# 멀티콥터 PID 튜닝 가이드
This tutorial explains how to _manually_ tune the PID loops on PX4 for all [multicopter setups](../airframes/airframe_reference.md#copter) (Quads, Hexa, Octo etc).
:::tip
[Autotune](../config/autotune_mc.md) is recommended for most users, as it is far faster, easier and provides good tuning for most frames.
예를 들어, 새로운 ESC 또는 모터에는 다른 튜닝 게인이 필요합니다.
:::
Generally if you're using an appropriate [supported frame configuration](../airframes/airframe_reference.md#copter), the default tuning should allow you to fly the vehicle safely.
Tuning is recommended for all new vehicle setups to get the _very best_ performance, because relatively small hardware and assembly changes can affect the gains required tuning gains for optimal flight.
For example, different ESCs or motors change the optimal tuning gains.
## 소개
PX4 uses **P**roportional, **I**integral, **D**erivative (PID) controllers (these are the most widespread control technique).
The _QGroundControl_ **PID Tuning** setup provides real-time plots of the vehicle setpoint and response curves.
The goal of tuning is to set the P/I/D values such that the _Response_ curve matches the _Setpoint_ curve as closely as possible (i.e. a fast response without overshoots).

컨트롤러는 계층화되어 있어 상위 수준의 컨트롤러 결과를 하위 수준의 컨트롤러로 전달합니다.
The lowest-level controller is the **rate controller**, followed by the **attitude controller**, and finally the **velocity & position controller**.
PID 튜닝은 다른 모든 컨트롤러에 영향을 미치므로 속도 컨트롤러부터 시작하여 동일한 순서로 수행해야합니다.
The testing procedure for each controller (rate, attitude, velocity/position) and axis (yaw, roll, pitch) is always the same: create a fast setpoint change by moving the sticks very rapidly and observe the response.
가장 낮은 수준의 컨트롤러는 속도 컨트롤러, 태도 컨트롤러, 마지막으로 속도 & 위치 컨트롤러 입니다.
:::tip
- 속도 컨트롤러 조정이 가장 중요하며 잘 조정된 경우 다른 컨트롤러는 종종 약간의 조정만 필요하거나 필요하지 않습니다.
- 일반적으로 롤 및 피치에 동일한 튜닝 게인을 사용할 수 있습니다.
- 곡예/안정화/고도 모드를 사용하여 속도 컨트롤러 조정
- Use [Position mode](../flight_modes_mc/position.md) to tune the _Velocity Controller_ and the _Position Controller_.
Make sure to switch to the _Simple position control_ mode so you can generate step inputs.

:::
## 전제 조건
- You have selected the closest matching [default frame configuration](../config/airframe.md) for your vehicle.
This should give you a vehicle that already flies.
- You should have done an [ESC calibration](../advanced_config/esc_calibration.md).
- If using PWM outputs their minimum values should be set correctly in the [Actuator Configuration](../config/actuators.md).
These need to be set low, but such that the **motors never stop** when the vehicle is armed.
This can be tested in [Acro mode](../flight_modes_mc/acro.md) or in [Stabilized mode](../flight_modes_mc/manual_stabilized.md):
- Remove propellers
- Arm the vehicle and lower the throttle to the minimum
- Tilt the vehicle to all directions, about 60 degrees
- Check that no motors turn off
- Use a high-rate telemetry link such as WiFi if at all possible (a typical low-range telemetry radio is not fast enough for real-time feedback and plots).
This is particularly important for the rate controller.
- Disable [MC_AIRMODE](../advanced_config/parameter_reference.md#MC_AIRMODE) before tuning a vehicle (there is an options for this in the PID tuning screen).
:::warning
Poorly tuned vehicles are likely to be unstable, and easy to crash.
Make sure to have assigned a [Kill switch](../config/safety.md#emergency-switches).
:::
## Tuning Procedure
The tuning procedure is:
1. Arm the vehicle, takeoff, and hover (typically in [Position mode](../flight_modes_mc/position.md)).
2. Open _QGroundControl_ **Vehicle Setup > PID Tuning**

3. Select the **Rate Controller** tab.
4. Confirm that the airmode selector is set to **Disabled**
5. Set the _Thrust curve_ value to: 0.3 (PWM, power-based controllers) or 1 (RPM-based ESCs)
::: info
For PWM, power-based and (some) UAVCAN speed controllers, the control signal to thrust relationship may not be linear.
As a result, the optimal tuning at hover thrust may not be ideal when the vehicle is operating at higher thrust.
The thrust curve value can be used to compensate for this non-linearity:
- For PWM controllers, 0.3 is a good default (which may benefit from [further tuning](../config_mc/pid_tuning_guide_multicopter.md#thrust-curve)).
- For RPM-based controllers, use 1 (no further tuning is required as these have a quadratic thrust curve).
For more information see the [detailed PID tuning guide](../config_mc/pid_tuning_guide_multicopter.md#thrust-curve).
:::
6. Set the _Select Tuning_ radio button to: **Roll**.
7. (Optionally) Select the **Automatic Flight Mode Switching** checkbox.
This will _automatically_ switch from [Position mode](../flight_modes_mc/position.md) to [Stabilised mode](../flight_modes_mc/manual_stabilized.md) when you press the **Start** button
8. For rate controller tuning switch to _Acro mode_, _Stabilized mode_ or _Altitude mode_ (unless automatic switching is enabled).
9. Select the **Start** button in order to start tracking the setpoint and response curves.
10. Rapidly move the _roll stick_ full range and observe the step response on the plots.
:::tip
Stop tracking to enable easier inspection of the plots.
This happens automatically when you zoom/pan.
Use the **Start** button to restart the plots, and **Clear** to reset them.
:::
11. Modify the three PID values using the sliders (for roll rate-tuning these affect `MC_ROLLRATE_K`, `MC_ROLLRATE_I`, `MC_ROLLRATE_D`) and observe the step response again.
The values are saved to the vehicle as soon as the sliders are moved.
::: info
The goal is for the _Response_ curve to match the _Setpoint_ curve as closely as possible (i.e. a fast response without overshoots).
:::
The PID values can be adjusted as follows:
- P (비례) 또는 K 이득 :
- 더 많은 응답을 위해 이것을 늘리십시오.
- 응답이 오버 슈팅 및/또는 진동하는 경우 감소합니다 (특정 지점까지 D 게인 증가도 도움이 됨).
- D (미분) 이득 :
- 오버슈트 및 진동을 줄이기 위해이 값을 늘릴 수 있습니다.
- 소음을 증폭하고 모터가 뜨거워 질 수 있으므로 필요한 만큼만 늘리십시오.
- I (적분) 이득 :
- 정상 상태 오류를 줄이는 데 사용
- 너무 낮으면 응답이 설정 값에 도달하지 못할 수 있습니다 (예 : 바람)
- 너무 높으면 느린 진동이 발생할 수 있습니다.
12. 피치와 요에 대해 위의 튜닝 프로세스를 반복합니다.
- Use _Select Tuning_ radio button to select the axis to tune
- 적절한 스틱을 이동합니다 (예 : 피치 스틱, 요 스틱).
- 피치 튜닝의 경우 롤과 동일한 값으로 시작하십시오.
:::tip
Use the **Save to Clipboard** and **Reset from Clipboard** buttons to copy the roll settings for initial pitch settings.
:::
13. 모든 축에서 자세 콘트롤러에 대하여 튜닝 프로세스를 반복하십시오.
14. Repeat the tuning process for the velocity and positions controllers (on all the axes).
- Use Position mode when tuning these controllers
- Select the **Simple position control** option in the _Position control mode ..._ selector (this allows direct control for the generation of step inputs)

완료되었습니다 !
설정을 종료하기 전에 에어 모드를 다시 활성화하여야 합니다.