
- 6 Pin JST-GH
- I2C Port
- 4 Pin JST-GH
- PPM RC Port
- 3 Pin JST-GH
- DSM RC Port
- 3 Pin JST-ZH
- SPI Port
- 11 Pin JST-GH
- ADIO Port
- 8 Pin JST-GH
- Debug Port
- 10 Pin JST-SH
Dimensions
- Without Flight Controller Module
- 74.0mm x 43.5mm x 12.0mm
- 22g
Power
- 5V input on
POWER1,POWER2,USB C, and theUSB JST-GHconnector- Input is prioritized in the following order: POWER1 > POWER2 > USB
USB Cand theUSB JST-GHare in parallel- Overvoltage protection at 5.85V
- Undervoltage protection at 3.81V
VDD_5V_HIPOWERandVDD_5V_PERIPHcan each provide a total of 1.5A across all the connectors
LEDS
- There are two LEDs on the ARK PAB
Redis the ethernet power LEDGreenis the ethernet activity LED
Pinout
POWER1
| Pin | Signal | Volt |
|---|---|---|
| 1 (red) | VBRICK1 |
+5.0V |
| 2 (blk) | VBRICK1 |
+5.0V |
| 3 (blk) | I2C1_SCL | +3.3V |
| 4 (blk) | I2C1_SDA | +3.3V |
| 5 (blk) | GND |
GND |
| 6 (blk) | GND |
GND |
POWER2
| Pin | Signal | Volt |
|---|---|---|
| 1 (red) | VBRICK2 |
+5.0V |
| 2 (blk) | VBRICK2 |
+5.0V |
| 3 (blk) | I2C2_SCL | +3.3V |
| 4 (blk) | I2C2_SDA | +3.3V |
| 5 (blk) | GND |
GND |
| 6 (blk) | GND |
GND |
PWM
| Pin | Signal | Volt |
|---|---|---|
| 1 (red) | VDD_SERVO (Not Connected) | +5.0V |
| 2 (blk) | FMU_CH1 | +3.3V |
| 3 (blk) | FMU_CH2 | +3.3V |
| 4 (blk) | FMU_CH3 | +3.3V |
| 5 (blk) | FMU_CH4 | +3.3V |
| 6 (blk) | FMU_CH5 | +3.3V |
| 7 (blk) | FMU_CH6 | +3.3V |
| 8 (blk) | FMU_CH7 | +3.3V |
| 9 (blk) | FMU_CH8 | +3.3V |
| 10 (blk) | GND |
GND |
GPS1
| Pin | Signal | Volt |
|---|---|---|
| 1 (red) | VDD_5V_PERIPH |
+5.0V |
| 2 (blk) | USART1_TX_GPS1 | +3.3V |
| 3 (blk) | USART1_RX_GPS1 | +3.3V |
| 4 (blk) | I2C1_SCL | +3.3V |
| 5 (blk) | I2C1_SDA | +3.3V |
| 6 (blk) | nSAFETY_SWITCH_IN | +3.3V |
| 7 (blk) | nSAFETY_SWITCH_LED_OUT | +3.3V |
| 8 (blk) | 3V3_FMU |
+3.3V |
| 9 (blk) | BUZZER | +5.0V |
| 10 (blk) | GND |
GND |
GPS2
| Pin | Signal | Volt |
|---|---|---|
| 1 (red) | VDD_5V_HIPOWER |
+5.0V |
| 2 (blk) | UART8_TX_GPS2 | +3.3V |
| 3 (blk) | UART8_RX_GPS2 | +3.3V |
| 4 (blk) | I2C2_SCL | +3.3V |
| 5 (blk) | I2C2_SDA | +3.3V |
| 6 (blk) | GND |
GND |
TELEM1
| Pin | Signal | Volt |
|---|---|---|
| 1 (red) | VDD_5V_HIPOWER |
+5.0V |
| 2 (blk) | UART7_TX | +3.3V |
| 3 (blk) | UART7_RX | +3.3V |
| 4 (blk) | UART7_CTS | +3.3V |
| 5 (blk) | UART7_RTS | +3.3V |
| 6 (blk) | GND |
GND |
TELEM2
| Pin | Signal | Volt |
|---|---|---|
| 1 (red) | VDD_5V_PERIPH |
+5.0V |
| 2 (blk) | UART5_TX | +3.3V |
| 3 (blk) | UART5_RX | +3.3V |
| 4 (blk) | UART5_CTS | +3.3V |
| 5 (blk) | UART5_RTS | +3.3V |
| 6 (blk) | GND |
GND |
TELEM3
| Pin | Signal | Volt |
|---|---|---|
| 1 (red) | VDD_5V_HIPOWER |
+5.0V |
| 2 (blk) | USART2_TX | +3.3V |
| 3 (blk) | USART2_RX | +3.3V |
| 4 (blk) | USART2_CTS | +3.3V |
| 5 (blk) | USART2_RTS | +3.3V |
| 6 (blk) | GND |
GND |
UART4/I2C3
| Pin | Signal | Volt |
|---|---|---|
| 1 (red) | VDD_5V_PERIPH |
+5.0V |
| 2 (blk) | UART4_TX | +3.3V |
| 3 (blk) | UART4_RX | +3.3V |
| 4 (blk) | I2C3_SCL | +3.3V |
| 5 (blk) | I2C3_SDA | +3.3V |
| 6 (blk) | GND |
GND |
I2C3
| Pin | Signal | Volt |
|---|---|---|
| 1 (red) | VDD_5V_PERIPH |
+5.0V |
| 2 (blk) | I2C3_SCL | +3.3V |
| 3 (blk) | I2C3_SDA | +3.3V |
| 4 (blk) | GND |
GND |
CAN1
| Pin | Signal | Volt |
|---|---|---|
| 1 (red) | VDD_5V_HIPOWER |
+5.0V |
| 2 (blk) | CAN1_H | +3.3V |
| 3 (blk) | CAN1_L | +3.3V |
| 4 (blk) | GND |
GND |
CAN2
| Pin | Signal | Volt |
|---|---|---|
| 1 (red) | VDD_5V_PERIPH |
+5.0V |
| 2 (blk) | CAN2_H | +3.3V |
| 3 (blk) | CAN2_L | +3.3V |
| 4 (blk) | GND |
GND |
USB
All signals in parallel with USB C connector
| Pin | Signal | Volt |
|---|---|---|
| 1 (red) | VBUS_IN |
+5.0V |
| 2 (blk) | USB_N | +3.3V |
| 3 (blk) | USB_P | +3.3V |
| 4 (blk) | GND |
GND |
ETH
| Pin | Signal | Volt |
|---|---|---|
| 1 (red) | ETH_RD_N | +50.0V Tolerant |
| 2 (blk) | ETH_RD_P | +50.0V Tolerant |
| 3 (blk) | ETH_TD_N | +50.0V Tolerant |
| 4 (blk) | ETH_TD_P | +50.0V Tolerant |
ADIO
| Pin | Signal | Volt |
|---|---|---|
| 1 (red) | VDD_5V_PERIPH |
+5.0V |
| 2 (blk) | FMU_CAP | +3.3V |
| 3 (blk) | BOOTLOADER | +3.3V |
| 4 (blk) | FMU_RST_REQ | +3.3V |
| 5 (blk) | nARMED | +3.3V |
| 6 (blk) | ADC1_3V3 | +3.3V |
| 7 (blk) | ADC1_6V6 | +3.3V |
| 8 (blk) | GND |
GND |
RC/SBUS
| Pin | Signal | Volt |
|---|---|---|
| 1 (red) | VDD_5V_SBUS_RC |
+5.0V |
| 2 (blk) | USART6_RX_SBUS_IN | +3.3V |
| 3 (blk) | USART6_TX | +3.3V |
| 4 (blk) | VDD_3V3_SPEKTRUM |
+3.3V |
| 5 (blk) | GND |
GND |
PPM
| Pin | Signal | Volt |
|---|---|---|
| 1 (red) | VDD_5V_PPM_RC |
+5.0V |
| 2 (blk) | DSM_INPUT/FMU_PPM_INPUT | +3.3V |
| 3 (blk) | GND |
GND |
DSM
| Pin | Signal | Volt |
|---|---|---|
| 1 (red) | VDD_3V3_SPEKTRUM |
+3.3V |
| 2 (blk) | GND |
GND |
| 3 (blk) | DSM_INPUT/FMU_PPM_INPUT | +3.3V |
SPI6
| Pin | Signal | Volt |
|---|---|---|
| 1 (red) | VDD_5V_PERIPH |
+5.0V |
| 2 (blk) | SPI6_SCK | +3.3V |
| 3 (blk) | SPI6_MISO | +3.3V |
| 4 (blk) | SPI6_MOSI | +3.3V |
| 5 (blk) | SPI6_nCS1 | +3.3V |
| 6 (blk) | SPI6_nCS2 | +3.3V |
| 7 (blk) | SPIX_nSYNC | +3.3V |
| 8 (blk) | SPI6_DRDY1 | +3.3V |
| 9 (blk) | SPI6_DRDY2 | +3.3V |
| 10 (blk) | SPI6_nRESET | +3.3V |
| 11 (blk) | GND |
GND |
Debug Port
The PX4 System Console and SWD interface run on the FMU Debug port.
The pinouts and connector comply with the Pixhawk Debug Full interface defined in the Pixhawk Connector Standard interface (JST SM10B connector).
| Pin | Signal | Volt |
|---|---|---|
| 1 (red) | Vtref |
+3.3V |
| 2 (blk) | Console TX (OUT) | +3.3V |
| 3 (blk) | Console RX (IN) | +3.3V |
| 4 (blk) | SWDIO |
+3.3V |
| 5 (blk) | SWCLK |
+3.3V |
| 6 (blk) | SWO |
+3.3V |
| 7 (blk) | NFC GPIO | +3.3V |
| 8 (blk) | PH11 | +3.3V |
| 9 (blk) | nRST | +3.3V |
| 10 (blk) | GND |
GND |
For information about using this port see:
- SWD Debug Port
- PX4 System Console (Note, the FMU console maps to USART3).
See Also
- ARK Pixhawk Autopilot Bus Carrier (ARK Docs)



