Files
PX4-Autopilot/docs/assets/flight_controller
52c4777580 docs(boards): add Accton Godwit G-FH7 flight controller page (#28830)
* Add new board "accton_godwit gfh7"

* Adjust the spacing.

* docs(boards/accton-godwit): Add support for the accton-godwit_gfh7 flight controller documentations.

* docs(boards): align Accton Godwit GFH7 page with board template

Bring the new GFH7 page in line with the flight controller page
template and the board's own configuration, so readers can wire and
set up the board from it:

- Fix image paths (all images were broken) and resize/compress the
  images; split the tall wiring diagram into two.
- Use PX4 port labels and /dev/ttyS* devices in the serial port table
  instead of ArduPilot SERIALn numbering, matching default.px4board.
- State 8 PWM outputs (PWM9 only drives NeoPixel LEDs), with DShot,
  bidirectional DShot and timer groups.
- Explain how to enable CRSF/ELRS on the ELRS connector, since only
  S.BUS is started by default.
- Add the standard notes and missing sections (Power, CAN, OSD, SD
  card, debug port), the _default build target and QGC tip.

Assisted-by: Claude:claude-opus-5-5
Signed-off-by: Hamish Willee <hamishwillee@gmail.com>

* add voltage description.

* modify doc description about UART、pinout.

* modified UART settings

* modified UART device description

* docs(boards/accton-godwit): tidy GFH7 voltage ratings section

Give the section its own heading and anchor, name the battery input after the VBAT pins, and drop the battery ratings that contradict each other (48V maximum vs 12S, and an undamaged range below the operating range) until the manufacturer confirms the values.

Assisted-by: Claude:claude-opus-5-5
Signed-off-by: Hamish Willee <hamishwillee@gmail.com>

* docs(boards/accton-godwit): note GFH7 ships with PX4 bootloader

Assisted-by: Claude:claude-opus-5-5
Signed-off-by: Hamish Willee <hamishwillee@gmail.com>

* Modify these messages:
1.RCDGV pad group.
2.Voltage Ratings info.

* modified message:
1. UART port description
2. Telemetry Radios description

* docs(boards/accton-godwit): match GFH7 page to the new serial port labels

#28817 moves the PX4 RC port to the SBUS connector (UART5), labels the
ELRS connector (UART4) TELEM/SERIAL 4 and the receive-only ESC telemetry
UART (USART1) EXT2, and fixes the 12 V enable polarity. Update the radio,
serial port mapping, power and debug build notes to match.

Assisted-by: Kiro:claude-opus-5.5

* chore(boards/accton-godwit): drop GFH7 board files from the docs branch

The board port is reviewed and updated in #28817. The copies here had
already drifted from it (for example TEL3 on /dev/ttyS7, which does not
exist), so keep this pull request to the documentation only.

Assisted-by: Kiro:claude-opus-5.5

* docs(boards/accton-godwit): document the GFH7 ELRS default and IMU heater

#28817 makes CRSF/ELRS on the ELRS connector the default RC input, turns
S.BUS off by default, and adds the IMU heater (off by default). Update
the radio, serial port mapping and debug build notes to match, and add
an IMU Heater section that explains how to enable it.

Assisted-by: Kiro:claude-opus-5.5

* docs(boards/accton-godwit): add GFH7 block diagram

Review on #28830 asked for a block diagram of the main components
(sensors, power supply), as required by the board support guide.

Assisted-by: Kiro:claude-opus-5.5
Signed-off-by: g945643frankie <g945643@oz.nthu.edu.tw>

* docs(boards/accton-godwit): note GFH7 boots in Stabilized mode

The board sets COM_FLTMODE_BOOT to Stabilized instead of the PX4
default of Hold, so users should know which mode they get on power-up
and that a mode switch overrides it.

Assisted-by: Kiro:claude-opus-5.5
Signed-off-by: g945643frankie <g945643@oz.nthu.edu.tw>

* docs(boards/accton-godwit): fix GFH7 debug port tables

* docs(boards/accton-godwit): list GFH7 OSD debug pads in board order

* docs(accton-godwit_gfh7): reference QGC board recognition PR in tip

Point the Building Firmware tip at mavlink/qgroundcontrol#15212 so it is accurate until QGC recognises GFH7.

* docs(boards/accton-godwit): fix GFH7 review issues

The block diagram named the wrong secondary IMU, the firmware tip linked
a QGC PR that was closed unmerged, and the S.BUS pin on the D-VTX
connector (shown in the pinout) was undocumented. Also tidy the
telemetry and debug port sections to the style guide.

Assisted-by: Claude:claude-opus-5-5
Signed-off-by: Hamish Willee <hamishwillee@gmail.com>

* docs(boards/accton-godwit): clarify GFH7 voltage ratings and label SBUS connector

Describe the 13V figure as the minimum for the 12V camera/VTX rail instead of a tested operating minimum, drop the unmeasured USB operational range, and relabel the UART5 connector in the block diagram as SBUS.

Signed-off-by: g945643frankie <g945643@oz.nthu.edu.tw>

* docs(boards): reorder Accton Godwit GFH7 page to match board template

Match the flight controller page template so the page reads like other
board pages, and keep the images in a folder named after the page.

Assisted-by: Claude:claude-opus-5-5
Signed-off-by: Hamish Willee <hamishwillee@gmail.com>

* docs(boards): tidy Accton Godwit GFH7 page and add release note

Address the remaining editorial review findings so the page matches the
board template and other board pages, and list the new board in the
release notes.

Assisted-by: Claude:claude-opus-5-5
Signed-off-by: Hamish Willee <hamishwillee@gmail.com>

* docs(boards): rename to G-FH7 and address review questions

Rename the reader-facing board name from GFH7 to G-FH7 in the board
page, sidebar, manufacturer list, and main release notes.

State the battery input as up to 12S LiPo, note that the IMU heater
current is calculated from the resistor value (not measured), correct
the UART5 wiring for the SBUS and A-VTX connectors, and link the
IST8310 datasheet.

Signed-off-by: g945643frankie <g945643@oz.nthu.edu.tw>

* docs(boards): update G-FH7 pin definition image

Replace the pinout with the updated drawing that labels UART5_TX on the
A-VTX connector and UART5_TX/UART5_RX on the SBUS connector.

Signed-off-by: g945643frankie <g945643@oz.nthu.edu.tw>

* docs(boards): tidy G-FH7 UART5 wording and block diagram battery label

Put the S.BUS setup line first in the SBUS receiver bullet, so "To use
it" refers to the receiver rather than the A-VTX TX pin, and shorten the
UART5 serial table cell and the duplicated heater current note.

Change the block diagram battery label from "4~12S" to "Up to 12S",
since the authors confirmed there is no verified lower limit and the
page now says "Up to 12S LiPo".

Assisted-by: Claude:claude-opus-5-5
Signed-off-by: Hamish Willee <hamishwillee@gmail.com>

* docs(boards): document G-FH7 A-VTX control and VTX driver

The A-VTX TX pin is the SmartAudio/Tramp control line, shared with
UART5_TX on the SBUS connector. Document how to use it (VTX_SER_CFG set
to Radio Controller) and that it can't be used together with an S.BUS
receiver on the SBUS connector.

Signed-off-by: g945643frankie <g945643@oz.nthu.edu.tw>

* docs(boards): fix G-FH7 RC, buzzer and wording review issues

Tell readers to disable CRSF when enabling DSM or GHST, since CRSF is
on TELEM/SERIAL 4 by default, and note that DSM receivers can't be bound
from PX4 because the board defines no SPEKTRUM_POWER. Say the BZ output
needs an active buzzer, because the board drives it as a plain GPIO.

Also define DFU, PPS and VTX at first use, link parameter setting, use
"co-processor" for the OSD consistently, fix ambiguous references in
the OSD and debug pad text, and narrow the debug-build ELRS limit to
the ELRS connector.

Assisted-by: Claude:claude-opus-5-5
Signed-off-by: Hamish Willee <hamishwillee@gmail.com>

* docs: G-FH7: remove VTX control, apply ADC/power monitoring suggestions

PX4's VTX driver swaps RX/TX on the RC port (no RC_SERIAL_SWAP_RXTX on
this board), so SmartAudio/Tramp would not come out on the A-VTX TX pin.
State that PX4 does not use that pin instead.

Signed-off-by: g945643frankie <g945643@oz.nthu.edu.tw>

* Update docs/en/flight_controller/accton-godwit_gfh7.md

* Update docs/en/flight_controller/accton-godwit_gfh7.md

* Update docs/en/releases/main.md

* docs(accton-godwit_gfh7): address review feedback

Apply remaining Hamish review suggestions on the G-FH7 board page:
clarify the switchable 12 V BEC output, note serial flashing over TELEM only,
expand GHST as TBS Ghost, warn that 3.3 V DSM receivers need a separate supply,
and match the OSD SWD pad wording to the FMU debug table.

* docs(boards): tidy G-FH7 interface, power, BOOT and ESC wiring text

Move the Interface Summary under Pinouts to match the board page
template, note that current monitoring needs setup, name the board's
BOOT button, and describe the ESC wiring diagram as it is drawn
(4-in-1 ESC on the ESC connector only).

Assisted-by: Claude:claude-opus-5-5
Signed-off-by: Hamish Willee <hamishwillee@gmail.com>

* docs(boards): flatten G-FH7 images onto white for dark mode

The board drawings were black line art on a transparent background, so
in dark mode the lines all but vanished against the dark page.

Assisted-by: Claude:claude-opus-5-5
Signed-off-by: Hamish Willee <hamishwillee@gmail.com>

* docs(boards): drop space between value and unit on G-FH7 page

PX4 prefers no space between a value and its unit symbol (3V, not 3 V).

Assisted-by: Claude:claude-opus-5-5
Signed-off-by: Hamish Willee <hamishwillee@gmail.com>

---------

Signed-off-by: Hamish Willee <hamishwillee@gmail.com>
Signed-off-by: g945643frankie <g945643@oz.nthu.edu.tw>
Co-authored-by: Hamish Willee <hamishwillee@gmail.com>
Co-authored-by: g945643frankie <g945643@oz.nthu.edu.tw>
Co-authored-by: g945643frankie <106499958+g945643frankie@users.noreply.github.com>
2026-11-18 18:34:48 +11:00
..
…
…