# Holybro Pixhawk 4 (Discontinued) ::: warning This flight controller has been [discontinued](../flight_controller/autopilot_discontinued.md) and is no longer commercially available. It is still supported by PX4. ::: ::: warning PX4 does not manufacture this (or any) autopilot. Contact the [manufacturer](https://holybro.com/) for hardware support or compliance issues. ::: [_Pixhawk 4_](https://holybro.com/products/pixhawk-4)® is an advanced autopilot designed and made in collaboration with Holybro® and the PX4 team. It is optimized to run PX4 v1.7 and later, and is suitable for academic and commercial developers. It is based on the [Pixhawk-project](https://pixhawk.org/) **FMUv5** open hardware design and runs PX4 on the [NuttX](https://nuttx.apache.org/) OS. ::: tip This autopilot is [supported](../flight_controller/autopilot_pixhawk_standard.md) by the PX4 maintenance and test teams. ::: ## Specifications {#specifications} ### Processor {#processor} - **Main FMU processor:** STM32F765 (32 Bit Arm® Cortex®-M7, 216 MHz, 2 MB flash, 512 KB RAM) - **IO processor:** STM32F103 (32 Bit Arm® Cortex®-M3, 72 MHz, 64 KB SRAM), or STM32F100 (32 Bit Arm® Cortex®-M3, 24 MHz, 8 KB SRAM) on earlier boards ### Sensors {#sensors} - **IMU:** ICM-20689 (SPI1), and BMI055 or ICM-20602 (SPI1) - **Barometer:** MS5611 (SPI4) - **Magnetometer:** IST8310 (I2C3) - **GPS module (external):** u-blox Neo-M8N GPS/GLONASS receiver, with integrated IST8310 magnetometer ### Interfaces {#interfaces} - **PWM outputs:** 16 (8 IO `MAIN`, 8 FMU `AUX`) - **Capture inputs:** 3 dedicated PWM/capture inputs on FMU - **Serial ports:** 4 (`GPS MODULE`, `TELEM1`, `TELEM2`, `UART & I2C B`) - **I2C buses:** 4 (I2C3 internal; I2C1 on `GPS MODULE`, I2C2 on `UART & I2C B`, I2C4 on `I2C A`) - **SPI buses:** 4 - **CAN buses:** up to 2, for dual CAN with serial ESC - **USB:** Micro-USB - **RC input:** dedicated input for CPPM, and dedicated input for Spektrum/DSM and S.BUS with analog/PWM RSSI input - **S.BUS output:** dedicated S.BUS servo output - **Parameter storage:** FRAM (SPI2) - **SD card:** MicroSD slot ### Electrical Data {#electrical_data} - **Input voltage:** 4.9 V to 5.5 V (`POWER1`, `POWER2`), 4.75 V to 5.25 V (`USB`) - **Max input voltage:** 6 V (`POWER1`, `POWER2`, `USB`) - **Servo rail input:** 0 V to 36 V - **Power monitoring:** analog inputs for voltage and current of 2 batteries, up to 120 A ### Mechanical Data {#mechanical_data} - **Dimensions:** 44 × 84 × 12 mm - **Weight:** 31.2 g (plastic case), 48.5 g (aluminium case) - **Operating temperature:** -40 °C to 85 °C ![Pixhawk 4 Dimensions](../../assets/flight_controller/pixhawk4/pixhawk4_dimensions.jpg) Additional information can be found in the [Pixhawk 4 Technical Data Sheet](https://cdn.shopify.com/s/files/1/0604/5905/7341/files/Pixhawk4-DataSheet.pdf). ## Where to Buy {#store} [Holybro](https://holybro.com/products/pixhawk-4) (No longer available). ## Pinouts {#pinouts} ![Pixhawk 4 connectors](../../assets/flight_controller/pixhawk4/pixhawk4-connectors.jpg) ::: warning The `DSM/SBUS RC` and `PPM RC` ports are for RC receivers only. These are powered! NEVER connect any servos, power supplies or batteries (or to any connected receiver). ::: Download _Pixhawk 4_ pinouts from [here](https://cdn.shopify.com/s/files/1/0604/5905/7341/files/Pixhawk4-Pinouts.pdf). ::: info Connector pin assignments are left to right (i.e. Pin 1 is the left-most pin). The exception is the [debug ports](#debug_port) (pin 1 is the right-most, as shown below). ::: ## Power {#power} The `POWER1` and `POWER2` ports are 6-pin inputs for analog power modules, which supply the board and report battery voltage and current. See [Pixhawk 4 Wiring Quick Start > Power](../assembly/quick_start_pixhawk4.md#power) for wiring, and [Battery and Power Module Setup](../config/battery.md) for configuration. ## Voltage Ratings {#voltage_ratings} _Pixhawk 4_ can be triple-redundant on the power supply if three power sources are supplied. The three power rails are: `POWER1`, `POWER2` and `USB`. ::: info The output power rails `FMU PWM OUT` and `I/O PWM OUT` (0 V to 36 V) do not power the flight controller board (and are not powered by it). The output rails must be [separately powered](../peripherals/pwm_escs_and_servo.md) if it needs to power servos or other hardware. You must supply power to one of `POWER1`, `POWER2` or `USB`, or the board will be unpowered. ::: **Normal Operation Maximum Ratings** Under these conditions all power sources will be used in this order to power the system: 1. `POWER1` and `POWER2` inputs (4.9 V to 5.5 V) 1. `USB` input (4.75 V to 5.25 V) **Absolute Maximum Ratings** Under these conditions the system will not draw any power (will not be operational), but will remain intact. 1. `POWER1`, `POWER2` and `USB` inputs (operational range 4.1 V to 5.7 V, 0 V to 6 V undamaged) 1. Servo input: `VDD_SERVO` pin of `FMU PWM OUT` and `I/O PWM OUT` (0 V to 42 V undamaged) ## PWM Outputs {#pwm_outputs} The Pixhawk 4 has 8 IO PWM outputs (`MAIN`) on the `I/O PWM OUT` port, and 8 FMU PWM outputs (`AUX`) on the `FMU PWM OUT` port. [DShot](../peripherals/dshot.md) can be used on FMU outputs 1-4 (group1). [Bidirectional DShot](../peripherals/dshot.md#bidirectional-dshot-telemetry) is not supported. The 8 FMU outputs are in 3 groups: - Outputs 1-4 in group1 (Timer1) - Outputs 5-6 in group2 (Timer4) - Outputs 7-8 in group3 (Timer12) All outputs within the same group must use the same output protocol and rate. The 3 capture inputs (`FMU_CAP1` to `FMU_CAP3`, Timer2) are on the `CAP & ADC IN` port, and appear in the [actuator configuration](../config/actuators.md) as `PWM Capture 1-3`. They can also be used as extra PWM or OneShot outputs. ## SD Card (Optional) {#sd_card} The Pixhawk 4 has a MicroSD card slot. See [SD Cards](../getting_started/px4_basic_concepts.md#sd-cards-removable-memory) and [Pixhawk 4 Wiring Quick Start > SD Card](../assembly/quick_start_pixhawk4.md#sd_card). ## Serial Port Mapping {#serial_port_mapping} | UART | Device | Port | Flow Control | | ------ | ------------ | ------------------------- | ------------ | | USART1 | `/dev/ttyS0` | `GPS MODULE` (`GPS1`) | | | USART2 | `/dev/ttyS1` | `TELEM1` | Yes | | USART3 | `/dev/ttyS2` | `TELEM2` | Yes | | UART4 | `/dev/ttyS3` | `UART & I2C B` (`TELEM4`) | | | USART6 | `/dev/ttyS4` | `DSM/SBUS RC` | | | UART7 | `/dev/ttyS5` | `FMU Debug` (Console) | | | UART8 | `/dev/ttyS6` | PX4IO | | ## Assembly {#assembly} The [Pixhawk 4 Wiring Quick Start](../assembly/quick_start_pixhawk4.md) provides instructions on how to assemble required/important peripherals including GPS, Power Management Board etc. ### Radio Control {#radio_control} A remote control (RC) radio system is required if you want to manually control your vehicle (PX4 does not require a radio system for autonomous flight modes). You will need to [select a compatible transmitter/receiver](../getting_started/rc_transmitter_receiver.md) and then bind them so that they communicate. - Spektrum/DSM and S.BUS receivers connect to the `DSM/SBUS RC` port. A Spektrum/DSM receiver takes 3.3 V from pin 4, and an S.BUS receiver takes 5 V from pin 1. - PPM receivers connect to the `PPM RC` port. PWM receivers, which have one wire per channel, need a [PPM encoder](../getting_started/rc_transmitter_receiver.md#connecting-receivers). - [CRSF and GHST](../getting_started/rc_transmitter_receiver.md#compatible_receivers) receivers connect to a free `TELEM` port. Enable the driver by [setting](../advanced_config/parameters.md) [RC_CRSF_PRT_CFG](../advanced_config/parameter_reference.md#RC_CRSF_PRT_CFG) or [RC_GHST_PRT_CFG](../advanced_config/parameter_reference.md#RC_GHST_PRT_CFG) to that port. ### GPS & Compass {#gps_compass} Connect a GPS module to the 10-pin `GPS MODULE` port, which also carries its compass (I2C), safety switch, safety LED and buzzer. The board also has an internal IST8310 compass. A second GPS can be connected to the `UART & I2C B` port: set [GPS_2_CONFIG](../advanced_config/parameter_reference.md#GPS_2_CONFIG) to `TELEM/SERIAL 4`. See [Pixhawk 4 Wiring Quick Start](../assembly/quick_start_pixhawk4.md) and [Mounting a GPS/Compass](../assembly/mount_gps_compass.md). ### Telemetry Radios (Optional) {#telemetry} A [telemetry radio](../telemetry/index.md) can be connected to `TELEM1` without further configuration. You can also connect one to any spare serial port, such as `TELEM2`, and [configure MAVLink](../peripherals/mavlink_peripherals.md) on that port. ### CAN {#can} The `CAN1` and `CAN2` ports can be used for [DroneCAN](../dronecan/index.md) peripherals. DroneCAN is not enabled by default: set [UAVCAN_ENABLE](../advanced_config/parameter_reference.md#UAVCAN_ENABLE) to enable it. ## Building Firmware {#building_firmware} ::: tip Most users will not need to build this firmware! It is pre-built and automatically installed by _QGroundControl_ when appropriate hardware is connected. ::: To [build PX4](../dev_setup/building_px4.md) for this target: ```sh make px4_fmu-v5_default ``` ## Debug Port {#debug_port} The [PX4 System Console](../debug/system_console.md) (UART7) and [SWD interface](../debug/swd_debug.md) run on the `FMU Debug` port, while the IO console and SWD interface can be accessed via the `I/O Debug` port. In order to access these ports, the user must remove the _Pixhawk 4_ casing. ![Pixhawk 4 Debug Ports](../../assets/flight_controller/pixhawk4/pixhawk4_debug_port.jpg) The pinout uses the standard [Pixhawk debug connector pinout](https://github.com/pixhawk/Pixhawk-Standards/blob/master/DS-009%20Pixhawk%20Connector%20Standard.pdf): both debug ports are [Pixhawk Debug Mini](../debug/swd_debug.md#pixhawk-debug-mini) ports. For wiring information see: - [System Console > Pixhawk Debug Port](../debug/system_console.md#pixhawk_debug_port) ## Peripherals - [Digital Airspeed Sensor](https://store-drotek.com/793-digital-differential-airspeed-sensor-kit-.html) - [Telemetry Radio Modules](../telemetry/index.md) - [Rangefinders/Distance sensors](../sensor/rangefinders.md) ## Further Information {#further_information} - [Pixhawk 4 Technical Data Sheet](https://cdn.shopify.com/s/files/1/0604/5905/7341/files/Pixhawk4-DataSheet.pdf) (Holybro) - [FMUv5 reference design pinout](https://docs.google.com/spreadsheets/d/1-n0__BYDedQrc_2NHqBenG1DNepAgnHpSGglke-QQwY/edit#gid=912976165). - [Pixhawk 4 Wiring QuickStart](../assembly/quick_start_pixhawk4.md) - [Pixhawk 4 Pinouts](https://cdn.shopify.com/s/files/1/0604/5905/7341/files/Pixhawk4-Pinouts.pdf) (Holybro) - [Pixhawk 4 Quick Start Guide](https://cdn.shopify.com/s/files/1/0604/5905/7341/files/Pixhawk4-quickstartguide.pdf) (Holybro)