# 안전장치 시뮬레이션
[Failsafes](../config/safety.md) define the safe limits/conditions under which you can safely use PX4, and the action that will be performed if a failsafe is triggered (for example, landing, holding position, or returning to a specified point).
SITL에서는 시뮬레이션 편리성을 위하여, 일부 안전 장치가 기본적으로 비활성화되어 있습니다.
실환경 테스트 이전에 SITL 시뮬레이션에서 안전에 중요한 기능을 테스트하는 방법을 설명합니다.
:::info
You can also test failsafes using [HITL simulation](../simulation/hitl.md).
HITL은 비행 컨트롤러의 일반 설정 매개변수를 사용합니다.
:::
## 데이터 링크 손실
The _Data Link Loss_ failsafe (unavailability of external data via MAVLink) is enabled by default.
따라서 연결된 GCS, SDK 또는 기타 MAVLink 애플리케이션에서만 시뮬레이션 가능합니다.
Set the parameter [NAV_DLL_ACT](../advanced_config/parameter_reference.md#NAV_DLL_ACT) to the desired failsafe action to change the behavior.
For example, set to `0` to disable it.
:::info
All parameters in SITL including this one get reset when you do `make clean`.
:::
## RC 링크 손실
The _RC Link Loss_ failsafe (unavailability of data from a remote control) is enabled by default.
다른 시험을 가로막는 배터리 용량 부족 상태를 유발하지 않고 지상 통제 장치의 배터리 표시를 시험해볼 수 있습니다.
Set the parameter [NAV_RCL_ACT](../advanced_config/parameter_reference.md#NAV_RCL_ACT) to the desired failsafe action to change the behavior.
For example, set to `0` to disable it.
:::info
All parameters in SITL including this one get reset when you do `make clean`.
:::
## 배터리 부족
시뮬레이션된 배터리는 에너지가 고갈되지 않도록 구현되며, 기본적으로 용량의 50%까지만 소모되므로 보고된 전압이 표시됩니다. pxh shell의 SITL 인스턴스에서 param set SIM_GPS_BLOCK 1 명령과 param set SIM_GPS_BLOCK 0 명령을 실행하여 GPS 메시지를 차단하고 해제하는 방식으로 시험해볼 수 있습니다.
To change this minimal battery percentage value use the parameter [SIM_BAT_MIN_PCT](../advanced_config/parameter_reference.md#SIM_BAT_MIN_PCT).
To control how fast the battery depletes to the minimal value use the parameter [SIM_BAT_DRAIN](../advanced_config/parameter_reference.md#SIM_BAT_DRAIN).
:::tip
By changing [SIM_BAT_MIN_PCT](../advanced_config/parameter_reference.md#SIM_BAT_MIN_PCT) in flight, you can also test regaining capacity to simulate inaccurate battery state estimation or in-air charging technology.
:::
The simulated battery can be completely disabled by setting [SIM_BAT_DRAIN](../advanced_config/parameter_reference.md#SIM_BAT_DRAIN) to 0. This is useful, for example, if you provide an external battery simulation via MAVLink.
### Multiple Batteries
By default only one battery is simulated.
Additional batteries are simulated by enabling them like on a real vehicle: set the source of the battery to `Power Module` and configure it, e.g. [BAT2_SOURCE](../advanced_config/parameter_reference.md#BAT2_SOURCE) and [BAT2_N_CELLS](../advanced_config/parameter_reference.md#BAT2_N_CELLS) for a second battery.
Each simulated battery is published as its own `battery_status` instance.
All batteries deplete according to [SIM_BAT_DRAIN](../advanced_config/parameter_reference.md#SIM_BAT_DRAIN) and [SIM_BAT_MIN_PCT](../advanced_config/parameter_reference.md#SIM_BAT_MIN_PCT) unless overridden for an individual battery with [SIM_BATx_DRAIN](../advanced_config/parameter_reference.md#SIM_BAT1_DRAIN) and [SIM_BATx_MIN_PCT](../advanced_config/parameter_reference.md#SIM_BAT1_MIN_PCT).
Setting `SIM_BATx_DRAIN` to a non-positive value uses the shared drain time. Setting `SIM_BATx_MIN_PCT` to a negative value
uses the shared minimum charge.
This can be used to test multi-battery behaviour, for example one battery depleting faster than the others.
## 센서/시스템 장애
[Failure injection](../debug/failure_injection.md) can be used to simulate different types of failures in many sensors and systems.
GPS가 없거나 간헐적으로 발생하는 경우, 특정 값에서 멈추거나 멈추는 RC 신호, 회피 시스템의 오류 등을 시뮬레이션 할 수 있습니다.
Failure injection is gated by the [SYS_FAILURE_EN](../advanced_config/parameter_reference.md#SYS_FAILURE_EN) parameter.
For example, to simulate GPS failure, enter the following commands on the SITL instance _pxh shell_:
```sh
# Turn (all) GPS off (no position reported, as for a dead receiver)
failure gps off
# Freeze (all) GPS on the last reported position (a "stuck" fix)
failure gps stuck
# Report a diverging position (offset by ~111 km, trips the GNSS redundancy checks)
failure gps wrong
# Restore normal GPS output
failure gps ok
```
:::tip
To test the [GNSS redundancy failsafe](../advanced_config/parameter_reference.md#COM_GNSSLOSS_ACT) you can simulate a second GPS receiver: set the antenna-offset parameter [SENS_GNSS1_OFFX](../advanced_config/parameter_reference.md#SENS_GNSS1_OFFX) or [SENS_GNSS1_OFFY](../advanced_config/parameter_reference.md#SENS_GNSS1_OFFY) to a non-zero value, and the simulator publishes a second `sensor_gnss` instance offset by that distance (in metres).
You can then fail an individual receiver with the `-i` flag (`-i 0` = all instances, `-i 1` = first GPS, `-i 2` = second), for example `failure gps wrong -i 2`.
:::